Inside Weather SOFA SECTIONAL User manual

SOFA SECTIONAL

Gather Your Eggs...
BACK PILLOWS
BACK PLATE
2 ARMS
CHAISE LOUNGE CUSHION
SEAT CUSHIONS
2 INNER SUPPORT BRACES
CONNECTION BRACKET
OTTOMAN BASE
8 SLATS
FRONT PLATE
27 SLATS
A
A
B
B
C
CC
D
E
D E E
F
F
G
G
H
H
I
J
JK
K
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
I

You should have:
6x LEGS
4x CORNER BRACKETS
16x NEOPRENE
STICKY PADS
40x BUTTON HEAD HEX SCREW
(5 MM HEX BIT)
4x WASHERS
4x BUTTON HEAD HEX SCREW
(4 MM HEX BIT)
24x SOCKET HEAD CAP SCREW
DRILL + EXTENSION
5MM HEX BIT
4MM BALL HEAD BIT
USB CHARGER
Note: Drill may need to be charged before use
Note: Don’t be surprised if you find a few extra screws, washers and even an extra support brace
among your supplies. It’s just our way of being extra sure you have everything you need.

Align the arm and back panels
so that the wooden frames
meet at a right angle. Lean
the arm slightly away from the
back panel. Lift the top of the
back panel and gently lower
the hook until it connects.
Repeat on both sides.
Step 1: Connect the Arms
Connect the Hooks
Stand the arm on its side.
Identify the corresponding hooks
located on the arm and back panel.
This is how they connect.
The connection is the same
for both sides
Let’s start by connecting the arms to the back panel. Lay the back panel flat
on the floor, workbench or other stable surface with the metal strip is facing up.
The process is identical for both arms.

Connect the Arms (Continued)
Place a corner bracket to connect
the back and arm panels.
Put a 5mm button head socket cap
screw in each of the three holes in
the back panel. Losely hand tighten
only for now.
Screws will be tightened after they
have all been placed.
Connect the corner bracket to the
arm by hand-threading a button
head socket cap screw into each
of the three remaining holes.
Once all six screws have been
connected, use the drill to fasten
each bracket until secure.

Step 2: Install the Inner Support Braces
You’ll Need: 2x INNER SUPPORT BRACES
16x BUTTON HEAD SOCKET CAP SCREW (5 MM HEX BIT)

Install the Inner Support Braces (Continued)
Make sure the edges are flush
Hand tighten before finishing with
the drill to make sure everything is
properly aligned.
Repeat on the other end of
the brace.
Line up the holes in the support
brace with the corresponding
holes on the frame.

Step 3: Attach the Front Plate
FRONT PLATE
CORNER BRACKETS
5MM BUTTON HEAD SCREWS
1x
2x
12x
You’ll Need:
In this step we’ll be
adding the front plate.
But first let’s make sure
everything is ready!
Set the front plate between the
two arms as shown. Make sure that
the flap of excess fabric is facing
the top of the couch and hanging
toward the inside of the frame.
This will ensure that the plate is
rotated correctly.

Attach the Front Plate (Continued)
Attach a corner bracket to
the front plate using 3 bolts.
Hand tighten only
Hold the corner bracket flat
against the front plate and
add 3 more bolts to attach
the bracket to the arm.
Go back over eack screw
and use the drill to tighten
until secure.

Step 4: Install the Legs (Sofa)
Start by aligning the leg over the mounting holes. Insert
bolts into corresponding threaded holes as shown and
tighten by hand.
Note: if you have flared legs, make sure that each leg
points outward toward its respective corner.
Once each bolt is started by hand, use the
drill to finish securing the leg.
Repeat for all four legs.
4x LEGS
16x SOCKET HEAD CAP SCREW
You’ll Need: Note: Our legs are universal, and are used across
multiple products. All sofa and ottoman legs will
attach securely with 4 fasteners per leg.

Step 5: Install the Legs (Ottoman)
Install the 2 legs needed for
the ottoman section. These will
be installed at the front of the
ottoman base. The rear of the base
will be secured by a bracket in the
next step.
Follow the same instructions as the
previous step for both legs.
Install the 2 legs needed for
the ottoman section. These will
be installed at the front of the
ottoman base. The rear of the base
will be secured by a bracket in the
next step.
Follow the same instructions as the
previous step for both legs.
You’ll Need: 2x LEGS
8x SOCKET HEAD CAP SCREW

Begin by selecting which side of the Sofa
you would like the sectional cushion to be
on. Don’t worry, you can change sides at
anytime.
Taking the sectional connection bracket,
slide the bracket up and align the bracket
openings with the correspponding holes.
Use the socket head cap screws to secure
the ottoman base to the Sofa. Use 2 per side.
Step 6: Attach Sectional Bracket
Socket head cap screws line up
with corresponding holes in the
connection bracket and frame.

Step 7: Add the Neoprene Pads
Slats should look like the
diagram after the pads
have been added.
To keep the cushions from sliding
add the non-slip neoprene pads.
2 pads will be stuck onto a slat.
Only 6 of the slats of the sofa will
need pads.
Please see diagram for correct
placement.

Step 8: Place the Slats
Step 9: Add the Cushions
DONE!
Lay a slat in each groove, as
shown. Be sure they arch upward.
NOTE: You may need to gently
coax some slats into place
depending on how tightly
everything has been assembled.

Fabric Care Instructions
Cleaning Codes
Machine Washable
Spot Cleaning
SOLVENT OR WATER CLEANABLE (S/W)
WATER CLEANABLE (W)
SOLVENT CLEANABLE (S)
SPOT CLEAN ONLY (SC)
Spot clean with upholstery shampoo, foam from a mild detergent, or a mild dry cleaning solvent.
Spot clean fabric with a water-based shampoo or foam upholstery cleaner. Avoid over-wetting the stain.
Must be cleaned with solvents (dry clean only). Spot treat stains with a water-free solvent or
dry-cleaning product.
Cleaning depends on the nature of the stain. For oil-based spots, do not apply water and use dry
cloth. Recommended use of leather-specific solvents & cleaners.
Each fabric type has a specific cleaning code which can be found on the Free Swatch Page.
Many of our fabrics are machine washable. If a fabric is machine washable, it’ll be noted in the
cleaning instructions on the Free Swatch page. It must be Machine Wash - Cold. Use Cold Water
and a mild detergent on a low/gentle cycle. Hang dry all covers. Please note that every machine
wash adds wear to the fabric so it’s recommended to opt for spot cleaning prior to machine
washing whenever possible.
We recommend spot cleaning with either an upholstery shampoo, foam from a mild detergent, or
a mild cleaning solvent. Always hang to dry. When spills happen, blot immediately to remove the
spilled material. Clean spots or stains from the outside to the middle of the affected area (this prevents
circling). To prevent overall soiling, frequent vacuuming to remove dust and grime is recommended.