Jøtul F480 User manual

Jøtul F 480
UK - Installation and operating instructions 3
FR - Manuel d’installation et d’utilisation 20
ES - Instrucciones para instalación 37
IT - Manuale di installazione ed uso 54
NL - Installatie- en montagehandleiding 71
Jøtul F480
Manual Version P05
Jøtul F 481 Jøtul F 483
The manuals which are enclosed with the product must be kept throughout the product’s entire service life.Les
manuels fournis avec le produit doivent être conservés pendant toute la durée de vie du produit. I manuali inclusi
con il prodotto vanno conservati per l’intera durata di vita del prodotto.

2
EU no. 215/1186 - 24/04/2015
Datasheet / Fiche Technique / Ficha técnica /
Scheda dati / Datasheet / Datenblatt
Requirements / Exigences / Requisitos / Requisiti /
Vereisten / Forderungen
Supplier /
Fabricante /
Fornitore /
Vereisten /
Lieferant:
Jøtul AS
Product models
Produits concernés
Modelos
Modelli
Product modellen
Varianten der Feuerstelle
Jøtul F 480 Series:
Jøtul F 481
Jøtul F 483
Energy efficiency class / Classe énergétique / Clase de
eficiencia energética / Classe energetica / Energie
efficiëncy klasse / Energieeffizienz-Klasse
A
Direct heat output / Puissance réelle de sortie / Potencia
calorifica emitida / Emissione di calore diretta / Directe
warmte afgifte / Nennwärmeleistung
6,0 kW
Energy efficiency index / Index de rendement énérgétique/
Índice de eficiencia energetica / Indice di efficienza
energetica / Energie efficiëncy index / Energieeffizienz-
Index
99,8
Efficiency at nominal heat output / Rendement à
puissance nominale / Eficiencia al rendimiento nominal /
Efficienza alla potenza nominale / Efficiency bij nominale
warmte afgifte / Wirkungsgrad bei Nennheizleistung
75 %
xAny specific precautions that shall be taken when the
local space heater is assembled installed or
maintained.
xToutes les précautions spécifiques doivent être prises
lors de l’assemblage, l’installation ou l’entretien de
l’appareil.
xCualquier precaución específica que deba tenerse en
cuenta durante el montaje, instalación o
mantenimiento del equipo de calefacción
xPrecauzioni specifiche da prendere quando il
riscaldatore viene assemblato, installato o mantenuto
in uno spazio.
xEventuele specifieke voorzorgsmaatregelen die
worden genomen wanneer de plaatselijke
ruimteverwarming wordt gemonteerd, geïnstalleerd of
onderhouden.
xBesondere Maßnahmen bei Montierung, Installation
und Wartung.
xFire safety precautions such as safety distances when
installing, national standards, local codes and
regulations. See the Instructions manual.
xLes précautions d'incendie telles que les distances de
sécurité lors de l'installation, le suivi des normes, les
codes locaux et les règlementations nationales. Veuillez
lire le manuel d’installation.
xPrecauciones frente a incendios como distancia de
seguridad en la instalación, estándares nacionales,
códigos locales y reglamentos. Lea el manual de
instalación.
xPrecauzioni per la sicurezza antincendio come le distanze
di sicurezza durante l'installazione, le normative nazionali
e locali. Leggere il manual.
xBrandveiligheidsmaatregelen, zoals veiligheids-
afstanden bij installatie, nationale normen, lokale
codes en voorschriften. /HHVௗGHLQVWDOODWLHKDQGOHLGLQJ
xFür brenntechnische Verhältnisse, wie z.B.
Aufstellbedingungen und nationale Forderungen.
Siehe die Montage- und Bedienungsanleitung.

3
ENGLISH
Table of contents
1.0 Technical data ......................................... 3
2.0 Relationship to the authorities.................. 3
3.0 Safety ....................................................... 4
4.0 Installation ............................................... 7
5.0 Daily Use................................................ 13
6.0 Maintenance........................................... 14
7.0 Servicing ................................................ 15
8.0 Operational problems - troubleshooting .... 18
9.0 Optional Extras....................................... 18
10.0 Recycling................................................ 19
11.0 Guarantee terms ................................... 19
On all our products there is a label
indicating the serial number and
year. Write this number in the
place indicated in the installation
instructions.
Always quote this serial number
when contacting your retailer or
Jøtul.
les combustibles recommandés.
Respectez les consignes d'utilisation. Utilisez uniquement
Verwenden Sie nur empfohlenen Brennstoen.
Montage- und Bedienungsanleitung beachten.
Follow user`s instructions. Use only recommended fuels.
standard
Certicate/
The appliance can be used in a shared ue.
Minimum distance to adjacent combustible materials:
Emission of CO in combustion products
Lot no: Y-xxxx, Year: 200x
Manufacturer:
N-1602 Fredrikstad
Norway
Jøtul AS
POB 1441
Sweden
EUR Intermittent
Nominal heat output
Norway
Country
Operational type
Fuel type
Operation range
Eciency
Klasse II
Classication
Standard
Flue gas temperature
Room heater red by solid fuel
Product:
Jøtul
SP Sveriges Provnings- och
221546
Forskningsinstitut AB
SP Swedish National
Testing and Research
Institute
:
Approved by
:
:
:
:
:
:
:
Minimum distance to adjacent combustible materials:
OGC SP
EN
Lot no. Pin.
1.0 Technical data
Material: Cast iron
Finish: Black paint
Type of fuel: Wood
Max. log length: 30 cm
Smoke outlet: Top, rear
Flue pipe dimension: Ø 150 mm
Outside air connection: Alu. flex - Ø 80 mm
Product weight:
Burn chamber: 119 kg
Base, cast iron 46 kg
Pedestal, cast iron 34 kg
Cast iron sides 33 kg
Optional extra Floor plates, Outside air
connection, Rotating set for
the Jøtul F 483
Product dimensions, distances: See Fig. 1
Technical data in acc. with EN 13240
Nominal heat output: 6,0 kW
Flue gas mass flow: 6,0 g/s
Recommended
chimney draught: 12 Pa
Efficiency: 75%@6 kW
CO emissions (13% O2): 0,08%
Flue gas temperature: 315oC
Dust: < 20mg/m3n@13%O2
Burn time: 2.2 kg/h
Operational type: Intermittent
Intermittent combustion here means normal use of a fireplace,
i.e. add more fuel as soon as the fire has burned down to
embers.
2.0 Relationship to the
authorities
• Installation of a fireplace must be carried out in compliance
with national laws and regulations. All local ordinances,
including those that refer to national and European
standards, must be complied with when products are
installed.
• The installation can only be put into use after it has been
checked by a qualified inspector.
• Contact your local building authorities before installing a
new fireplace.
Register your fireplace at www.jotul.com
for a 25-year warranty.

4
3.0 Safety
NB! To guarantee optimal performance and safety, Jøtul
recommends that its stoves are fitted by a qualified
installer (see www.jotul.com for a complete list of dealers).
Any modifications to the product by the distributor, installer or
consumer may result in the product and safety features not
functioning as intended. The same applies to the installation of
accessories or optional extras not supplied by Jøtul. This may
also be the case if parts that are essential to the functioning and
safety of the fireplace have been disassembled or removed.
In all these cases, the manufacturer is not responsible or liable
for the product and the right to make a complaint becomes null
and void.
3.1 Fire Prevention Measures
There is a certain element of danger every time you use
your fireplace. The following instructions must therefore be
followed:
• The minimum safety distances when installing and using
the fireplace are given in fig. 1.
• Ensure that furniture and other flammable materials are
not too close to the fireplace. Flammable materials should
not be placed within 1 metre of the fireplace.
• Allow the fire to burn out. Never extinguish the flames with
water.
• The fireplace becomes hot when lit and may cause burns
if touched.
• Only remove ash when the fireplace is cold. Ash can
contain hot embers and should therefore be placed in a
non-flammable container.
• Ash should be placed outdoors or be emptied in a place
where it will not present a potential fire hazard.
In case of chimney fire:
• Close all hatches and vents.
• Keep the firebox door closed.
• Check the loft and cellar for smoke.
• Call the fire service.
• Before use after a fire an expert must check the fireplace
and the chimney in order to ensure that it is fully functional.
3.2 Floor
Foundation
You need to make sure the foundation is suitable for a fireplace.
See “1.0 Technical Data” for specified weight.
We recommend the removal of any flooring that is not attached
to the foundation (“floating floors”) beneath the installation.
Requirements for protection of wooden
flooring beneath the fireplace
The product has integrated floor protection and may therefore
be placed directly on a wooden floor.
Jøtul recommends that any flooring made of combustible
material, such as linoleum, carpets, etc. should be removed
from under the floor plate.
Requirements for protection of
inflammable floors in front of the fireplace
The front plate must comply with national laws and regulations.
Contact your local building authorities regarding restrictions
and installation requirements.
3.3 Walls
Distance to walls made of combustible material - see fig.
1a
Distance to combustible wall protected by firewall: See
fig. 1b
The fireplace may be used with an uninsulated flue pipe
provided the distances between the fireplace and walls made
of combustible materials are as shown in fig. 1a.
NB: Pay particular attention to this when using revolving
pedestal!
ENGLISH

5
ENGLISH
Fig. 1 a
Jøtul F 481 Jøtul F 483 Brennbar vegg
Min. distance to furniture / combustible material = 900 mm
900168-P02
740
1180
440
1025
145
145
154
1034
1189
460
230
128
466
Y
X
Min. 1950
350
583
120
*100
360
*340
120
*100
360
*340
120
*100
350
*330
580
*560
350
583
360
*340
120 *100
739
509
Min. distance to combustible wall
Distance to combustible wall with rotating pedestal
* Semi-insulated chimney / shielded flue pipe
Min. measure floorplate X/Y = Acc. to national standards and regulations
Hole in floor for external air supply Ø 80 mm connection Jøtul F 483
Hole in floor for external air supply Ø 80 mm connection Jøtul F 481
Combustible ceiling
Jøtul F 483 with rotating set

6
Fig. 1 b
Jøtul F 481 / F 483
100
450
50
1110
433
200
660
50
280
1330
665
433
200
50
280
825
825
50
640
410
290
725
50
640
725
410
900168-P02
Min. distance to combustible wall protected by firewall
External
Integrated
Combustible wall
Firewall
460
50
ENGLISH

7
ENGLISH
Air supply
The amount of combustion air for Jøtul’s products is approximately
20-40 m3/h. The outside air connection may be fitted directly to
the Jøtul F 480 through:
• The base/pedestal or
• through a flexible supply hose from the outside/chimney
(only if the chimney has its own duct for external air) and to
the product's outside air connector.
Fig. 2A, through an outside wall
Fig. 2B, through the floor and ground plate
Fig. 2C, through the floor and basement
Fig. 2D, indirectly through an outside wall
4.0 Installation
NB: Check that the fireplace is undamaged before installation
begins.
NB: The product is heavy! Ensure you have help when
positioning and installing it. Make sure the product does
not topple over.
NB: Do not place anything on the top plate of the stove as this
could cause permanent damage to the paint/enamel.
NB: Read the Installation and Operating instructions carefully
before installing the fireplace!
4.1 Prior to installation
The standard product comes in three or more consignments
One with the burnchamber, one with the base or pedestal and
side panels.
You will need the following tools to install the product: Spirit
level, ratchet with 10 mm and 13 mm sockets,Torx T 20 and
hex keys with 5 mm socket.
Fig. 3
A
B
C
1. Remove the packaging (cardboard and wooden frame) and
spread the cardboard out on the floor behind the fireplace.
Remove the white foam plastic in the top.
2. Remove the screws attaching the burnchamber to the
transport pallet.
3. Leave the stove standing on the transport pallet.
4. Remove the top plate (A) with the top grate (B).
5. Remove the gloves and bowl from the ash pan. Place the
bowl on the top grate right up to the end if the flue pipe is
rear-mounted.
6. Check that the control handles (C) move freely.

8
4.2 Installation
External air supply through the base
Through the floor
1. NB! If connecting the Flex Hose through a hole in the floor,
do not knock out the removable cover plates (Fig. 5 A).
Through the rear outlet in the base
Fig. 4
A
B
2. If connecting a flex hose through the rear outlet of the
base, the shelf (A) and the internal back plate (B) must be
removed first.
Fig. 5
A
3. If connecting a flex hose (Ø 80 mm) for external air supply
to the external air connector beneath the burn chamber,
the removable cover plates (A) must be knocked out first
Installation of base/pedestal on the
burnchamber
Fig. 5
4. Carefully lay the stove down on its back. Rest the stove on
a pallet and three packaging frames.
Fig.6
B
B
B
B
Fig. 7
5. Before installing the base, the shelf (Fig. 4-A) and internal
back plate (Fig. 4-B) must be removed. Push the base
up to the burn chamber and secure it firmly with the four
screws (M8 x 25 mm) and washers provided. See Fig. 7 B.
ENGLISH

9
ENGLISH
Fig. 9
AA
AA
6. Loosen the height adjustment screws slightly (A) beneath
the product so that they can be screwed by hand. NB: If the
optional glass floor plate is to be installed, the base must
be raised approximately 8 mm offthe floor so that it can be
pushed under the front edge of the base.
Fig. 10
A
7. Carefully remove the wooden pallet.
8. Place a packaging frame (A) crosswise underneath the
base/pedestal/leg and cardboard packaging in front of/
beneath the product to prevent it from making marks on
the floor. Carefully raise the stove and stand it in its proper
place (fig 1). Remember to position it straight above or
behind the external air supply, whichever is applicable.
9. Place the top plate (fig. 3 A) temporarily in place and
level the fireplace. If the stove is not standing level, adjust
the screws shown in fig. 9 A until the product is perfectly
straight.
10. If the control handles (Fig. 3C) are difficult to pull out, see
step 4.6
4.9 Location of approval label
The approval label must always be affixed to the wire and
positioned as illustrated in fig. 11.
Fig. 11, Base
A
Fig. 11, Pedestal
A

10
Installation with external air supply
Fig. 12 - Base
10 cm
Fig. 12 - Pedestal
10 cm
1. Attach the hose to the external air connector using a
hose clip (NB! Do not fit a hose clip onto the Jøtul F 483
pedestal with a rotating set as this prevents the set from
rotating). NB! Make sure the hose is long enough so that
joints are not necessary. The external air hose insulation
ends approx. 10 cm below the burn chamber.
2. Refit any parts that have been removed from the product.
4.3 Chimney and flue pipe
• The fireplace must only be connected to a chimney and
flue pipe approved for solid fuel fireplaces with flue gas
temperatures as specified in «1.0 Technical Data».
• The cross-section of the chimney must be designed to fit
the fireplace. Use «1.0 Technical Data» to calculate the
correct chimney cross-section.
• The chimney must be connected in accordance with the
installation instructions of the chimney supplier.
• Before a hole is made in the chimney, the product should
be test-mounted in order to correctly mark the position of
the fireplace and the hole in the chimney. See fig. 1 for
minimum dimensions.
• Make sure that the flue pipe rises all the way up to the
chimney.
• With a rear outlet, use a flue pipe bend with a sweep hatch
to allow sweeping.
• Please note that it is extremely important for connections
to have a degree of flexibility. This is to prevent any
movement in the installation leading to the formation of
cracks.
• For recommended chimney draught, see «1.0 Technical
Data». For flue pipe dimensions with the relevant cross-
section, see “1.0 Technical Data”.
NB! The minimum recommended chimney length is 3.5 m
from the flue pipe insert. If the draught is too strong, a flue
pipe damper can be installed and used to reduce the draught.
ENGLISH