Inepro PayCon Touch - Pillar User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | PayCon Touch - Pillar
PayCon Touch - Pillar

PayCon Touch - Pillar
Congratulations on your selection of the Inepro PayCon Touch - Pillar. We are certain
you will be pleased with your purchase of one of the flexibele solutions of the market.
We want to help you get the best result from your PayCon Touch - Pillar. This manual
contains information on how to do that; please read it carefully. Due to continuous
product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its
coverage and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile payment solution

All rights reserved. No parts of this work may be reproduced in any form or by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claim to these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting from the
use of information contained in this document or from the use of programs and source code
that may accompany it. In no event shall the publisher and the author be liable for any loss of
profit or any other commercial damage caused or alleged to have been caused directly or
indirectly by this document.
Created: May 2019 in Nieuw-Vennep.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Grimmerink
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
J. van den Berg
PayCon Touch - Pillar
P. Blom

Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 10

ATTENTION!!
Read this manual carefully before installing the P ay C on Touch!
Mains connection
Guar entee
Security
Before connecting the appliance to the mains, check that the mains supply v oltage corresponds
to the v oltage printed on the ty pe plate of the adapter. If the mains v oltage is different, consult
y our supplier.
No guarantee can be giv en if safety regulations are not follow ed.
A lw ay s disconnect the pow er supply before handling any thing inside the dev ice.
This dev ice is in conformity w ith the EMC directiv e and low -v oltage directiv e.
CE Confor mité Eur opeène (Conform Eur opean Nor m)
End of life dir ectives
Inepro is pay ing a lot of attention to env ironmentally -friendly production. Your new dev ice contain
materials w hich can be recy cled and reused. A t the end of its life specialised companies can
dismantle the discarded dev ice to recy cle the reusable materials and to minimise the amount of
materials to be disposed of. P lease observ e the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This dev ice may only be used indoors.
Indoor User O nly
Directives

I
Introduction
Part

Introduction
2
Introduction
This instruction is for assembling the Inepro PayCon Touch stand.
We shall:
1. Check the content of the kit, read more on page
2. Prepare and construct the hardware, on page
4
11

II
Check Kit Content
Part

Check Kit Content
4
Check Kit Content
Before installing the kit, you should check if you have all the items
that you need.
Additional requirement for installation:
§ Copier device
320090 - PayCon Touch Pillar + Copier Interface Kit
Please check the content of this box and make sure all kits are
complete.
320090 - PayCon Touch Pillar + Copier Interface Kit
In the "PayCon Touch Pillar + Copier Interface Kit" you should find:
§ 1x PayCon Touch Pillar
§ 1x PayCon Touch Base Package

5 - PayCon Touch - Pillar
§ 1x PayCon Touch Cables and Cover Package
§ 1x PayCon Touch Kit

Check Kit Content
6
Cables and Cover Pacakage
Cables and Cover
In the Cables and Cover Package you should
find:
· 2x USB 2.0 A-B Type cables 1.8m.
· 2x Network patch cable 1.5m.
· 1x Power cable
· 1x Rubber cover
· 1x Set of Copier Interface cables + accessories. Beware! This set may
differ as it depends on your copier!
oIn this example:
§ 1x Copier Interface Gender Changer
§ 1x Copier Interface Cable

7 - PayCon Touch - Pillar
PayCon Touch Base Package
PayCon Touch Base Package
In the PayCon Touch Base Package you should find:
§ 1x PayCon Touch Base Plate
§ 1x Copier Interface Board
§ 1x Copier Interface Board Cover
§ 2x M10 x 25mm Bolts
§ 2x M10 x 20mm x 2mm Washers
§ 10x M3 Pan head Philips machine screws 8mm

Check Kit Content
8
PayCon Touch Kit
In the PayCon Touch Kit you should find:
§ 1x User Manual
§ 1x Release Notes
§ 4x Dome Head Alan / hex keymachine screws
§ 1x PayCon Touch
§ 1x Network cable 2.5m.
§ 1x Power adaptor set

9 - PayCon Touch - Pillar
PayCon Touch Kit

III
Hardware Setup
Part

11 - PayCon Touch - Pillar
Hardware Setup
We will construct the PayCon stand using these tools:
§ An M17 spanner
§ A Hex / Alan / Umbrako / Inbus key, 2.5mm
§ A Philips type 1 screwdriver
1. Attach the base of the pillar to the pillar using the M10 washers
and bolts.

Hardware Setup
12
2. Fasten the copier interface with 6 of the 10 machine screws.

13 - PayCon Touch - Pillar
3. Connect the first network cable from the unshielded RJ-45
connector to the unshielded connector on the interface board.
4. Connect the second network cable from the shielded RJ-45
connector to the shielded connector on the interface board.
5. Connect the power cable to the power outlet on the interface
board.
6. Connect both the USB cables.
7. Connect the copier interface cable to the correct interface on the
board, and connect to the copier.
8. Connect the power supply and connect it to a power outlet.
9. Connect the network cable and connect it to a working network
outlet.

Hardware Setup
14
10. Mount the cover over the Copier Interface Board with the last 4
screws.

15 - PayCon Touch - Pillar
11. Feed the cables trough the pillar.
12. Now we will apply the cover. Make sure the cut part of the cover
is at the bottom of the pillar.
13. Fit the cover on the pillar. Push it into place from the side.