Inspur NF3120M5 User manual

V01502G000000000
Warnings!
15kg
30kg
50kg
● During the installation process, please do not block the vents on the server, especially the
vents on the front and rear of the server.
● Please remove the protective film from the server surface before using.
● Please leave a minimum of 15cm clearance on the front and rear sides of the server for
proper ventilation.
● Please install air baffles in place prior to device installation, to make sure that the server can
get enough air flow, and to avoid air turbulence in the server room.
● Servers are high-power electrical appliances, and they should be installed into dedicated
cabinets with vents or professional water-cooled cabinets, to prevent system failures caused
by overheating.
● If it needs to install more than one device, please load them from the bottom to the top, and
load the heaviest items first.
● Please note the cabinet’s load-bearing capacity, power supply capacity and heat
dissipation capacity, be sure not to install devices beyond the cabinet’s threshold capacity.
● For the convenience of using the front and rear ports of the server and cabling, leave a
minimum clearance of 70mm between the front end of the server and the inner side of the
cabinet’s front door, and 150mm between the rear end of the server and the inner side of the
cabinet’s rear door.
If the device is more than 15kg, at least 2 people are needed.
If the device is more than 30kg, at least 3 people are needed.
If the device is more than 50kg, at least 4 people are needed.
The cabinet, chassis or guide rails may cause serious scratches,
please be careful while handling.
When installing new servers into the cabinet in use, please be
aware of electric shock.
V1.0
Rack-Mounted Server
Installation Guide
Please keep this document for future reference.

Rack-Mounted Server Installation Guide V1.0
1
Pull the middle rails fully extended in lock position. Lift the server, align the inner
rails with the middles, and push the server slowly until it hits a stop.
Installing the server
1
2
2
3
Position the rail on the rack. Fix the rear bracket first, and insert the guide pins
into the rack holes.
Open the latch on the front bracket. Align the guide pins with the rack holes,
and insert the pins into the holes. Release the latch.
Install the other rail in the same way.
Notice: Keep the front and rear brackets at the same height, and keep the
two rails on the same level.
4
5
Remove the screws within the left and right lugs. Pull the server outward, and
pull the latches on the inner rails upward to remove the server from the rack.
Slightly lift up the keyhole spring plates, and slide the inner rails forward to
remove the inner rails.
Caution: Do not over bend the spring plate to avoid damage.
Removing the rails
1
2
Open the latches on the front brackets, and remove the rails.
3
Pull down the covers of the left and right lugs, and tighten the screws within.
3
Inner rail
Middle rail
Front bracket
Outer rail
Rear bracket
1
2
Installing the rails
Rail I: Pull the latch upward, and pull the inner rail outward to remove it.
Rail II: Pull the white tab forward and take out the inner rail.
1
Align the keyholes on the inner rail with the standoffs on the chassis, and push
the rail in the direction of the arrow to install the inner rail onto the chassis.
➋
➊
Innerrail
Middlerail
Outerrail
white
2 2
1 1
Rail I Rail II
The following describes the installation methods of two kinds of screw-free rails.
Please select the suitable method according to the specific rails. 1 1
22
Rail I Rail II
Rail II: Pull or push the blue release tab, and
push the server inward until the inner rails fully
enter the middle rails. Press the two tabs on
the middle rails while pushing the server into
place.
Rail I: Pull the latches on the inner rails upward,
and push the server into place.
blue
➋
➊