Kensington K67862EU Manual

Register Now!
Enregistrer maintenant !
Jetzt registrieren!
Nu registreren
Registrar ahora
Registra adesso
Regisztràljon most!
Zaregistrujte se nyní!
Zarejestruj się!
Зарегистрироваться!
Registe-se agora!
register.kensington.com
Charge and Sync Cabinet, Universal tablet
For 10 Tablets
INSTRUCTION GUIDE HASZNÁLATI ÚTMUTATÓ
GUIDE D’INSTRUCTIONS PŘÍRUČKA S POKYNY
BEDIENUNGSANLEITUNG INSTRUKCJA OBSŁUGI
HANDLEIDING РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
ISTRUZIONI MANUAL DE INSTRUÇÕES
MANUAL DE INSTRUCCIONES

English 3
Français 17
Deutsch 31
Nederlands 45
Italiano 59
Español 73
Magyar 87
Čeština 101
Polski 115
Русский 129
Português 143

2
IMPORTANT! REGISTER YOUR KEY CODE! /
IMPORTANT! ENREGISTREZ VOTRE CODE CLÉ! /
WICHTIG! REGISTRIEREN SIE IHREN KEYCODE! /
BELANGRIJK! REGISTREER UW SLEUTELCODE! /
IMPORTANTE! EFFETTUARE LA REGISTRAZIONE DEL
CODICE DELLA CHIAVE /
IMPORTANTE: REGISTRE EL CÓDIGO DE LA LLAVE /
FONTOS! REGISZTRÁLJA A KULCSKÓDJÁT! /
DŮLEŽITÉ! REGISTRUJTE KÓD SVÉHO KLÍČE! /
WAŻNE! ZAREJESTRUJ KOD KLUCZYKA! /
ВАЖНО! ЗАРЕГИСТРИРУЙТЕ СВОЙ КОД КЛЮЧА! /
IMPORTANTE! FAÇA O REGISTO DO SEU CÓDIGO CHAVE!
register.kensington.com

3
ACharge and Sync Cabinet
B USB Cable
CInstruction Guide
DWarranty Card
ESafety Information
FPower Cable
GScrews (2X)
HKeys (2X)
IBolts
JSlots for tablets
KLED Status Lights
L Sync Button and LED
MUSB Ports
NFan
OUSB Ports
PPower Switch
QPower Connector
Contents
Components
English
J
K
L M Q
N
O
1
2
3
4
5
6
7
8
9
10
P
AB
CDE
F
G
H
I

4
Install Cabinet
Securing
Option 1
1 Remove all shelves from the cabinet.
2 Mark holes for drilling onto surface (30mm maximum thickness). Insert four bolts
(M6 - not provided) from inside the cabinet and fasten with four hex nuts and washers
(not provided).
5.5 in (140.6 mm)
Front
Side
4.9 in (125.0 mm)

5
4
5
6
7
8
9
10
4x M6 bolts
4x M6x5 hex nuts
4x M6 washers
(Not provided)
Bolt lengths to be 30 mm + table
Thickness. When selecting bolt length,
round up.
Option 2
Desktop and Peripherals Locking Kit sold separately.
K64615

6
Option 3
Stacking
1 Remove the silicone pad from the cabinet.
2 Lower the second unit on top of the secured base unit. Fasten the top unit with four
screws (M6X40 - provided).
M6x40

7
Use a cable lock to lock the units together and tether them to an anchor.
NOTE:Up to two Charge and Sync Cabinets can be stacked together.
Locking
a
b

8
Set Up the Cabinet for Your Tablets
Power On
1Connect the power cable.
2Turn the power switch to On.
Load the Tablets
1Insert one tablet into each slot.
2
3
4
5
6
7
8
9
10

9
2Plug the USB end of the dock connector cable into the USB port on the
Charge and Sync Cabinet.
2
3
Cables sold separately:
K67864WW - Lightning, 10pk
K67865WW - 30 Pin, 10pk
K67866WW - Micro USB, 10pk
3Plug the other end of the cable into the dock connector on the tablet.
2
3
4
For larger cases, remove shelves and insert vertically

10
Charge the Tablets
Charging automatically begins when the dock connector is plugged into the iPad.
NOTE:The Charge and Sync Cabinet will not charge and sync the tablets at the same time.
LED Status
Green = Charged
Red = Charging in progress
Red and Green Flashing = Sync in process
Red Flashing = Over current protection
NOTE:Remove the Device and turn off the AC power for over current reset.
Configuring Your Charge & Sync Cabinet for iPads®
If you need to sync the classroom’s iPads using your laptop or desktop, simply visit Apple’s
Configuration page at http://help.apple.com/configurator/mac/1.0/?lang=en-
us#cadf1802aed to learn more. The site has all the information you need with easy to follow
directions.
Sync
iTunes Setup
1Launch the iTunes application on the host computer.
2Under Preferences, click on the Advanced tab. Uncheck Check for new software updates
automatically. This will prevent the automatic update process from interfering with the
syncing process.
3Click on the Device tab, make sure all options are unchecked.

11
4Prepare the iTunes library with apps and media that you intend to sync to the iPads.
iPad Setup
Configure each iPad before starting the syncing process. This can be done by connecting
the iPad directly to the host computer or by inserting it into the Charge and Sync Cabinet.
If connecting through the cabinet, only one iPad can be configured at a time.
1Connect the supplied USB cable to the host computer.
1
2Connect the other end of the USB cable to the USB port on the back of the Charge
and Sync Cabinet.
3Insert one iPad into the Charge and Sync Cabinet.
2
3
4
5
6
7
8
9
10

12
4In the iTunes sidebar, select the iPad under Devices.
5Click on the Summary tab, select Open iTunes when this iPad is connected and
Sync only checked songs and videos. Verify Manually managed music and videos
is not selected (this function would require you to drag and drop your selections
to each iPad).
6Click on each of the tabs at the top (Apps, Music, Movies, TV shows, Books, Photos)
and select which type of files you will want to sync on this iPad. Click the Sync or
Apply button.
7Repeat Steps 3 to 6 for each iPad that will be used in the Charge and Sync Cabinet.

13
Ready to Sync
1Insert one iPad into each slot.
1
2
3
4
5
6
7
8
9
10
NOTE:If the iPads are new, they should be fully charged before attempting to sync.
2Plug the USB connectors into the Charge and Sync Cabinet and the iPads. All the iPads
loaded in the Charge and Sync Cabinet will appear under Devices in iTunes.
2
3
4
5
6
7
8
9
10

14
3Press the Sync Button to start the sync process.
9
10
Sync disabled Sync enabled
4iTunes will launch and syncing will start automatically.
5When syncing is completed, an Eject icon will appear next to each device.
Click on the Eject icon or close iTunes to safely eject the iPad.
6Unplug the USB cable from the computer so charging can begin.
IMPORTANT!
Charging will not occur until the USB cable is unplugged from the host computer.
Multi-Cabinet Sync Connection
K33933 Mobile Hub
Sold separately

15
1Arrange the units in order on a secure surface.
2Place configured iPad devices in the slots, connect the dock connector cable to the iPads
and USB ports. Push Sync switch button to “ON”, LED light will appear in red.
3Connect all units together using a USB hub (K33933 Mobile Hub, sold separately).
iTunes will automatically detect the new searched device name.
NOTE:Adding a new iPad device to the station after the sync button has been activated will
require the sync button to be reset. Push the sync button off, and then on again to reset.
Syncing Android Tablets
To sync an Android device, please refer to the manufacturer’s instructions.
Technical Support
Technical support is available to all registered users of Kensington products. Technical
Support contact information can be found on the back page of this manual.
Web Support
You may find the answer to your problem in the Frequently Asked Questions (FAQ) section
of the Support area on the Kensington Website: www.support.kensington.com.
Telephone Support
There is no charge for technical support except long-distance charges where applicable.
Please visit www.kensington.com for telephone support hours. In Europe, technical
support is available by telephone Monday to Friday 09:00 to 18:00 (Central European time).
Please note the following when calling support:
• Call from a phone where you have access to your device.
• Be prepared to provide the following information:
– Name, address, and telephone number
– Name of the Kensington product
– Make and model of your computer
– System software and version
– Symptoms of the problem and what led to them

16
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses. and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
MODIFICATIONS: Modifications not expressly approved by Kensington may void the user’s authority to operate the
device under FCC regulations and must not be made.
SHIELDED CABLES: In order to meet FCC requirements, all connections to equipment using a Kensington input device
should be made using only the shielded cables.
FCC DECLARATION OF CONFORMITY COMPLIANCE STATEMENT
This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation. As defined in Section 2.909 of the FCC Rules, the responsible party for this device
is Kensington Computer Product Group, 333 Twin Dolphin Drive, Redwood Shores, CA 94065,USA.
INDUSTRY CANADA CONFORMITY
This device has been tested and found to comply with the limits specified in RSS-210. Operation is subject to the
following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES-003.
CE DECLARATION OF CONFORMITY
Kensington declares that this product is in compliance with the essential requirements and other relevant provisions of
applicable EC directives. For Europe, a copy of the Declaration of Conformity for this product may be obtained by
clicking on the Compliance Documentation link at www.support.kensington.com.
INFORMATION FOR EU MEMBER-STATES ONLY
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. For more
detailed information about recycling of this product, please contact your local city office, your household waste
disposal service, or the shop where you purchased the product.
Kensington and the ACCO name and design are registered trademarks of ACCO Brands. The Kensington Promise is a service
mark of ACCO Brands. iPad is a registered trademark of Apple Inc., registered in the U.S. and other countries.
All other registered and unregistered trademarks are the property of their respective owners.
© 2014 Kensington Computer Products Group, a division of ACCO Brands USA LLC. Any unauthorized copying, duplicating,
or other reproduction of the contents hereof is prohibited without written consent from Kensington Computer Products
Group. All rights reserved. 03/14

17
Français
AArmoire de chargement et de
synchronisation
B Câble USB
CMode d’emploi
DCarte de garantie
EConsignes de sécurité
FCâble d’alimentation
GVisserie (2X)
HClés (2X)
IBoulons
JEmplacements pour tablettes
KVoyants LED d’état
L Boutons de synchronisation et LED
MPorts USB
NVentilateur
OPorts USB
PInterrupteur
QConnecteur d’alimentation
Contenu
Composants J
K
L M Q
N
O
1
2
3
4
5
6
7
8
9
10
P
AB
CDE
F
G
H
I

18
Installation du coffret
Sécurisation
Option1
1 Enlevez toutes les étagères du coffre.
2 Marquez les trous de forage sur la surface (30 mm maximum d’épaisseur). Insérez
quatre boulons (M6 - non fournis) depuis l’intérieur du coffret et fixez-les à l’aide de
quatre écrous hexagonaux et rondelles (non fournis).
5,5 in (140,6 mm)
Avant
Côté
4,9 in (125,0 mm)

19
4
5
6
7
8
9
10
4 boulons M6
4 écrous hexagonaux M6x
4 rondelles M6
(Non fournis)
Les boulons doivent présenter une
longueur de 30 mm + l’épaisseur de la
table Choisissez des boulons d’une
longueur légèrement supérieure.
Option2
Kit de verrouillage pour bureau et périphériques vendu séparément.
K64615