keilhauer Buncha User manual

keilhauer.com
1450 Birchmount Road
Toronto, Ontario,
Canada
M1P 2E3
T 416 759 5665
F 416 759 5723
1 800 724 5665
Buncha
Assembly Guide

Tool Required
Hex Allen Key
Hardware Included
Buncha Non - Powered Assembly Instructions
1/4-20 x 3/4”
Hex button head cap screw (x32)
Place the table top upside down on a blanket. Using the hex key, fasten the four legs with 1/4-20 x 3/4”
Hex button head cap screw (x32).
Proceed to flip the table top into its final position.
12
3
Phillips Driver
2

Buncha with Power Assembly Instructions
Tool Required
Hex Allen Key
Hardware Included
1/4-20 x 3/4”
Hex button head cap screw
(x32)
Cable management clips
(x2)
Cable management
Adhesive velcro loops
(x4)
Mini Tap clamp bar Mini Tap thumb screw (x2) Power Box
Place the table top upside down on a blanket. Power Leg (x1)
1) This leg includes a channel for the power cable.
Ensure this leg is fastened to the corner nearest
the power outlet source.
2) Using the hex key, fasten the four legs with
1/4 - 20 x 3/4” Hex button head cap screw (x32).
Place the table on its edge on a blanket. 1) Insert the power box and feed the power cable through
the table cut-out.
2) Slide the Mini Tap clamp bar into the slot, then fasten
with the Mini Tap thumb screw (x2) until tight.
12
34
Cable management
Adhesive velcro hooks
(x1)
Place the table upside down on a blanket. Remove the
channel leg cover off the power leg, and proceed to set
the power cable into the channel leg.
5
3

Place the channel leg cover over the channel leg. Firmly
press on the cover to ensure it is set in place and sits
flush with the leg.
Buncha with Power Assembly Instructions
(Continued)
56
Place self adhesive cable management clip (x1) at the
location above.
Unpackage the adhesive tabs with velcro (x2) that
accompany the control box, then proceed to place
them on the underside of control box.
Fasten control box to underside of table at the location
above. Feed cable through cable management clip.
Connect control box cord to daisy chain connection. Place the velcro loops (x4) at the locations above.
78
910
4

Place (x1) self adhesive cable management clip at the
location above.
Flip over and place the table in its final position.
16
In order to link the power connection between
multiple tables, only one table requires the power leg.
All additional tables ( maximum of x7) can be powered
by using the daisy chain extension piece above (Short
cord).
Power Linking Buncha Tables
11
15
EXTREME HAZARD WARNING:
IN ORDER TO PREVENT ELECTRICAL DAMAGE
AND/OR FIRE, A MAXIMUM OF (x8) TABLES CAN BE
POWER LINKED TOGETHER.
Buncha with Power Assembly Instructions
(Continued)
Feed the ganging plug cable through the cable
management clip (x1).
12
Place (x1) velcro hook on the underside of the ganging
plug.
If the table is not being daisy chained to another table,
the ganging plug can be fastened to the velcro loop at
the location above. If the table is being daisy chained to
another ganged table, instead fasten the ganging plug to
one of the (x3) velcro loops closest to the side which the
table is ganged.
13 14
5

Buncha Ganging Instructions
Table 1 Table 2
Tool Required Hardware Included
Phillips Driver 1/4 - 20 x 3/4” Phillips (x4) Ganging Mechanism (x2)
Top view
Side view
Underside view
Table 1 Table 2
B Male component
A Female component
A
A
B
B
Underside view
1
Locate the two pilot holes located at each end of the
underside of the table. With the Phillips driver, fasten the
ganging mechanism to each end of the table using (x2)
1/4 - 20 x 3/4” screw.
Ensure table edges are aligned and level with each other
prior to ganging.
2
3
Figure 1 Figure 2
Rotate the Male Component B on each table until it
clicks into Female component A (See Figure 1 & 2).
6

Modesty Panel Assembly Instructions
Place the table on its edge on a blanket.
Flip over and place the table in its final position.
1
4
1) Slide the modesty screen onto the table legs.
2) Insert the modesty panel clips onto the top edge of
the modesty panel, then proceed clip them into the
pilot holes on the underside of the table top.
3
Modesty Panel Clip (x7)
Hardware Included for Modesty Panel
When installing the modesty panel, ensure the folded
fabric seam circled above is facing inwards.
2
7