IWILL dca200 User manual

1
DCA200-N Series Rev 1.3A FB2A518201300
Contents
Chapter 1 Quick Installation ................... 3
1.1 Layout ...................................................................................... 3
1.2 CPU setting ..............................................................................4
1.3 Jumpers .................................................................................... 5
1.4 Expansion Slots / Sockets .......................................................7
1.5 Connectors ...............................................................................9
1.6FormFactor............................................................................19
Chapter 2 Overview................................ 21
Chapter 3 Features ................................. 24
3.1 Motherboard Components Placement .................................. 24
3.2 Back Panel ............................................................................. 26
3.3 Block Diagram.......................................................................27
3.4 Specifications .........................................................................28
Chapter 4 Hardware Setup.................... 31
4.1 Before Installation.................................................................31
4.3 Install the Processor..............................................................35
4.4 Install Memory Modules ......................................................35
4.5 Install PCI Expansion Cards .................................................37
4.6 Usage of the AGP Pro slot .................................................... 38
4.7 Connect Devices and Power Supply ..................................... 39

2
Chapter 1 Quick Installation
DCA200 Series
Chapter 5 BIOS Setup............................ 53
5.1Introduction ............................................................................53
5.2 Main Menu ............................................................................ 54
5.3 Standard CMOS Features .................................................... 55
5.4 Advanced BIOS Features ..................................................... 58
5.5 Advanced Chipset Features .................................................. 62
5.6 Integrated Peripherals...........................................................64
5.7 Power Management Setup .................................................... 70
5.8PnP/PCIConfigurations........................................................ 74
5.9 PC Health Status ................................................................... 75
5.10 IWILL Smart Setting...........................................................76
5.11 Load Fail-Safe Defaults.......................................................77
5.12 Load Optimized Defaults.....................................................77
5.13 Set Supervisor / User Password Setting ............................. 78
5.14 Save & Exit Setup ...............................................................78
5.15 Exit Without Saving ............................................................. 78
Chapter 6 Power Installer CD............... 79
6.1 Software Installation..............................................................79
6.2 How to use the Power installer CD ....................................... 79
6.3 Installing Operating Systems ................................................ 81

3
Chapter 1 Quick Installation
DCA200 Series
Chapter 1
Quick Installation
Several easy installation steps will be described in this chapter to help the experienced users with
quick installation. If you are a beginner, or need to know more about this product, please refer
to Hardware Setup.
1.1 Layout

4
Chapter 1 Quick Installation
DCA200 Series
1.2 CPU setting
This motherboard is designed for Intel® Pentium® III Xeon™ processors
through a SC330 connector (330-pin slot connector) .
CPU Model L2 Vcore & Package “CPU Speed” in BIOS
Pentium II Xeon 400 512K CSRAM 2.0V, SECC 400Mhz(100x4)
Pentium II Xeon 400 1M CSRAM 2.0V, SECC 400Mhz(100x4)
Pentium II Xeon 450 512K CSRAM 2.0V, SECC 450Mhz(100x4.5)
Pentium II Xeon 450 1M CSRAM 2.0V, SECC 450Mhz(100x4.5)
Pentium II Xeon 450 2M CSRAM 2.0V, SECC 450Mhz(100x4.5)
Pentium II Xeon 500 512K CSRAM 2.0V, SECC 500Mhz(100x5)
Pentium II Xeon 500 1M CSRAM 2.0V, SECC 500Mhz(100x5)
Pentium II Xeon 500 2M CSRAM 2.0V, SECC 500Mhz(100x5)
Pentium II Xeon 550 512K CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium II Xeon 550 1M CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium II Xeon 550 2M CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium III Xeon 500 512K CSRAM 2.0V, SECC 500Mhz(100x5)
Pentium III Xeon 500 1M CSRAM 2.0V, SECC 550Mhz(100x5)
Pentium III Xeon 500 2M CSRAM 2.0V, SECC 500Mhz(100x5)
Pentium III Xeon 550 512K CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium III Xeon 550 1M CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium III Xeon 550 2M CSRAM 2.0V, SECC 550Mhz(100x5.5)
Pentium III Xeon 600 256K-on-die 2.8V, SECC 600Mhz(133x4.5)
Pentium III Xeon 600 256K-on-die 5V, SECC 600Mhz(133x4.5)
Pentium III Xeon 600 256K-on-die 12V, SECC 600Mhz(133x4.5)
Pentium III Xeon 667 256K-on-die 2.8V, SECC 667Mhz(133x5)
Pentium III Xeon 667 256K-on-die 5V, SECC 667Mhz(133x5)
Pentium III Xeon 667 256K-on-die 12V, SECC 600Mhz(133x5)
Pentium III Xeon 733 256K-on-die 2.8V, SECC 733Mhz(133x5.5)
Pentium III Xeon 733 256K-on-die 5V, SECC 733Mhz(133x5.5)
Pentium III Xeon 733 256K-on-die 12V, SECC 733Mhz(133x5.5)

5
Chapter 1 Quick Installation
DCA200 Series
1.3 Jumpers
JP1 (CMOS) Clear CMOS jumper
JP6 (PS2_SB) PS/2 power standby jumper
This jumper is used to select the power well of PS/2 ports. The feature “power on by
keyboard / mouse” can be enabled or disabled by this jumper.

6
Chapter 1 Quick Installation
DCA200 Series
JP14 (S_spkr) Speaker source select jumper
This jumper is used to select Speaker source jumper.
JP15 (LAN) LAN Enabled / Disabled jumper (DCA200-N only)
This jumper is used to enable / disable the onboard LAN chip.
.
JP16 (FLASH) FLASH protect jumper
This jumper is used to select the Flash ROM protected mode.
.pacynatuohtiw61PJevaeltonoD

7
Chapter 1 Quick Installation
DCA200 Series
1.4 Expansion Slots / Sockets
J1—J2 (CPU0—CPU1) (Slot2) Processor connectors
J3—J4 (RIMM_A0—RIMM_A1) 184-Pin RIMM Sockets
If you install two DRDRAMs and two C-RIMM, you can refer to above figure.

8
Chapter 1 Quick Installation
DCA200 Series
J5—J6 (RIMM_B0—RIMM_B1) 184-Pin RIMM Sockets
If you install four DRDRAMs, you can refer to figure.
Install memory in any combination as follows:
oteriuqertI.MARDsubmaRtceriDslennahclaudtropuusotdengisedsidraob048isihtoteuD owtsihtdna)MARDRDsruofmumixam(MARDRDfoseceip)riapa(owtmuinimllatsni evahslennahchcaE(slennahceludomyromemsubmaRhcaenillatsnidluohsMARDRDfoseceip lennahcemasotMARDRDhtobllatsniottcerroctonsitI.erugifevobaotrefer,)MMIRowt draob048isihtotnorewoponesuaclliwsihT.lennahcrehtoehtnidetalupopMMIR-ChtiwMMIR .ezisyromememashtiwdnaemitariapaebdluohsMARDRDllatsniyllufsseccusoT.
J12—J15 (PCI 1—PCI 4) PCI expansion slots (32bit / 33MHz)

9
Chapter 1 Quick Installation
DCA200 Series
J16—J17 (PCI 64_1—PCI 64_2) PCI expansion slots (64bit / 66MHz)
J27 (AGP PRO) 4xAGP AGP Pro Slot
1.5 Connectors
J28 (IDE0) Primary ATA/66 IDE channels
J29 (IDE1) Secondary ATA/66 IDE channels

10
Chapter 1 Quick Installation
DCA200 Series
J30 (FDC) Floppy connector
J37 ATX power connector

11
Chapter 1 Quick Installation
DCA200 Series
J37A (WTXA) WTX 24PIN power connector
J37B (WTXB) WTX 22PIN power connector
J37C (WTXC) WTX 8PIN power connector

12
Chapter 1 Quick Installation
DCA200 Series
J1A & J1B Fan connectors for Dual Retention Module (4cm type Fan)
J2A & J2B Fan connectors for Dual Retention Module (4cm type Fan)

13
Chapter 1 Quick Installation
DCA200 Series
J39 (FCPU 0) & J40 (FCPU 1) & J41 (FSYS)
There are three fan connectors on this motherboard. The J39 (FCPU0) is designed to
support CPU fan; the J41 (FSYS) is for system fan used and the J40 (FCPU1) is designed
to support CPU fan.
J39A (TCPU 0) & J40A (TCPU 1) & J41A (TSYS)
This motherboard has three temperature sensor headers. You can connect the tempera-
ture sensor to these headers in order to monitor and CPU the temperature.These three
connectors without orientation limit.

14
Chapter 1 Quick Installation
DCA200 Series
J42 Chassis Intrusion Connector (CASE)
The connector is for a chassis designed for chassis intrusion detection.
J43
This connector is composed of all the headers that may be connected to the front
panel of the chassis.

15
Chapter 1 Quick Installation
DCA200 Series
J44 (SB_LINK)
This is the SB_LINK connector. In order to enabling users to play real-mode DOS
games. Connect the cable provided by PCI sound card to this connector.
J45 (IR)
This connector is designed for the SIR/FIR/CIR devices.

16
Chapter 1 Quick Installation
DCA200 Series
J46 (WOL)
This is the Wake-on-LAN connector. In order to wake up the system through a plug-in
network card, the card must provide a high active wake signal.
J47 (WOM)
This connector can be connected to MR card or internal modem card to provide the
ability of power on by modem device.
J48 (SMBUS)
This connector provides the connectivity of SMBUS utilization.

17
Chapter 1 Quick Installation
DCA200 Series

18
Chapter 1 Quick Installation
DCA200 Series
J53 (AUX_IN) & J54 (CD_IN)
These connectors allow you to receive stereo audio input from such sound sources as a
CD-COM, TV tuner or MPEG card.
J31 External COM1 connector
J32 External COM2 connector
J33 External Parallel connector
J35 External PS/2 mouse & keyboard connector
J58 External Dual USB & RJ45 connector
J56 External Game / Line-in / Line-out / MIC connector

19
Chapter 1 Quick Installation
DCA200 Series
1.6 FormFactor

20
Chapter 1 Quick Installation
DCA200 Series