Jura IMPRESSA F70 User manual

IMPRESSA F70 / F707
Instructions for use

Legend:
䡲DISPLAY: serves as information.
䡲DISPLAY: please follow the instructions shown. = Note = Important = Tip

Fig. 1 Fig. 2 Fig. 3 Fig. 4
Fig. 6 Fig. 7 Fig. 9 Fig. 10
Fig. 11 Fig. 12 Fig. 13 Fig. 14
Fig. 16
Fig. 5
Fig. 8
Fig. 15
Fig. 17 Fig. 18

Temp. max.
Fig. 19
Fig. 21
Fig. 20
Temp. min.

Control elements
1. Rotary Switch
2. Illuminated ring
3. ON / OFF symbol
4. 1 LARGE CUP symbol
5. 1 COFFEE symbol
6. 1 ESPRESSO symbol
7. MAINTENANCE symbol
8. START symbol
9. Display dialog system
10. Water tank with handle
11. Filler funnel for pre-ground coffee
12. Bean tank cover
13. Aroma preservation cover
14. Steam / hot water draw-off tap
15. Profi-Auto-Cappuccino Frother with milk pipe
16. Interchangeable hot water nozzle (see Fig. 5)
17. Height-adjustable coffee spout
18. Coffee grounds container
19. Drip grate
20. Drip tray
21. MILD symbol
22. NORMAL symbol
23. STRONG symbol
24. Power switch
10
9
13
14
17
18
11
1
2
12
20
15/16
19
24
397
456 8212223

6
Contents
1. Safety information ..............................................page 7
1.1 Warning.....................................................page 7
1.2 Precautions.................................................page 7
2. Preparing the IMPRESSA .......................................page 7
2.1 Check supply voltage.....................................page 7
2.2 Check electrical fuse ......................................page 7
2.3 Fill water tank..............................................page 8
2.4 Fill coffee beans ...........................................page 8
2.5 Adjusting the grinding gear .............................page 8
2.6 Power switch...............................................page 8
3. First use ...........................................................page 8
4. Adjusting the water hardness .................................page 9
5. Installation of CLARIS plus filter cartridges..................page 10
5.1 Installing the filter.........................................page 10
5.2 Replacing the filter........................................page 11
5.3 Changing the filter without display request ..........page 11
6. Rinsing the IMPRESSA ..........................................page 11
6.1 Rinsing the IMPRESSA without display request......page 12
7. Adjusting the water quantity for coffee .....................page 12
8. Making 1 cup of coffee .........................................page 12
9. Making 2 cups of coffee........................................page 13
10. Drawing off pre-ground coffee................................page 13
11. Drawing off hot water ..........................................page 14
12. Dispensing steam ...............................................page 14
13. Dispensing Cappuccino with the Professional
Cappuccino Frother .............................................page 15
13.1 Dispensing Hot Milk with the
Professional Cappuccino Frother .......................page 16
13.2 Cleaning of the Professional Cappuccino Frother ...page 16
13.3 Rinsing the Professional Cappuccino Frother ........page 16
13.4 Cleaning the Professional Cappuccino Frother ......page 17
14. Switching off the IMPRESSA ...................................page 17
15. Programming ....................................................page 18
15.1 Programming the filter...................................page 18
15.2 Programming the water hardness......................page 18
15.3 Maintenance menu .......................................page 18
15.4 Programming the aroma INTENSIVE
or STANDARD..............................................page 18
15.5 Programming the temperature.........................page 19
15.6 Programming the time...................................page 19
15.7 Programming the automatic switch-on time ........page 20
15.8 Programming the automatic switch-off time ........page 20
15.9 Cup counter ................................................page 21
15.10 Programming the language .............................page 21
15.11 Programming Display 24H/AM/PM.....................page 22
15.12 Programming the display for ML/OZ ..................page 22
15.13 Exit programming mode.................................page 22
16. Maintenance......................................................page 23
16.1 Filling in water .............................................page 23
16.2 Emptying the coffee grounds container ..............page 23
16.3 Drip tray missing ..........................................page 23
16.4 Fill coffee beans ...........................................page 23
16.5 Replacing the filter........................................page 23
16.6 Cleaning the IMPRESSA ..................................page 24
16.7 IMPRESSA calcified ........................................page 24
16.8 General cleaning instructions ...........................page 24
16.9 Emptying the system.....................................page 24
17. Cleaning...........................................................page 25
17.1 Cleaning without display request ......................page 25
18. Descaling..........................................................page 26
18.1 Decalcifying without display request ..................page 27
19. Disposal ...........................................................page 27
20. Tips for perfect coffee ..........................................page 28
21. Messages..........................................................page 29
22. Problems..........................................................page 30
23. Legal information................................................page 31
24. Technical data....................................................page 31

7
Introduction
Thank you for purchasing the IMPRESSA. To ensure perfect function-
ing of your IMPRESSA, carefully read this operating manual and keep
it for future reference.
Should you need more information or if you encounter particular
problems not specified in these operating instructions in sufficient
detail, either contact us directly or contact your local authorized
dealer.
You will also find useful tips on operation and maintenance of
your IMPRESSA on our website at www.jura.com.
1. Safety information
1.1 Warning
䡲Children do not realize the dangers involved in using electric
appliances, for this reason always keep an eye on children when
they use electric appliances.
䡲The coffee machine may only be used by instructed persons.
䡲Never use a defective coffee machine or a machine with a defective
mains cable.
䡲Never repair or open the coffee machine yourself. Any repairs may
only be carried out by authorized service shops using original spare
parts and accessories.
䡲Never immerse the coffee machine in water.
1.2 Precautions
䡲Never expose the coffee machine to weather (rain, snow, frost),
never touch the machine when your hands are wet.
䡲Place the IMPRESSA on a firm, level base that is resistant to any
water that may leak. Never stand on hot or warm surfaces (oven
hobs). Keep out of the reach of children.
䡲If you don’t use the machine for a longer time (holidays, etc.)
always disconnect the mains cable.
䡲Always disconnect mains cable before cleaning the machine.
䡲When disconnecting the mains cable never pull on the mains cable
or the machine itself.
䡲The coffee machine is connected to mains supply via a mains cable.
Make sure nobody can trip over the mains cable. Make sure
children and pets cannot reach the machine
䡲Never put the coffee machine or individual parts of it into a dish-
washer.
䡲Make sure to install the machine at a place with sufficient air circu-
lation, to prevent overheating of the machine.
2. Preparing the IMPRESSA
2.1 Check supply voltage
The IMPRESSA is preset in the factory to the correct mains voltage.
Check if your local mains supply voltage complies with the infor-
mation given on the type plate on the underside of the IMPRESSA.
2.2 Check electrical fuse
The IMPRESSA is designed for an electric current of 10 amperes. Check
if the electrical fuse has sufficient capacity.
E

8
2.3 Fill water tank
Only use fresh, cold water. Never fill in milk, mineral water or
other liquids.
䡲Remove the water tank and rinse it with cold tap water thoroughly
(Fig. 4).
䡲Then fill the water tank and reinstall it. Make sure to install the tank
properly, it must engage audibly.
2.4 Fill coffee beans
To ensure that your machine will work perfectly for a long time
and to avoid damage, please note that the grinding gear of
your JURA coffee machine is not suitable for coffee beans which
were treated, during or after roasting, with additives (e.g.
sugar). Such coffee blends may damage the grinding gear. Any
repair costs resulting from the use of such blends are not
covered by warranty.
䡲Open the bean tank cover (12) and remove the aroma preservation
cover (13).
䡲Remove any dirt or foreign matter from the bean tank.
䡲Fill coffee beans in the bean tank and close the cover.
2.5 Adjusting the grinding gear
You can adjust the grinding gear to the roast of your coffee. We rec-
ommend
a fine grinding degree 씮for bright roasts (the smaller the dots,
the finer the grinding)
a coarse degree 씮for dark roasts (the larger the dots, the
coarser the grinding)
The grinding degree may only be adjusted while the grinding
gear is running.
䡲Open the bean tank cover (12) and remove the aroma preservation
cover (13).
䡲To adjust the grinding degree, turn the Rotary Switch (Fig. 2) to the
required position.
2.6 Power switch
Actuate the power switch (24) on your IMPRESSA before using
the machine for the first time.
We recommend that you switch off your IMPRESSA with the
power switch (24) if you intend not to use the machine for
longer periods of time (e.g.during holidays).
3. First use
䡲Fill coffee beans in the bean tank (12).
䡲Switch on the IMPRESSA using the power switch (24).
䡲
Your IMPRESSA is in standby mode.
䡲Touch the (3) symbol
䡲SPRACHE
DEUTSCH
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until the required language is displayed
(Fig. 17).
䡲For example LANGUAGE
ENGLISH

9
E
䡲Confirm your selection by pressing the Rotary Switch (1) (Fig. 17).
䡲FILL
WATER
䡲Fill the water tank (10) with fresh water.
䡲OPEN TAP
䡲Place a receptacle under the Professional Cappuccino Frother (15)
(Fig. 10).
䡲Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲FILLING
SYSTEM
䡲CLOSE TAP
䡲Close the steam / hot water draw-off tap (14).
䡲FILLING SYSTEM
䡲HEATING
䡲PRESS
MAINT.
䡲Touch the symbol (7).
䡲Machine carries out a rinsing operation.
䡲RINSING
䡲READY
If BEANS FILL is displayed, press the coffee draw-off key again.
Machine not filled with coffee beans yet.
To get an excellent crema, adjust the coffee spout (17) to the
size of your cup (Fig. 3).
4. Adjusting the water hardness
Water is heated in the IMPRESSA. As a result, calcification oc-
curs during normal use and is indicated automatically. Before
using the IMPRESSA for the first time the hardness of the water
used must be adjusted. Use the supplied test sticks for this.
1° German hardness is equivalent to 1.79° French hardness.
If the filter is activated, the program step Water Hardness no
longer appears.
The IMPRESSA has 5 hardness degrees which can be used and
are displayed while you are adjusting the water hardness.
The displayed information means the following:
LEVEL –– Water hardness function switched off
LEVEL 1 German water hardness degree 1 to 7°
French Water hardness degree 1.79 – 12.53°
LEVEL 2 German water hardness degree 8 to 15°
French Water hardness degree 14.32 – 26.85°
LEVEL 3 German water hardness degree 16 to 23°
French Water hardness degree 28.64 – 41.14°
LEVEL 4 German water hardness degree 24 to 30°
French Water hardness degree 42.96 – 53.7°
When the IMPRESSA leaves the factory it is adjusted to LEVEL 3. You
can adjust another hardness. To do this, proceed as follows:
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears

10
䡲FILTER –
䡲Turn the Rotary Switch (1) until the following message is displayed:
䡲HARDNESS
䡲Now press the Rotary Switch (1) to start the programming.
䡲LEVEL 3
䡲Turn the Rotary Switch (1) until the required level is displayed.
䡲For example, LEVEL 4
䡲Press the Rotary Switch (1) to confirm the required level.
䡲HARDNESS
䡲Turn the Rotary Switch (1) until
EXIT appears
䡲Press the Rotary Switch (1) to leave the programming mode.
䡲READY
5. Installation of CLARIS plus filter cartridges
If the CLARIS plus filter cartridge is installed properly, descaling
of the coffee machine is no longer required. For more infor-
mation on the CLARIS plus filter cartridge refer to brochure
‘CLARIS plus. Hard on limescale. Gentle on your coffee
machine.’
5.1 Installing the filter
Draw off 1/2 litre of water to rinse filter completely. In order to
ensure perfect operation, close tap (14) only after the display
says
CLOSE TAP
䡲Fold up the cartridge holder. Install the filter cartridge in the water
tank, applying a gentle pressure (Fig. 1).
䡲Fold down the cartridge holder again until it engages audibly.
䡲Fill the water tank with cold, fresh tap water and install it again.
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲FILTER –
䡲Press the Rotary Switch (1) to start the programming.
䡲NO –
䡲Turn the Rotary Switch (1) until the following message is displayed:
䡲YES ⻫
䡲Press the Rotary Switch (1) to activate the filter cartridge.
䡲INSERT
OPEN TAP
䡲Put a sufficiently large container (at least 0.5 litre) under the Pro-
fessional Cappuccino Frother (15) (Fig. 10).
䡲Turn the selector switch of the Professional Cappuccino Frother (15)
to the steam position (Fig. 20).
䡲If not installed already, insert the CLARIS plus filter.
䡲Open the steam / hot water draw-off tap (14) (Fig.12).
䡲RINSING
FILTER
䡲CLOSE TAP
䡲Close the steam/hot water draw-off tap (14), now the IMPRESSA will
heat up to coffee temperature.

11
E
䡲HEATING UP
䡲READY
Now you have activated the filter. In Programming Mode the
water hardness selection function is no longer displayed.
5.2 Replacing the filter
Draw off 1/2 litre of water to rinse filter completely. In order to
ensure perfect operation, close tap (14) only after the display
says
CLOSE TAP
After drawing off approx. 50 litres, the filter cartridge will be
used up. A message requesting you to replace the filter will
appear on the display. The scale on the cartridge holder in the
water tank will tell you how much longer you can use the
CLARIS plus filters.
䡲CHANGE FILTER / MACHINE READY
䡲Touch the symbol (7).
䡲REPLACE
OPEN TAP
䡲Remove the water tank from the machine and empty it.
䡲Fold up the cartridge holder. Install the filter cartridge in the water
tank, applying a gentle pressure (Fig. 1).
䡲Fold down the cartridge holder again until it engages audibly.
䡲Fill the water tank with cold, fresh tap water and reinstall it.
䡲Place a sufficiently large receptacle (at least 1/2 litre) under the
Professional Cappuccino Frother (15) (Fig. 10).
䡲Turn the selector switch of the Professional Cappuccino Frother (15)
to the steam position (Fig. 20).
䡲Open the tap for dispensing steam/hot water (14) (Fig. 12).
䡲RINSING
FILTER
䡲CLOSE TAP
䡲Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲HEATING UP
䡲READY
5.3 Changing the filter without display request
䡲Press the Rotary Switch (1) until
FILTER ⻫appears.
䡲Press the Rotary Switch (1) to confirm.
䡲YES ⻫
䡲Press the Rotary Switch (1) again to confirm.
䡲INSERT/OPEN TAP
䡲The program ‘Change filter’ is now active. Now proceed as
described in Chapter 5.2 from REPLACE/OPEN TAP
onwards.
6. Rinsing the IMPRESSA
When the IMPRESSA is switched off and has cooled down, a
rinsing operation is started when the machine is switched on
again. When the machine is switched off, a rinsing operation is
started automatically.

12
You can adjust the water quantity in steps of 5 ML using the Rotary
Switch (1).
䡲READY
䡲Turn the Rotary Switch (1) until the required water quantity is
displayed.
䡲For example, 120 ML
8. Making 1 cup of coffee
You can choose from 3 different coffee strengths. Touch one of
the symbols / / to select the strength of your coffee.
MILD NORMAL STRONG.
You can set the amount of water you want with the Rotary
Switch (1) prior to drawing off coffee
Touch the (8) symbol to stop drawing off coffee pre-
maturely.
The amount of coffee water you used last is saved by the
IMPRESSA until the next time you make coffee.
Press the Rotary Switch (1) briefly to check how much coffee
water you used last.
䡲READY
䡲Place a cup under the height-adjustable coffee spout (17).
䡲Touch the (5).
䡲COFFEE symbol
䡲Select an aroma by touching one of the symbols
䡲E.g. (STRONG aroma)
䡲Touch the symbol (3).
䡲HEATING UP
䡲PRESS
MAINT.
䡲Touch the symbol (7).
䡲RINSING
䡲READY
6.1 Rinsing the IMPRESSA without display request
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears.
䡲Turn the Rotary Switch (1) until
MAINTENANCE appears.
䡲Press the Rotary Switch (1) to confirm.
䡲RINSE
䡲Press the Rotary Switch (1) again to confirm.
䡲RINSING
䡲READY
7. Adjusting the water quantity for coffee
The indicated value in ML is a reference value and may deviate
from the actual value
You can change/stop the water quantity during the draw-off
operation, too. Turn the Rotary Switch (1) until the required ML
value is displayed.

13
E
䡲STRONG
䡲Touch the (8) symbol
䡲160 ML (water quantity last adjusted).
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until the required amount of coffee water
appears on the display (9).
䡲e.g. 120 ML
䡲COFFEE
䡲Your coffee is being prepared.
䡲READY
9. Making 2 cups of coffee
You cannot choose the strength of the coffee when making
2 cups. The machine automatically makes 2 mild cups of coffee.
You can set the amount of water you want with the Rotary
Switch (1) prior to drawing off coffee
Touch the (8) symbol to stop drawing off coffee pre-
maturely.
The amount of coffee water you used last is saved by the
IMPRESSA until the next time you make coffee.
Press the Rotary Switch (1) briefly to check how much coffee
water you used last.
䡲READY
䡲Place two cups under the height-adjustable coffee spout (17).
䡲Touch the coffee draw-off symbol of your choice twice
䡲2 COFFEE
䡲120 ML (water quantity last adjusted).
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until the required amount of coffee water
appears on the display (9).
䡲e.g. 210 ML
䡲2 COFFEE
䡲Your coffee is being prepared.
䡲READY
10. Drawing off pre-ground coffee
Never use instant coffee or quick-coffee. We recommend that
you always use powder from fresh coffee beans or, pre-ground,
vacuum-packed coffee. Never fill in more than 2 portions of
powder. The pre-ground coffee tank is no storage tank. Make
sure that the pre-ground you use is not too fine. This may
cause blocking of the system. In this case the coffee only drips
out of the coffee spout.
If you have filled in too little powder, the message NOT
ENOUGH POWDER will be displayed. The IMPRESSA stops the
operation and returns to ‘ready for draw off’ mode.
You can stop the draw-off operation at any time by pressing
any coffee draw-off key.
䡲READY
䡲Put 1 or 2 cups under the adjustable coffee spout (17).

14
䡲Open the cover of the filler funnel for pre-ground coffee (11).
䡲FILL
POWDER
䡲Fill 1 or 2 level spoonfuls of pre-ground coffee in the filler funnel for
pre-ground coffee (11) (Fig. 15) and close the cover.
䡲SELECT
KEY
䡲Press the required draw-off key.
䡲Touch the (8) symbol
䡲120 ML (water quantity last adjusted)
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) again to select the water quantity indi-
vidually:
䡲For Example: 210 ML
䡲COFFEE
䡲Your product is being prepared.
䡲READY
11. Drawing off hot water
The amount of hot water you used last is saved by the
IMPRESSA until the next time you make coffee.
Install the hot water nozzle (see Fig. 5) to obtain perfect water
flow. Do not replace the replaceable hot water nozzle (16)
directly after drawing off water, because the nozzle is hot after
the draw-off operation.
At the start of the water draw-off operation there can be
splashing Avoid direct contact with the skin!
䡲READY
䡲Place a cup under the replaceable hot water nozzle (16).
䡲Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲The illuminated ring (2) is active.
䡲STEAM
䡲Touch the (8) symbol
䡲For example, 140 ML
䡲WATER
䡲Adjust the required water quantity by turning the Rotary Switch (1).
䡲For example, 200 ML
䡲WATER
䡲If the required water quantity is reached, the following message is
displayed:
䡲CLOSE TAP
䡲Close the steam / hot water draw-off tap (14).
䡲READY
Before CLOSE TAP water may still escape the system.
12. Dispensing steam
The steam function is used for the preparation of milk foam
and hot milk, as well as for the Professional Cappuccino Frother
(15) cleaning programme.
With the optionally available 2-stage frothing nozzle, liquids
can be heated and frothed using the steam function.

15
E
Make sure that the nozzle is correctly fitted when drawing
steam. If the nozzle becomes blocked with particles of milk
residue or is incorrectly assembled, a danger can arise during
use whereby the nozzle may jump off.
Due to the system design, some water will escape at first when
steam is drawn. However, this will not affect the result in any
way.
When drawing steam, spluttering can occur at the start. The
nozzle becomes hot in use. Avoid any direct skin contact.
䡲READY
䡲To draw off steam, open the steam/hot water draw-off tap (14)
(Fig. 12).
䡲The illuminated ring (2) is active.
䡲STEAM
䡲You can adjust the steam draw-off time individually by turning the
Rotary Switch (1) until the required SEC are displayed.
䡲For example, 35 SEC
䡲If you do not change the steam draw-off time settings using the
Rotary Switch (1), the machine will use the settings last adjusted.
䡲During the steam draw-off operation, the message STEAM is dis-
played.
䡲When the steam quantity is reached, the message CLOSE TAP is
displayed.
䡲Close the steam / hot water draw-off tap (14).
䡲READY
At any time, you can abort steam dispensing early, by closing
the tap for dispensing steam/hot water (14).
Before CLOSE TAP, steam may still escape the system.
13. Dispensing Cappuccino with the
Professional Cappuccino Frother
Cappuccino comprises one third each of Espresso, hot milk
and milk foam. You produce the milk portion with the Profes-
sional Cappuccino Frother (15).
When steam is drawn, a vacuum is produced which, with the
aid of the Professional Cappuccino Frother (15), draws in the
milk and produces milk foam.
To ensure perfect function, the Professional Cappuccino Frother
(15) must be cleaned regularly.
Make sure that the nozzle is correctly fitted. If the nozzle
becomes blocked with particles of milk residue or is incorrectly
assembled, a danger can arise during use whereby the nozzle
may jump off.
䡲When using for the first time, remove the protective cover from the
Professional Cappuccino Frother (15) (Fig. 6). The protective cover is
used only during transport as protection to prevent the ingress of
contaminated materials.
䡲Remove the milk pipe from the Welcome Pack and connect it to
the Professional Cappuccino Frother (15).
䡲Insert the other end of the milk pipe into a Tetra Pak of milk or
connect it to a milk container (Fig. 7).
䡲Place a cup under the Professional Cappuccino Frother (15) (Fig. 7).

16
A useful addition is available for all lovers of milk specialities in
the form of high-quality vacuum milk containers. They keep
the milk cool the whole day long and are optimally suited to
the design of your IMPRESSA.
All original JURA accessories can be obtained from the specialist
shop.
䡲Turn the selector switch of the Professional Cappuccino Frother (15)
to the milk foam position (Fig. 19).
䡲READY
䡲Open the steam / hot water draw-off tap (14) (Fig. 12). The milk
foam is prepared.
䡲The illuminated ring (2) is active.
䡲STEAM
䡲You can adjust the steam draw-off time individually by turning the
Rotary Switch (1) until the required SEC are displayed.
䡲For example, 35 SEC
䡲If you do not change the steam draw-off time settings using the
Rotary Switch (1), the machine will use the settings last adjusted.
Adjust the steam dispensing time to suit the size of your cup.
䡲During the steam draw-off operation, the message STEAM is dis-
played.
䡲When the steam quantity is reached, the message CLOSE TAP is
displayed.
䡲Close the steam / hot water draw-off tap (14).
䡲READY
Due to the system design, steam can still escape and some
milk may continue to drip before the TAP is closed.
At any time, you can abort steam dispensing early, by closing
the tap for dispensing steam/hot water (14).
䡲Now, move your cup with the milk foam and place it under the cof-
fee spout and dispense the required coffee product. (Fig. 8).
Your Cappuccino is ready.
13.1 Dispensing Hot Milk with the
Professional Cappuccino Frother
Turn the selector switch of the Professional Cappuccino Frother
(15) to the milk range (Fig. 21).
The procedure for dispensing hot milk is the same as the pro-
cedure for dispensing milk foam for Cappuccino (Chapter 13).
13.2 Cleaning of the
Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother functions
perfectly, you should rinse it with water each time after pre-
paring milk.
You will not be prompted by your IMPRESSA to rinse the Pro-
fessional Cappuccino Frother.
13.3 Rinsing the Professional Cappuccino Frother
䡲Carefully pull off the Professional Cappuccino Frother from your
IMPRESSA.
䡲Dismantle the Professional Cappuccino Frother (15) into its indi-
vidual parts (Fig. 16).

17
E
䡲Thoroughly rinse all parts of the nozzle under running water.
䡲Reassemble the Professional Cappuccino Frother (15) and refit it on
to your IMPRESSA.
13.4 Cleaning the Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother (15) func-
tions perfectly, you should clean it daily if you have prepared
milk foam or hot milk.
You will not be prompted by your IMPRESSA to clean the Pro-
fessional Cappuccino Frother (15).
You can obtain the JURA Auto-Cappuccino Cleaner from the
specialist shop.
䡲Place a receptacle under the Professional Cappuccino Frother (15)
(Fig. 9).
䡲Fill a second receptacle with 2.5 dl of fresh water and add one cap-
ful of the Auto-Cappuccino Cleaner.
䡲Dip the milk pipe into the second receptacle with the Auto-
Cappuccino Cleaner (Fig. 9).
䡲Turn the selector switch of the Professional Cappuccino Frother (15)
to the milk position (Fig. 21) or to the milk foam position (Fig. 19).
䡲READY
䡲Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲Draw steam until the receptacle with the Auto-Cappuccino Cleaner
is empty.
This procedure cleans the Professional Cappuccino Frother and the
milk pipe.
䡲Close the steam / hot water draw-off tap (14).
䡲READY
Before CLOSE TAP water may still escape the system.
䡲Fill the receptacle with 2.5 dl of fresh water.
Dip the milk pipe into the receptacle with the fresh water.
䡲Open the tap for dispensing steam/hot water (14) (Fig. 12) in order
to draw steam.
䡲Draw steam until the receptacle with the fresh water is empty.
This procedure rinses the Professional Cappuccino Frother (15) and
the milk pipe with fresh water.
䡲Cleaning of the Professional Cappuccino Frother (15) is now com-
plete, your IMPRESSA is ready for use.
14. Switching off the IMPRESSA
In order to ensure perfect operation, please don’t switch off
your IMPRESSA at the power switch (24) before all the symbols
on the display (9) have gone off except for (3).
䡲READY
䡲Switch off the IMPRESSA using the ON/OFF key (3).
䡲RINSING
䡲An automatic rinsing operation is started.
䡲
Your IMPRESSA is in standby mode.

18
15. Programming
When your IMPRESSA leaves the factory it is adjusted such that
you can draw off coffee without having to change any settings.
However, you can programme various parameters individually.
You can programme the following stages:
쐌Filter
쐌Water hardness
쐌Maintenance
쐌Aroma
쐌Temperature
쐌Time
쐌Automatic switch-on time
쐌Automatic switch-off time
쐌Draw-offs
쐌Language
쐌Display
쐌Exit
To start programming, press the Rotary Switch (1) until
FILTER –/⻫appears
Rotary switch
Turn the Rotary Switch to change the adjusted values or to
select the next programming step.
Press the Rotary Switch to check the values adjusted or to save
the values selected (Fig. 17).
15.1 Programming the filter
Refer to Chapter 5.1 ‘Inserting the filter’.
15.2 Programming the water hardness
Refer to Chapter 4 ‘Adjusting the water hardness’.
15.3 Maintenance menu
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until
MAINTENANCE appears
䡲Press the Rotary Switch (1)
䡲RINSE
䡲Turn the Rotary Switch (1) until the required program item appears
on the display (9).
䡲e.g. RINSE, CLEAN, FILTER, DE-SCALE or EXIT
䡲e.g. CLEAN
䡲Press the Rotary Switch (1)
䡲The cleaning program starts.
䡲EMPTY TRAY
䡲Continue with Chapter 17 Cleaning, from point 3
EMPTY TRAY
15.4 Programming the aroma INTENSIVE
or STANDARD
When the machine leaves the factory, the aroma is set to
intensive. If requested it can also be set to Standard.

19
E
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until Aroma is displayed.
䡲AROMA
䡲Press the Rotary Switch (1).
䡲INTENSIVE
䡲Turn the Rotary Switch (1) until the following message is displayed:
䡲STANDARD
䡲Press the Rotary Switch (1) to save the setting.
䡲AROMA
䡲Turn the Rotary Switch (1) until
EXIT appears
䡲Press the Rotary Switch (1) to leave the programming mode.
䡲READY
15.5 Programming the temperature
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until Temperature is displayed.
䡲TEMPERATURE
䡲Press the Rotary Switch (1).
䡲HIGH
䡲Turn the Rotary Switch (1) to change the temperature from HIGH to
NORMAL (or vice versa).
䡲NORMAL
䡲Press the Rotary Switch (1) to save the setting.
䡲TEMPERATURE
䡲Turn the Rotary Switch (1) until
EXIT appears
䡲Press the Rotary Switch (1) to leave the programming mode.
䡲READY
15.6 Programming the time
You must programme the time if you want to use the auto-
matic switch-on function.
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until TIME is displayed.
䡲TIME
䡲Now press the Rotary Switch (1) to start programming the time.
䡲--:--
䡲Turn the rotary Switch (1) to adjust the hours..
䡲12:--
䡲Press the Rotary Switch (1) to confirm the hour settings and to
activate the minutes.
䡲12:--

20
䡲Turn the Rotary Switch (1) to select the minutes.
䡲2:05
䡲Press the Rotary Switch (1) to save the setting.
䡲TIME
䡲Turn the Rotary Switch (1) until
EXIT appears
䡲Press the Rotary Switch (1) to leave the programming mode.
䡲READY
If the machine is disconnected from power supply, the time
must be programmed again.
15.7 Programming the automatic switch-on time
You must programme the time (Chapter 15.6) if you want to
use the automatic switch-on function (––:–– = inactive).
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until MACHINE ON is displayed.
䡲MACHINE ON
䡲Now press the Rotary Switch (1) to start programming the switch-
on time.
䡲--:--
䡲Turn the Rotary Switch (1) to adjust the hours.
䡲12:--
䡲Press the Rotary Switch (1) to confirm the hour settings and to acti-
vate the minutes.
䡲12:--
䡲Turn theRotary Switch (1) to select the minutes.
䡲12:05
䡲Press the Rotary Switch (1) to save the setting.
䡲MACHINE ON
䡲Turn the Rotary Switch (1) until
EXIT appears
䡲Press the Rotary Switch (1) to leave the programming mode.
䡲READY
15.8 Programming the automatic switch-off time
You can programme your coffee machine such that it will
switch off automatically after a certain time. You can pro-
gramme the switch-off time in a range between 0.5 and
9 hours, or select ––:–– (i.e. inactive).
䡲READY
䡲Press the Rotary Switch (1) until
FILTER –/⻫appears
䡲The illuminated ring (2) is active.
䡲Turn the Rotary Switch (1) until OFF AFT. HR is displayed.
䡲OFF AFT. HR
䡲Now press the Rotary Switch (1) to start programming the switch-
off time. Switch-off time OFF AFT. HR
䡲5.0 HR