jbc TE Series User manual

TE
PRECISION
HOT AIR STATION
www.jbctools.com

2
JT / PRECISON HOT-AIR
CONTROL UNIT TE-SA
STAND
TE-TB
(100V / 120V / 230V)
HEATING SET
0008752
EXTRACTOR STAND *
TN9209 ø3
TN9208 ø4
TN9080 ø5
NOZZLE
0930110
SUCTION CUPS *
0932330
SUCTION TUBE *
T2050 ø20
T2250 ø40
TRIPOD*
POWER CORD
* These accessories not supplied with TE-2QB / TE-1QB / TE-9QB stations
Protector
P2220 (32)
P2230 (48)
P2235 (24)
P4000 (44)
P4010 (60)
Extractor
E2184
E2064
E2052
TE
PRECISION
HOT AIR STATION
www.j bctools.co m

3
INSTALLATION
Power cord
socket
Equipotencial
connection
Pedal 0964551
(NOT INCLUDED)
(ON / OFF hot air)
DESCRIPTION
Display
USB connector to PC:
- Update station software
- Create graphs of the soldering process
- Manage and monitor parameters via PC
Function keys
Connectable tools:
JT-T2A / JT-T1A
TE-TB
Heating element
Hot Air switch
(ON / OFF)
Suction
Tube
Main switch
Heater inlet
Vacuum inlet for tripods
and extractors
Activation of
suction pump

4
CONTROL SCREEN / MANUAL MODE
CONTROL SCREEN / PROFILE MODE
Decrease & move down
Decrease profile number
Increase & move up
Increase profile number
Access Menu
&
Confirm Selection
Access Menu
(pess key 2 secondes)
Temp º C
Temp º C
Air %
º C
Time to stop 45 seconds
Profile 8
Power 70%
400
380
80
Selected temperature
Current temperature
% Instant power supplied to heater
Selected profile
Current temperature
Selected flow
Graph of selected profile
Remaining time
400ºC Select
Air 100%
Time 125s.
You can switch between operating modes (Manual Mode / Profiles Mode) by pressing the “increase” and
“decrease” keys simultaneously for 2 seconds. (Only if mode profiles is ON)
PRESS Key 2 seconds
to access Menu

5
Select
Profile
Step 4
Time 20
Temp 450
Air 100
º C
º C
Edit Profile
Edit Profile 8
8
ORIGINAL PIN: 0105
Main menu
Settings
Counters
1 Reset settings
2 Station Settings
3 Profile Settings
4 Counters
5 Program version
1 Temp unit Celsius
2 Maximum temp 450
0
C
3 Minimum temp T OFF
4 Fix temp 400
0
C
5 Max air 100%
6 Min air 10%
7 Fix air 40%
8 Time to stop 120 sec
9 Beep ON
10 Pop up ON
11 Change PIN
1 Station ON hours 0
2 Works hours 0
3 Works cycles 0
Exit
Back
Back
Exit
SETTINGS
*
* Selecting Tmin to “T OFF” allows
for blowing at ambient temperature.
Profile settings
1 Profiles
2 Edit Profile
3 Copy profile
Exit

6
DESOLDERING PROCEDURE
1. Position suction cup. 2. Hot-air melts solder. 3. IC pops up automatically.
EDIT PROFILE
This option allows you to edit or create a profile.
First , you must select the profile to edit and then modify the points that make up the profile.
Each profile is composed of 9 points, each point is formed by three parameters:
1. Time (seconds)
2. Temperature (°C / °F)
3. Flow rate (%)
You can delete the last point of the profile by selecting “-----” in the time parameter.
It should be taken into account that the regulation range permitted by the station is between 150°C and
450°C, whereby it is not possible to create temperature ramps between room temperature (Toff) and
150°C.
The station can store up to 25 temperature profiles.
The first three profiles are edited as an example.
COPY PROFILE
This option allows you to copy a profile.
You must select the profile source and the destination profile where it will be copied.
DELETE PROFILE
This option will allow you to delete a profile previously selected.

7
MAINTENANCE
CHANGING THE HEATING SET
1. Ensure that the tool is off.
2. Use a wrench to unscrew the connector seal.
REPLACING THE HEATING ELEMENT
Follow this process inverted to re-connect the heating element.
Only perform this operation when the tool is stopped and the heating element set is cold.
1. Untighten screw.
2. Separate the heating element from the heating set’s handle.
3. Connect new heating element, pushing it’s extreme.
4. Insert screw to aviod air-loss witch could reduce the heating element’s lifetime.
3. Pull back the seal.
4. Pull connector from socket to disconnect heating set.
5. Follow steps in reverse to connect the heating set.
0012374
(230V -100V -120V)
Heating element
0012697
Handle
TE-TB
(100V-120V -230V)
Heating set

WARRANTY
JBC’s 2 years warranty guarantees this equipment against all manu-
facturing defects, covering the replacement of defective parts and
all necessary labour.
Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased enclosing this
fully filled in, sheet.
www.jbctools.com
SERIAL Nº
STAMP OF DEALER
DATE OF PURCHASE
0012881-0313
TECHNICAL SPECIFICATIONS
- Temperature selection from room temperature to 450°C (850ºF) and cool mode (can be used to blow air at room
temperature).
- Ambient Operating Temperature: 10 to 40ºC (50-104ºF)
- Output Peak Power: 300W.
- Air flow regulation: 5-20 l/min.
- Vacuum: 30% / 228 mmHg / 9 inHg
- TE-2B 230V 50/60Hz. Input fuse 4A.
- TE-1B 120V 50/60Hz. Input fuse 8A.
- TE-9B 100V 50/60Hz. Input fuse 8A.
- Total weight of unit: 2.3Kg (5.1lb)
- Complies with CE standards on electrical safety, electromagnetic compatibility
and ESD protected housing “skin effect”.
- RoHS compliant.
- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.
This product should not be
thrown in the garbage.