Intermec EasyCoder PD4 User manual

Installation
Instructions
EasyCoder PD4
Cutter

ii EasyCoder PD4 Cutter Installation Instructions
Intermec Technologies Corporation
Corporate Headquarters
6001 36th Ave. W.
Everett, WA 98203
U.S.A.
www.intermec.com
e information contained herein is proprietary and is provided solely for the
purpose of allowing customers to operate and service Intermec-manufactured
equipment and is not to be released, reproduced, or used for any other pur-
pose without written permission of Intermec.
Information and specifications contained in this document are subject to
change without prior notice and do not represent a commitment on the part
of Intermec Technologies Corporation.
© 2005 by Intermec Technologies Corporation. All rights reserved.
e word Intermec, the Intermec logo, and EasyCoder are either trademarks
or registered trademarks of Intermec Technologies Corporation.
roughout this manual, trademarked names may be used. Rather than put
a trademark (™ or ®) symbol in every occurrence of a trademarked name, we
state that we are using the names only in an editorial fashion, and to the ben-
efit of the trademark owner, with no intention of infringement.
ere are U.S. and foreign patents pending.

EasyCoder PD4 Cutter Installation Instructions iii
Contents
Contents
Before You Begin........................................................................... iv
Safety Summary.............................................................. iv
Global Services and Support ............................................ v
1 Installation
Installing the Cutter.......................................................................2

iv EasyCoder PD4 Cutter Installation Instructions
Before You Begin
Before You Begin
is section provides you with safety information, technical support informa-
tion, and sources for additional product information.
Safety Summary
Your safety is extremely important. Read and follow all warnings and cautions
in this document before handling and operating Intermec equipment. You can
be seriously injured, and equipment and data can be damaged if you do not
follow the safety warnings and cautions.
Do not repair or adjust alone
Do not repair or adjust energized equipment alone under any circumstances.
Someone capable of providing first aid must always be present for your safety.
First aid
Always obtain first aid or medical attention immediately after an injury. Never
neglect an injury, no matter how slight it seems.
Resuscitation
Begin resuscitation immediately if someone is injured and stops breathing.
Any delay could result in death. To work on or near high voltage, you should
be familiar with approved industrial first aid methods.
Energized equipment
Never work on energized equipment unless authorized by a responsible
authority. Energized electrical equipment is dangerous. Electrical shock from
energized equipment can cause death. If you must perform authorized emer-
gency work on energized equipment, be sure that you comply strictly with
approved safety regulations.

EasyCoder PD4 Cutter Installation Instructions v
Before You Begin
Global Services and Support
Warranty Information
To understand the warranty for your Intermec product, visit the Intermec web
site at http://www.intermec.com and click Service & Support. e Intermec
Global Sales & Service page appears. From the Service & Support menu, move
your pointer over Support, and then click Warranty.
Web Support
Visit the Intermec web site at http://www.intermec.com to download our
current documents in PDF format. To order printed versions of the Intermec
manuals, contact your local Intermec representative or distributor.
Visit the Intermec technical knowledge base (Knowledge Central) at http://
intermec.custhelp.com to review technical information or to request technical
support for your Intermec product.
Telephone Support
Contact your local Intermec representative. To search for your local representa-
tive, from the Intermec web site, click Contact.
Who Should Read This Document?
is Installation Instructions provides you with information about how to
install the EasyCoder PD4 Cutter.
Related Documents
e Intermec web site at http://www.intermec.com contains our current docu-
ments that you can download in PDF format. To order printed versions of the
Intermec manuals, contact your local Intermec representative or distributor.

vi EasyCoder PD4 Cutter Installation Instructions
Before You Begin

EasyCoder PD4 Cutter Installation Instructions 1
1 Installation
is chapter describes how to install the EasyCoder
PD4 Cutter.

2 EasyCoder PD4 Cutter Installation Instructions
Chapter 1 — Installation
Installing the Cutter
1Unpack your EasyCoder PD4 cutter kit and check to see that all parts are
included. If not, contact your sales representative.
Front cover
Screw
2Make sure the printer is unplugged. Remove the screw
that holds the front cover. Remove the front cover.
Cutter
mechanism
Cutter cover
2 screws
with washers
2 cable
clips
Cutter tray

EasyCoder PD4 Cutter Installation Instructions 3
Chapter 1 — Installation
Tear bar
Screws
3Open the side door and remove the tear bar, which is
held by two Phillips screws.
4Attach the cutter mechanism to the printer using the two Phillips
screws and washers included in the kit.

4 EasyCoder PD4 Cutter Installation Instructions
Chapter 1 — Installation
Cable clips
Cutter cable
Cutter
connector
5Plug in the cable from the cutter into the rear one of the two connectors in
the center section and fasten the cable to the bottom plate using the two
cable clips included in the kit.
6Attach the cutter cover onto the cutter mechanism by first connecting the
hooks on the back side of the cover over the cutter mechanism and then
locking the cover with the screw at the bottom.