John Lewis Tom Floor lamp User manual

IL4085
Recommended bulb
1 x 6-9 Watt E27 (ES) energy efficient LED GLS bulb
Or
1 x 42W E27 eco halogen GLS bulb
Bulb not included
Specification
Max power: 42W
Voltage: 220~240V, 50Hz
IP20
Weight 3.8Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal house-hold
waste and it should be recycled. John Lewis does not operate in store take back, but
as members of the Distributer Take Back scheme have funded the development and
upgrade of recycling facilities across the UK. Please take it to your nearest collection
facility or for further details contact your local council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
[e-mail]
Trouble shooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 01 09/18
User manual
Tom Floor lamp

IL4085
Thank you for purchasing this Tom floor lamp. Please read the instructions carefully
before use to ensure safe and satisfactory operations of this product.
Please keep this instruction for future reference.
Warnings!
The supply cable runs through the inside of this product. Take care not to place
undue stress on the cable whilst unpacking to prevent the possibility of a poor
connection.
If you are in any doubt consult a person competent to give advice on the
assembly of electrical equipment.
If the external flexible cable of the lamp is damaged it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in
order to avoid a hazard.
To prevent electrocution switch off at the mains supply before assembling or
maintaining this fitting. Ensure the plug is not connected to any power supply and
read instructions before assembly.
Always be sure to use the correct type and wattage of bulbs as indicated on the
fitting. Never exceed the wattage stated.
When changing the bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulbs from John Lewis or established brand of the same type and
compatibility.
Parts list
Part List
Qty
Part List
Qty
A
1
B
1
C
1
D
1
E
1
Assembly
Never assembly your appliance on a wet, freshly painted surface. Ensure to off at
the mains supply before assembling or maintaining this fitting.
Step 1
Unpack the product and remove all packaging. Be careful
not to scratch the surface of the product whilst removing
the wrapping.
Lay the product out on the floor. If the floor is not carpeted
please cover it with a soft cloth to avoid damage to the
flooring and surface of the product. Assembly should take
place with the product lying flat.
Screw the centre pole onto the upper lamp holder section
ensuring that the lamp holder section is kept still and that
the pole is threaded on ensuring that the cable does not
twist.
Step 2
Screw the lower pole onto the centre pole ensuring that
the centre pole is kept still and that the pole is threaded on
ensuring that the cable does not twist.
Gently pull any excess supply cable through the small hole
in the base until it meets the pole assembly.
Insert the assembled poles into the receiving collar on the
base section. Insert and fully tighten the two grub screws at
the rear of the floor lamp using the hex key provided to
secure the assembly in place.
Stand the floor lamp upright and ensure all the assembled
parts are fully tightened.
Loosen the screw on the saddle cable clamp located inside the base section.
Place the electrical cable from the floor lamp under the clamp and retighten to
lock the cable in place. Take care not to damage the wiring. Attach the foam pad
onto the base of the product to protect the floor when in use.
Step 3
To fit shade: Remove the shade ring from lamp holder, fit
the shade and replace shade ring to secure in place.
Take care not to overtighten as this may cause damage
to the fitting.
Fit the bulb, type and wattage as indicated on the
fitting (bulb not supplied). The wattage indicated must
not be exceeded.
Floor lamp is now ready for use.
Step 1
Step 2
Step 3