J D Williams 2 Door 1 Shelf Mirrored Robe User manual

Assembly Instructions - Please keep for future reference
Width - 68.5cm
2 Door Robe
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 49.8cm
Height - 180.0cm
Rev A- 10/04/2019
001 xx 9415
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Bottom x 2 (65.1x46.2cm)
1229
Left End Panel
(178.4x49.6cm)
1231
1228
Plinth x 2 (65.1x7.6cm)
0435
Back Rail (65.1x12.4cm)
0677
Right End Panel
(178.4x49.6cm)
1232
Backpanel (170.8x66.0cm)8024
Door x 2
(170.0x32.1cm)
Hanging rail (64.5cm Long)
740006003
Top Rail (62.4x6.0cm)
7194
Top (68.5x49.8cm)
0843

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 24
Code 760001103
Metal dowel x 24
Code 760003004
ABC
E
Drill
DF
H
GI
J
Panel pin x 8
Code 760001012
Panel pin guide x 1
Code 684004501
Hanging supports x 2
Code 680006003
Hingeplate x 6
Code 653006000
12mm screw x 2
Code 690001099
12mm screw x 16
Code 690001008
Support bracket x 1
Code 760001901
Bradawl
KL
18mm bolt x 2
Code 700002021
M
Panel Holder x 5
Code 680003505
N
25mm Screw x 2
Code 690001021
Fully cranked 26mm
hinge x 6
Code 652001120
Handle x 2
Code 640391127

Exploded View
4
7194
1229
8024
1229
0843
1228
1228
1231
1232
0677
0435

Assembly Instructions
5
0435
B
B
B
0843
0843
7194
A
Step 1
B
x4
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
B
N
N
N
N
x2
Fitting dowels to top
panel.
Connect the top rail
to the top panel.
Fitting cams to the
plinth and back rail.
Step 2
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
A
x12
A
A
A
0677
A
A
A
A
Insert 4 metal dowels
into the top panel 0843
Using 2 screws secure
the top rail to the
top panel .
0843
7194
A
Insert 4 cams into
the plinth panel
Repeat on both of the
plinth panels.
0435
Step 3
A
Insert 4 cams into
the back rail panel 0677
B
X 2

Assembly Instructions
6
Step 4
H
x3
F
x2
C
x1
Insert 3 hinge plates
into the left end panel
.
Insert 2 screws through
the holes in the hanging
rail support .
Note: A bradawl may be
required when attaching
the hanging rail support
to create the lower hole.
H
F
C
1231
Step 5
H
H
H
F
C
1231
Fitting hanging rail
support & hingeplates
to left end.
Fitting cams & dowels
to the left end panel.
B
x10
A
x2
Insert 10 metal dowels
and 2 cams into
left end panel
BA
1231
B
B
BBB
BB
A
1231
A
B
B

Assembly Instructions
7
Step 6
B
x10
A
x2
Step 7
B
B
B
B
B
B
BB
BB
Fitting cams & dowels
to the right end panel.
Insert 10 metal dowels
and 2 cams into
right end panel
BA
1232
A
x8
Step 8
Fitting cams the
bottom panel.
Insert 4 cams into the
bottom panel
Repeat on both of the
bottom panels.
A
1229
1232
A
A
A
A
1229
A
A
Fitting hanging rail
support & hingeplates
to right end.
Insert 3 hinge plates
into the right end panel
.
Insert 2 screws through
the holes in the hanging
rail supports .
Note: A bradawl may be
required when attaching
the hanging rail support
to create the lower hole.
H
F
C
1232
H
H
H
H
x3
F
x2
C
x1
F
F
C
1232
X 2

Assembly Instructions
8
Step 9
Attach hinges to the
2 doors
A: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
B: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
I
I
C: Secure hinges to
doors using screws .
I
F
I
x6
F
x12
1228
F
F
F
F
F
F
A
B
C
I
I
I
1228
1228
Bradawl
90
Correct
98
Incorrect

Assembly Instructions
9
Step 10
Connect the dowels in
the left end to the
cams in the plinths ,
the bottoms and
the back rail
Connect left end to
the plinths, bottoms
and back rail.
Step 11
1231
0435
1229
0677
Ensure plinth is
not overhanging.
Ensure plinth sits
flush.
1231
0435
1229
1229
0677
Connect the dowels in
the right end to the
cams in the plinths ,
the bottoms and
the back rail
Connect right end to
the plinths, bottoms
and back rail.
1232
0435
1229
0677
We recommend that 2
people for this step, to
hold the back rail in
place.
We recommend that 2
people for this step, to
hold the back rail and
plinth in place.
Turn cams 180 degrees
to lock.
0435
1229
1229
0677
1232
Turn cams 180 degrees
to lock.

Assembly Instructions
10
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Measure to
external corners
Squaring up the unit.
Ensure a tape
measure is used
to square up unit!
Important:
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Step 12
Connect right end and
left end to the top
panel.
Connect the dowels in
the top panel to the
cams in right end
and the left end
0843
1231
1232 0843
1231
1232
8024
XX
YY
YY
XX
Slide back panel into
the unit.
Slide the back panel into
the grooves in the left &
right end panels and the
top panel.
Step 13
Lay the unit on
its front.

Assembly Instructions
11
Step 11
Step 14
Secure back panel in
the unit.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
E
G
E
x8
G
x1
M
x5
E
G
8024
8024
Step 15
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves.
Once inserted fully,
tighten the screws in the
stability blocks.
M
8024
M
M
M
M
M
M

Assembly Instructions
12
Step 16
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
Locate hanging rail
onto brackets already
attached. The hanging
rail just slots onto the
brackets.
Locate hanging rail(s)
D
x1
J
x2
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Always ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING

Assembly Instructions
13
Step 17
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Hanging doors
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
The doors can be fitted
to either side depending
on your preference.
Repeat the process on
the remaining door.
B
B
B
Underside view
Ensure the underside of screw
B slides into slot on hingeplate.
Hinge correctly attached to
hingeplate.
Hinge incorrectly attached to
hingeplate.
Diagram 1
Diagram 2
Diagram 3
A
B
L
K
L
x2
K
x2
c: Fit 1 bolt through
the pre-drilled hole in the
door , and connect
to the handle .
K
L
1228

Assembly Instructions
14
Step 18
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)