Intel NUC11PAQi7 User manual

1
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
Intel® NUC Kit NUC11PAQi7
Intel® NUC Kit NUC11PAQi5
User Guide
January 2021

2
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products
described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject
matter disclosed herein.
No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document.
All information provided here is subject to change without notice. Contact your Intel representative to obtain the latest Intel product
specifications and roadmaps.
The products described may contain design defects or errors known as errata which may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Copies of documents which have an order number and are referenced in this document may be obtained by calling 1-800-548-4725 or by
visiting: http://www.intel.com/design/literature.htm.
Intel technologies' features and benefits depend on system configuration and may require enabled hardware, software or service activation.
Performance varies depending on system configuration. No computer system can be absolutely secure.
Intel and the Intel logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2021, Intel Corporation. All rights reserved.

3
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
Contents
1.0 Introduction .............................................................................................................................5
1.1 Before You Begin ...........................................................................................................................................5
1.2 Installation Precautions.............................................................................................................................5
1.3 Observe Safety and Regulatory Requirements.........................................................................6
2.0 Open the Chassis ...................................................................................................................7
3.0 Install and Remove System Memory .........................................................................8
3.1 Install SO-DIMMs...........................................................................................................................................8
3.2 Remove SO-DIMMs ......................................................................................................................................9
4.0 Install an M.2 SSD...............................................................................................................10
5.0 Install a 2.5-inch SSD or Hard Drive........................................................................12
6.0 Close the Chassis.................................................................................................................13
7.0 Use the VESA Bracket (Optional)...............................................................................14
8.0 Connect Power ......................................................................................................................16
9.0 Install an Operating System .........................................................................................18
10.0 Install the Latest Device Drivers and Software ................................................19

4
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
Revision History
Date
Revision
Description
January 2021
1.0
Initial release.

5
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
1.0 Introduction
This User Guide provides step-by-step installation instructions for these products:
•Intel® NUC Kit NUC11PAQi7
•Intel® NUC Kit NUC11PAQi5
1.1 Before You Begin
CAUTIONS
The steps in this guide assume you’re familiar with computer terminology and
with the safety practices and regulatory compliance required for using and
modifying computer equipment.
Disconnect the computer from its power source and from any network before
performing any of the steps described in this guide.
Failure to disconnect power, telecommunications links, or networks before you open
the computer or perform any procedures can result in personal injury or equipment
damage. Some circuitry on the board can continue to operate even though the front
panel power button is off.
Follow these guidelines before you begin:
•Always follow the steps in each procedure in the correct order.
•Create a log to record information about your computer, such as model,
serial numbers, installed options, and configuration information.
•Electrostatic discharge (ESD) can damage components. Perform the
procedures described in this chapter only at an ESD workstation using an
antistatic wrist strap and a conductive foam pad. If such a station isn’t
available, you can provide some ESD protection by wearing an antistatic wrist
strap and attaching it to a metal part of the computer chassis.
1.2 Installation Precautions
When you install and test the Intel NUC, observe all warnings and cautions in the
installation instructions.
To avoid injury, be careful of:

6
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
•Sharp pins on connectors
•Sharp pins on circuit boards
•Rough edges and sharp corners on the chassis
•Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
•Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing
to qualified technical personnel.
1.3 Observe Safety and Regulatory Requirements
If you don’t follow these instructions, you increase your safety risk and the possibility
of noncompliance with regional laws and regulations.

7
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
2.0 Open the Chassis
Unscrew the four corner screws on the bottom of the chassis and lift the cover.

8
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
3.0 Install and Remove System Memory
Intel NUC Kits NUC11PAQi7, NUC11PAQi5 have two 260-pin DDR4 SO-DIMM
memory slots
Memory requirements:
•1.2V low voltage memory
•3200 MHz SO-DIMMs
•Non-ECC
Find compatible system memory modules at the Intel® Product Compatibility Tool:
•NUC11PAQi7
•NUC11PAQi5
3.1 Install SO-DIMMs
NOTE
If you plan to install only one memory module, install it in the lower
memory socket.
To install the SO-DIMMs, follow these steps:
1. Observe the precautions in "Before You Begin" in Section 1.1.
2. Turn off all peripheral devices connected to the computer. Turn off the
computer and disconnect the AC power cord.
3. Align the small notch at the bottom edge of the SO-DIMM with the key in
the socket.
4. Insert the bottom edge of the SO-DIMM into the socket.
5. When the SO-DIMM is inserted, push down on the outer edge of the
SO-DIMM until the retaining clips snap into place. Make sure the clips
are firmly in place.

9
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
3.2 Remove SO-DIMMs
To remove a SO-DIMM, follow these steps:
1. Observe the precautions in "Before You Begin" in Section 1.1.
2. Turn off all peripheral devices connected to the computer. Turn off the
computer.
3. Remove the AC power cord from the computer.
4. Remove the computer’s cover.
5. Gently spread the retaining clips at each end of the SO-DIMM socket. The
SO-DIMM pops out of the socket.
6. Hold the SO-DIMM by the edges, lift it away from the socket, and
store it in an anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the
SO-DIMM sockets.
8. Replace the computer’s cover and reconnect the AC power cord.

10
NUC11PAQi7, NUC11PAQi5
User Guide –January 2021
4.0 Install an M.2 SSD or Intel® Optane™ Memory
Module
Intel NUC Kits NUC11PAQi7, NUC11PAQi5 support 80mm and 42mm SSDs.
Find compatible M.2 SSDs at the Intel® Product Compatibility Tool:
•NUC11PAQi7
•NUC11PAQi5
If you’re installing an 80mm M.2 SSD:
1. Remove the small silver screw from the 80mm metal standoff on the
motherboard (A).
2. Align the small notch at the bottom edge of the M.2 card with the key in the
connector.
3. Insert the bottom edge of the M.2 card into the connector (B).
4. Secure the card to the standoff with the small silver screw (C).
Intel® Optane™ Memory Module installation and integration instructions are available
by this link