iWave FIM-2450 User manual

FIM-2450 User Manual
July 2019
Version 1.0

ii
Document Revisions
Date
Version
Number
Document Changes
July 2019
1.0
Initial Version

iii
Table of Contents
1 Introduction ......................................................................................................................................4
2 Connectors and LEDs ........................................................................................................................ 5
3 Setting up FIM-2450 units ................................................................................................................ 9
3.1 ... Default Network Configurations.......................................................................................................9
3.2 ... Setting up steps ................................................................................................................................ 9
4 Details and Notice .......................................................................................................................... 11
4.1 ... Ethernet Cable ................................................................................................................................ 11
4.2 ... RS232 Serial Cable .......................................................................................................................... 11
4.3 ... Notice ..............................................................................................................................................14

www.iwavecomms.com
4
1 Introduction
FIM-2450 is the model name of middle-to-long range (20~30km) point-to-point video
transmission devices.
Each set of FIM-2450 contains the following it FIM-2450s
One transmitter unit, with a camera logo on it
One receiver unit, with a monitor logo on it
Two transmitter-antennas
Two receiver-antennas, which are longer than transmitter-antennas
One antenna-cable for each antenna
Power cables
Four ethernet cables, each cable has two headers, one is RJ45 header, one is
4P header to connect FIM-2450.
Four RS232-Serial cables, each has two headers, one is 6p header to connect
FIM-2450, one consists of 6 Dupont plugs.
One TX side HDMI cable with a MiniHDMI header and a MicroHDMI header
On RX side HDMI cable with a MiniHDMI header and an HDMI header
One TPlayer software Key, it’s an USB dongle

www.iwavecomms.com
5
Each kind of cable/componet is packed in its own transparent bag labeled with model
name.
The itFIM-2450s may subject to change due to different customer specific configurations
Please refer “FIM-2450 technical specification” for specifications and parameters
2 Connectors and LEDs
Front Side of Transmitter
Front Side of Receiver
One Mini HDMI plug on this side, with different logo. If the logo is a camera, then
this unit is a transmitter. If the logo is a monitor, then this unit is a receiver

www.iwavecomms.com
6
Air outlet of the internal cooling fan, you can feel strong wind near the outlet
if the unit is power on
Don’t block the air outlet when the unit is power-on, keep at least 30mm
space.
Right Side
One 4P LAN connector to connect the 4P header of the Ethernet cable. The LAN port
is for configuring FIM-2450 with TDD_COFDM software, also can be used to transmit
data (the total throughput of video/LAN/serial data should be less than the max
throughput of the wireless connection of FIM-2450)
One SMA connector, to connect an antenna
Left Side

www.iwavecomms.com
7
One 6P Serial connector, to connect RS232-Serial cable. The voltage is +-13V.
There are two serial ports in this connector. FIM-2450 transmits serial data
transparently over the wireless connection.
Six LEDs
One SMA connector, to connect an antenna. Both left side and right side SMA
connector should connect to antenna before power on
Back Side

www.iwavecomms.com
8
One power connector, to connector a power cable, the voltage range is 10~18V, Don’t
input power higher than 18V, otherwise the unit might be damaged.
No warranty for over voltage damage.
Bottom Side
An air intake is on this side, and the cooling-fan is right below the intake. After power on,
the fan should be spinning very fast. And air is flowing out through the air outlet on the
front side.
Don’t block the air intake when the unit is power-on, keep at least 20mm space

www.iwavecomms.com
9
3 Setting up FIM-2450 units
3.1 Default Network Configurations
FIM-2450 units are working as WiFi bridges, the transmitter and receiver bridge devices
connected to thFIM-2450 and forward ethernet frames transparently.
Default IP Address of FIM-2450 units
Transmitter
Receiver
192.168.55.1
192.168.55.2
IP configuration of devices connecting to FIM-2450
Transmitter side
Receiver Side
IP Address
192.168.55.X
192.168.55.X
gateway
192.168.55.1
192.168.55.2
mask
255.255.255.0
255.255.255.0
Note: TDD_COFDM software is for configuring FIM-2450, refer “TDD_COFDM software manual”
for details
3.2 Setting up steps
Connect two antennas to transmitter unit by antenna-cables
connect two antennas to receiver unit by antenna-cables
Connect power source to both units by power cables
Connect an HDMI camera/camcorder to the transmitter
Connect an HDMI monitor to the receiver
Power on both units and camera/camcorder/monitor connecting to thFIM-2450
Booting of both units takes 30~40 seconds, during booting, 6 LEDs will be flashing
many times
After approximately 30 seconds, both units will begin to search each other, LED
2,3,4 will be flashing on/off during searching by 2342….. order

www.iwavecomms.com
10
After both units found other side and established wireless connection successfully,
LED 2,3,4 will stop flashing by order, and will be showing the wireless signal strength
according by following table
LED2
LED3
LED4
Signal Strength
Index
On
On
On
5
On
On
Flashing
4
On
On
Off
3
On
Flashing
Off
2
On
Off
Off
1
Flashing by 2342….. order
No connection
If the signal strength index is above 1, the video should be transmitting. You can
watch the video from the camera/camcorder on the monitor
And the serial port data should be transmitting transparently too if there are serial
devices connecting to both units and are communicating to each other