Intermec EasyCoder PF2i User manual

Installation
Instructions
EasyLAN
Interface Kit
(for EasyCoder PF2i,
PF4i, PF4i Compact
Industrial, and PM4i)

Intermec Printer AB
Idrottsvägen 10
P.O. Box 123
S-431 22 Mölndal
Sweden
Service support: [phone]
The information contained herein is proprietary and is provided solely
for the purpose of allowing customers to operate and/or service Intermec
manufactured equipment and is not to be released, reproduced, or used
for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change
without notice.
© 2003 by Intermec Printer AB
All Rights Reserved
EasyCoder, EasyLAN, and Fingerprint are registered trademarks of
Intermec Technologies Corp. The word Intermec, the Intermec logo,
InterDriver, PrintSet, and Duratherm are trademarks of Intermec Tech-
nologies Corp.
Microsoft is a registered trademark of Microsoft Corporation.
Torx is a registered trademark of Camcar Division of Textron Inc.
UNIX is a registered trademark of The Open Group in the United States
and other countries.
Windows is a trademark of Microsoft Corporation.
Throughout this manual, trademarked names may be used. Rather than
put a trademark (™) symbol in every occurrence of a trademarked name,
we state that we are using the names only in an editorial fashion, and to
the benefit of the trademark owner, with no intention of infringement.

Preface
Contents
Introduction ................................................................................. iv
Printer Firmware........................................................................... iv
Installation Kit.............................................................................. iv
1 Physical Installation
EasyCoder PF2/4i printers.............................................................2
EasyCoder PM4i printers...............................................................3
All Models .....................................................................................3
2 Setup in Fingerprint
Setup Methods...............................................................................8
Setting the New Line Parameter.....................................................8
Setting the Network Parameters .....................................................9
IP Selection .....................................................................9
Reading or Setting the IP Address..................................10
Reading or Setting the Netmask, Default Router, and
Name Server..................................................................10
3 Setup in IPL
Setup Methods.............................................................................14
Setting the Network Parameters ...................................................14
IP Selection ...................................................................14
Reading the IP Address..................................................15
Reading the Netmask, Default Router,
and Name Server ...........................................................15
Using ARP’n’PING to set an IP Address........................16
4 Accessing the Printer’s Home Page
Using the Web Browser................................................................22
Intermec EasyLAN Interface Kit Installation Instructions iii

Preface
iv Intermec EasyLAN Interface Kit Installation Instructions
Introduction
This Installation Instructions booklet describes how to install an
EasyLAN Ethernet interface in an EasyCoder PF2i, PF4i, PF4i Com-
pact Industrial, or PM4i printer and how to connect it to a LAN, WAN,
Intranet, or Internet network via an RJ-45 network cable.
The installation instructions describes how to physically install the inter-
face board in a printer and how to set up the IP address, netmask, default
router, and name server. The instructions end when you have the print-
er’s home page up and running. From there, please refer to the Intermec
EasyLAN User’s Guide on the attached CD-ROM.
This interface kit must only be physically installed by an
authorized service technician. Intermec assumes no respon-
sibility for personal injury or damage to the equipment if
the installation in performed by an unauthorized person.
Printer Firmware
The printer must either be fitted with Intermec Fingerprint v8.00 (or
later) or IPL v2.00 (or later). In Intermec Fingerprint, the Ethernet port
is addressed as device "net1:" (communication channel #5).
Installation Kit
The EasyLAN Interface Kit contains:
•One EasyLAN interface board
•One light guide
•One hexagonal threaded spacer
•One network extension cable
•One cable tie
•One serial number label
•One CD-ROM with software and manuals
•One Installation Instruction booklet
The only tool required for the installation is a #T20 Torx screwdriver and
a small wrench.

Intermec EasyLAN Interface Kit Installation Instructions 1
1 Physical Installation
This chapter describes how to physically install the
EasyLAN interface kit in a PF2/4i- or PM4i-series
printer.
The installation described in this chapter
must only be performed by an authorized
service technician.
Take precautions against electrostatic
discharges, for example by wearing
grounded bracelets.

2 Intermec EasyLAN Interface Kit Installation Instructions
Chapter 1 — Physical Installation
•Switch off the printer and disconnect the power cord.
•Disconnect all communication cables.
•Remove the front/left-hand cover as follows.
The electronic compartment contains wires and compo-
nents with dangerous voltage (up to 380V). Make sure that
the printer is switched off and the power cord is discon-
nected before the left-hand cover is removed.
EasyCoder PF2/4i printers
•Open the right-hand door.
•Using a #T20 Torx screwdriver, remove the three screws and lift the
cover up so it disengages the bottom plate.
•Swing out the rear part of the cover so you can disconnect the console
cable from the CPU board.
•Put the cover aside on a soft cloth or similar to avoid scratches.

Intermec EasyLAN Interface Kit Installation Instructions 3
Chapter 1 — Physical Installation
EasyCoder PM4i printers
•Using a #T20 Torx screwdriver, loosen the four screws that holds the
cover along the lower left edge of the bottom plate.
•Remove the four screws that hold the cover to the center section.
•Pull out the cover so you can disconnect the console cable from the
CPU board.
•Put the cover aside on a soft cloth or similar to avoid scratches.
All Models
•Remove the LAN connector plug, which is snap-locked at the top of
the rear plate.
•Remove the #T20 Torx screw that holds the upper/front part of the
CPU board to the power supply unit and replace it with the hexagonal
spacer included in the kit. Keep the screw.

4 Intermec EasyLAN Interface Kit Installation Instructions
Chapter 1 — Physical Installation
•Connect the EasyLAN board to the PCI connector (J84) on the CPU
board so the hole in the interface board becomes aligned with the
spacer.
•Secure the EasyLAN board with the #T20 Torx screw you previously
removed.
•From the inside of the electronics compartment, press the metal
socket of the network extension cable into the square hole in the rear
plate (where you removed the LAN plug) until it is held by its snap-
lock.
•Route the extension cable over the SIMMs on the CPU board and
connect it to the RJ-45 socket on the EasyLAN interface board (J2).
•From the outside, insert the thin end of the light guide through the
small hole next to the RJ-45 socket on the rear plate. Press the clear
plastic “lamp”in place. Connect the other end to the black plastic
socket (D1) on the EasyLAN interface board.
•Pull the cable tie through the hole in the upper edge of the CPU
board between the SIMMs and the RTC socket. Secure both the
extension cable and the light guide with the cable tie.
•Fit the serial number label to the printer’s rear plate below the RJ-45
socket and to the right of the memory card slot.
•Put back the front/left-hand cover. Route the cable from the display
unit above the ribbon motor. Connect the cable to connector J50 at
the upper right corner of the CPU board.
•Connect the power cord and switch on the power.
•Enter the Setup Mode and print the test label “Hardware Info”to see
if the printer detects the EasyLAN interface board. For information
on how to enter the Setup Mode, refer to the User’s Guide for the
printer in question.
•Connect the network cable to the RJ-45 socket on the printer’s rear
plate.
•Set up the network parameters. See Chapter 2.

Intermec EasyLAN Interface Kit Installation Instructions
Chapter 1 — Physical Installation
Light guide
Cable tie
RJ-45
connector
Extension cable
EasyCoder PF2/4i-series printer
EasyCoder PM4i printer
EasyLAN interface
board
Light guide
Cable tie
RJ-45
connector #T20 Torx screw and spacer
Extension cable
EasyLAN interface
board
#T20 Torx screw
and spacer

6 Intermec EasyLAN Interface Kit Installation Instructions
Chapter 1 — Physical Installation
EasyCoder PF2/4i-series printer, rear view
EasyCoder PM4i printer, rear view
RJ-45 socket
RJ-45 socket
Serial number
label
Serial number
label