Inepro PayMatic 4B - Xerox MFP Manual

PayMatic 4B - Xerox MFP
EN
Congratulations on your selection of the PayMatic 4B - Xerox MFP. We are certain
you will be pleased with your purchase of one of the flexibele solutions of the
market.
We want to help you get the best result from your PayMatic 4B - Xerox MFP. This
manual contains information on how to do that; please read it carefully. Due to
continuous product improvements this manual is subject to changes without
notice.
We strongly recommend you read the license agreement to fully understand its
coverage and your responsibilities of ownership.
Your dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
© 2022 inepro All rights reserved.
ineproB.V.

PayMatic 4B - Xerox MFP - Install Manual | EN
All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic,
electronic, or mechanical, including photocopying, recording, taping, or information storage and
retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered trademarks of
the respective owners. The publisher and the author make no claim to these trademarks.
While every precaution has been taken in the preparation of this document, the publisher and the
author assume no responsibility for errors or omissions, or for damages resulting from the use of
information contained in this document or from the use of programs and source code that may
accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other
commercial damage caused or alleged to have been caused directly or indirectly by this document.
Revision number R 6. This revision of the manual can be applied to products with version 7.0 or higher.
Publisher
inepro B.V.
Managing Editor
K. de Graaf
Technical Editors
P. Grimmerink
J. van den Berg
P. Blom
K. de Graaf
Cover Design
K. de Graaf
M. Sterk
Team Coordinator
R. Groen
Production
inepro B.V.

PayMatic 4B - Xerox MFP
Table of Contents
Introduction 1
Configuration 3
1 ............................................................................................................................................................................................................ 4Accounting Mode
2 ............................................................................................................................................................................................................ 5Auxiliary Device Type
3 ............................................................................................................................................................................................................ 5Service Access & Accounting
4 ............................................................................................................................................................................................................ 6Other
5 ............................................................................................................................................................................................................ 7Log Out

Directives
ATTENTION!!
Read this manual carefully before installing the PayMatic 4B - Xerox MFP!
Mains connection
Before connecting the appliance to the mains, check that the mainssupply voltage corresonds to the
voltage printed on the type plate of the adapter. If the mains voltage is different, consult your supplier.
Guarentee
No guarantee can be given if safety regulations are not followed.
Changes and/or modifications
Changes and/or modfications whch have not been approved by the responsible party can void the
user's authorty to operate the equitement.
Security
Always disconnect the power supply before handling anything inside the device.
End of life directives
Inepro is paying a lot of attention to environmentally-friendly production. Your new device contain materials which
can be recycled and reused. At the end of its life specialised companies can dismantle the discarded device to
recycle the reusable materials and to minimise the amount of materials to be disposed of. Please observe the local
regulations regarding the disposal of packaging materials, exhausted batteries and old requipment.
CE Conformité Europeéne (Conform European Norm)
This device is in conformity with the EMC directive and low-voltage
directive.
For Indoor Use Only
This device may only be used indoors.
This document:
Due to continuous prduct imporovements this manual is subject to change without notice. This document
describes the technical and functional operation of the PayMatic 4B - Xerox MFP. Greatest care has been taken
drafting the information in this manual and it may be said thatit is reliable. However, the producer is not liable for
any shortcomings in the text or incompleteness of the information.
Thank you for your decision to use the PayMatic 4B - Xerox MFP.

Introduction
1

Introduction
Page 2 of 12
PayMatic 4B - Xerox MFP | EN
This manual is meant to help you to configure the PayMatic 4B and Xerox MFP to work with each other.
Xerox MFP Configuration for Inepro PayMatic 4B
When the FDI (Foreign device Interface) is installed on the MFP (Multi Functional Printer) and the
PayMatic is connected, login as administrator (= factory default login) at the device touch screen.
Press the "Log in / Log out" button in the upper right corner of the Xerox console panel.
Login with user name "admin" and password "1111" (= factory default login, may be different at the
customer's MFP).
Press the "Machine Info" button in the bottom left corner of the Xerox console panel to enter the
menu.
Go to the Tools tab

Configuration
2

Configuration Accounting Mode
Page 4 of 12
PayMatic 4B - Xerox MFP | EN
Accounting Mode
At Accounting Settings -> Accounting Mode
Set Accounting Mode to Auxiliary Access

Configuration Auxiliary Device Type
Page 5 of 12
PayMatic 4B - Xerox MFP | EN
Auxiliary Device Type
Set Auxiliary Device Type to Card Activated
Service Access & Accounting
At Service Access & Accounting make sure all services are selected to restrict and Copy is selected at
services you want to track usage

Configuration Other
Page 6 of 12
PayMatic 4B - Xerox MFP | EN
Other
Set Job Timeout to "1" second.
Set Double Count Large Impressions to Count Once.

Configuration Other
Page 7 of 12
PayMatic 4B - Xerox MFP | EN
Set Premium Select to None.
Press Save
Log Out
Press the "Log in / Log out" button in the upper right corner of the Xerox console panel again.
Select "Logout" to logout as administrator.

Configuration Log Out
Page 8 of 12
PayMatic 4B - Xerox MFP | EN
The default screen should now be the following: