John Lewis IL4248 User manual

IL4248
Recommended bulb
1 x 6-10 Watt E27 energy efficient LED bulb
or
1 x 42 Watt E27 eco halogen bulb
Bulb not included
Specification
Max power: 60W
Voltage: 220~240V, 50Hz
IP20
Weight 2.2Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal house-hold
waste and it should be recycled. John Lewis does not operate in store take back, but
as members of the Distributer Take Back scheme have funded the development and
upgrade of recycling facilities across the UK. Please take it to your nearest collection
facility or for further details contact your local council or visit www.recycle-more.co.uk.
Trouble shooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 01 02/20
User manual
SPINDLE WOOD
FLOOR LAMP

IL4248
Thank you for purchasing this Spindle Wood floor lamp. Please read the instructions
carefully before use to ensure safe and satisfactory operations of this product.
Please keep this instruction for future reference.
Warnings!
The supply cable runs through the inside of this product. Take care not to place
undue stress on the cable whilst unpacking to prevent the possibility of a poor
connection.
If you are in any doubt consult a person competent to give advice on the
assembly of electrical equipment.
If the external flexible cable of the lamp is damaged it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in
order to avoid a hazard.
To prevent electrocution switch off at the mains supply before assembling or
maintaining this fitting. Ensure the plug is not connected to any power supply and
read instructions before assembly.
Always be sure to use the correct type and wattage of bulbs as indicated on the
fitting. Never exceed the wattage stated.
When changing the bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulbs from John Lewis or established brand of the same type and
compatibility.
Parts list
Part List
Qty
Part List
Qty
A
1
B
1
C
1
-
Assembly
Never assembly your appliance on a wet, freshly painted surface. Ensure to off at
the mains supply before assembling or maintaining this fitting.
Step 1
Unpack the product and remove all packaging. Be careful
not to scratch the surface of the product whilst removing the
wrapping.
Lay the product out on the floor. If the floor is not carpeted
please cover it with a soft cloth to avoid damage to the
flooring and surface of the product. Assembly should take
place with the product lying flat.
Attach the centre pole onto the lampholder section by
rotating into place. Ensure the lampholder section is kept still
rotating only the centre pole. Take care not to allow the
electrical cable to twist.
Step 2
Gently pull the excess cable out of the base until the
assembled poles meet the base.
Turn the base section onto the centre section. Keep the
poles parallel to avoid cross threading. Keep the upper
poles stationary and only rotate the base section.
Ensure all of the excess cable is removed from the base and
the cable is not twisted.
Step 3
Stand the floor lamp upright and ensure all the assembled
parts are fully tightened.
Fit the shade by first removing the shade ring from the lamp
holder. Position the hole in the centre of shade over the
lamp holder and replace shade ring to secure shade in
place.
Fit the bulb, type and wattage as displayed on the fitting.
The stated wattage must not be exceeded.
Floor lamp is now ready for use.
Step 1
Step 2
Step 3