Invacare 6681-5 Assembly instructions

SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. If ship-
ping damage is noted, DO NOT use. Contact Carrier/
Dealer for further instructions.
SAFETY SUMMARY
The following recommendations are made for the
safe use of the Invacare I.V. Stand:
GENERAL WARNINGS
DO NOT install this equipment without first
reading and understanding this instruction
sheet. If you are unable to understand these
Warnings, Cautions and Instructions, con-
tact a healthcare professional, dealer or
technical personnel if applicable before at-
tempting to install this equipment - other-
wise, injury or damage may occur.
SPECIFIC WARNINGS
Always inspect the I.V. stand to ensure that
it is properly positioned and is stable be-
fore using.
After ANY adjustments, repair or service
and BEFORE use, make sure all attaching
hardware is tightened securely - otherwise
injury or damage may occur.
NOTE: Model 6681-5 and 6845-5 I.V. stands are pack-
aged in pairs. There are enough parts to construct two (2)
complete I.V. stands.
Each package includes the following items:
DESCRIPTION QUANTITY
6681-5 6845-5 6845
I.V.Hanger 2 2 1
Upper I.V. tube 2 2 1
Lower I.V. tube 2 2 1
Base 2 2 N/A
Upper Base Half N/A N/A 1
Lower Base Half N/A N/A 1
Caster 10 10 4
Bolt 2 2 1
Small Steel Washer 2 2 1
Locking Washer 2 2 N/A
Black Plastic Insert 2 2 N/A
Large Steel Washer 2 2 1
Adjusting Knob 2 2 1
Washer N/A N/A 4
Locknut N/A N/A 4
Wrench N/A N/A 1
Base
Bottom of Caster
(APPLY PRESSURE
HERE)
FIGURE 1 - ASSEMBLING THE BASE
over
ASSEMBLING THE BASE (FIGURE 1)
Models 6681-5 and 6845-5
1. Place base upside down.
2. Align a caster stem with a mounting hole in the base.
3. Firmly push down on bottom of caster until caster
stem snaps into mounting hole.
NOTE: Pressure MUST be applied on the correct area or
the caster will not insert properly.
4. Repeat STEPS 2-3 for remaining four (4) casters.
Model 6845
1. Position the upper base half and lower base half as
shown in FIGURE 1.
NOTE: The lower base half has a recess in the center.
2. Install one (1) washer onto one (1) caster stem.
3. Insert caster stem UP through mounting hole in base.
4. Install locknut onto caster stem. Tighten securely us-
ing wrench provided.
5. Repeat STEPS 2-4 for remaining three (3) casters.
Caster
I.V. Stand
Assembly, Installation and Operating Instructions
Model No. 6681-5 Model No. 6845-5 Model No. 6845
Mounting
Hole
Caster
Stem
MODELS 6681-5
AND 6845-5
Upper
Base Half
Lower
Base Half
Locknut
Washer
Caster
Caster
Stem
Mounting
Hole
MODEL 6845
Recess

I.V. Hanger
Upper
I.V. Tube
Adjusting Knob
Lower I.V. Tube
Black Plastic
Insert
Base
Large steel washer
Small Steel
Washer
Lock Washer Bolt
ASSEMBLING THE I.V. STAND
(FIGURE 2)
1. Perform one (1) of the following:
A. MODELS 6681-5 AND 6845-5 -
1. Place black plastic insert into the hole pro-
vided on top of the base.
2. Insert the lower I.V. tube through the black plas-
tic insert and the base.
3. Secure the lower I.V. tube to the base with the
large steel washer, small steel washer, lock
washer and bolt. Securely tighten.
FIGURE 2 - ASSEMBLING THE I.V. STAND
Invacare Corporation www.invacare.com
USA Canada
One Invacare Way 5970 Chedwor h Way Invacare and "Yes, you can" are rademarks of Invacare
Elyria, Ohio USA Mississauga, On ario Corpora ion.
44036-2125 L5R 3T9, Canada © 2000 Invacare Corpora ion
800-333-6900 905-890-8838 Form No. 96-140 Par No. 1063112 Rev A (1) 8/2000
B. MODEL 6845 -
1. Align the upper base half and the lower base
half as shown in FIGURE 2.
NOTE: The lower base half has a recess.
2. Insert the bolt UP through wrench, small steel
washer, mounting holes in lower base half and
upper base half and large steel washer.
3. Secure the lower I.V. tube to the base with the
bolt. Tighten securely.
2. Place I.V. hanger onto the threaded end of the upper
I.V. tube. Turn clockwise to tighten.
NOTE: Ensure the I.V. hanger is screwed tightly onto the
upper I.V. tube.
3. Insert upper I.V. tube into the lower I.V. tube.
4. Insert adjusting knob into the mounting hole on the
lower I.V. tube.
5. Raise the upper I.V. tube to the desired I.V. stand height.
6. Tighten adjusting knob, by turning clockwise, at de-
sired I.V. stand height.
I.V. Hanger
Upper
I.V. Tube
Adjusting Knob
Lower I.V. Tube
Upper
Base Half
Bolt
Lower
Base Half
MODELS 6681-5 AND 6845-5
MODEL 6845
Threaded
End
Threaded
End
Wrench
Small Steel Washer
Large Steel Washer