Integra 3215 User manual

Linear Stand Operating instructions
163952_V02
Charging Stations for Linear Stand

Declaration of conformity
INTEGRA Biosciences AG – 7205 Zizers, Switzerland
declares on its own responsibility that the devices
comply with:
Zizers, December 6, 2019
Description Models
Linear Stand 3215
Charging Station for Linear Stand 3217
Charging/Communication Station for Linear Stand 3218
EU Directives (DoW: Date of Withdrawal) Before DoW DoW After DoW
Low Voltage Equipment 2006/95/EC 20.04.2016 2014/35/EU
Electromagnetic Compatibility 2004/108/EC 20.04.2016 2014/30/EU
Restriction of Hazardous Substances 2011/65/EU
Waste Electrical and Electronic Equipment 2012/19/EU
EU Regulation
Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) 1907/2006
Standards for EU
Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.
EN 61010-1: 2010
Electrical equipment for measurement, control and laboratory use -
EMC requirements.
EN 61326-1: 2013
Standards for Canada and USA
Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.
CAN/CSA-C22.2
No. 61010-1
Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.
UL 61010-1
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
Part 15 of the
FCC Rules
Class A
Urs Hartmann
CEO
Thomas Neher
Quality Manager

Linear Stand Charging Stations - Operating instructions V02
www.integra-biosciences.com 3
Table of Contents
1 Introduction ................................................................................................................ 3
2 Installation .................................................................................................................. 3
3 Disposal ..................................................................................................................... 5
4 Accessories................................................................................................................ 5
1 Introduction
1.1 Intended use
The Linear Stand is used to hang up your INTEGRA Biosciences pipettes.
The Charging Station and the Charging/Communication Station, here Charging Stations
for short, are mounted on the Linear Stand (#3215) to charge VIAFLO/
VOYAGER Electronic Pipettes from INTEGRA Biosciences. Using the Charging/
Communication Station, the pipettes can be connected to VIALINK via a PC. VIALINK
allows the user to upload/download custom programs, images, firmware updates and
service history to and from VIAFLO and VOYAGER pipettes.
The Charging Stations have been designed for use in a laboratory. They shall be used in
a dry and dust-free location with a temperature of 5–40 °C and a maximal (non-
condensing) relative humidity of 80 %.
1.2 Safety notes
1) Do not use the Charging Stations in an atmosphere with danger of explosion.
2) Use an original INTEGRA Biosciences Mains Adapter (#3216) only.
3) Prolonged exposure of Charging Stations to UV-light can cause discoloration and/or
yellowing of the plastic housing. This will not affect the performance of the device in any
way.
Please visit our website www.integra-biosciences.com on a regular basis for up to date
information regarding REACH classified chemicals contained in our products.
2 Installation
2.1 Assembling the Linear Stand
Push the upper ends of the two support
feet into the connecting rail (a).
a

Linear Stand Charging Stations - Operating instructions V02
4 INTEGRA Biosciences AG
2.2 Mounting the Charging Stations
Note: The Charging Stations (#3217, #3218), Linear Stand (#3215) and Mains Adapter
(#3216) must be ordered separately.
1) Take the Linear Stand (#3215) and pull one of the two
support feet off the connecting rail.
2) Loosen the screw (b) on the Charging Station and slide
the rectangular washer (c) of the Charging Station on
the connecting rail.
3) Move the Charging Station to the desired position and
tighten the screw. Up to 4 Charging Stations can be
mounted to each linear stand.
4) Insert the plug (d) of mains adapter into the bottom of
the removed support foot and guide it through the foot.
5) Pass the cable through the horizontal slot of the
connecting rail.
6) Connect the plug (d) with the Charging Station.
cb
d
d

Linear Stand Charging Stations - Operating instructions V02
www.integra-biosciences.com 5
3 Disposal
The Linear Stand can be disposed of with municipal waste. The
Charging Stations and the Mains Adapter must not be disposed of with
unsorted municipal waste. Do not dispose them in a fire.
Dispose of the Charging Stations and the Mains Adapter in accordance with the
laws and regulations in your area governing disposal of devices.
4 Accessories
Imprint
© 2019 INTEGRA Biosciences AG
Manufacturer
7) Push the support foot back on the Linear Stand.
8) Connect the Charging Stations serially using the
connection cable (e).
9) Insert the plug of the USB cable (f) into the socket of
the Charging/Communication Station, if applicable.
Accessories Part No.
Linear Stand holds up to 4 Charging Stations 3215
Mains Adapter for use with Linear Stand (100–240 VAC, 50/60 Hz) 3216
Charging Station for
Linear Stand
for INTEGRA Electronic Pipettes
(incl. connection cable)
3217
Charging/Communi-
cation Station for
Linear Stand
for INTEGRA Electronic Pipettes
(incl. connection cable and USB cable)
3218
INTEGRA Biosciences AG
CH-7205 Zizers, Switzerland
T [phone]
F [phone]
INTEGRA Biosciences Corp.
Hudson, NH 03051, USA
T [phone]
F [phone]
[e-mail]
www.integra-biosciences.com
f
e