KI WorkUp FX User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
WorkUp®Fixed-Height Table
Model FX
January 2019
Tools Required
• #3 Phillips Screwdriver
• 5mm Hex Key
Note: Before discarding any
packaging, confirm all components
received against the packing list.
Table assembly should be done on a
soft, protective surface.
Note: When tightening the M8
screws, first twist all four screws
in “finger tight”. Then tighten the
screws one quarter turn at time
using a diagonal tightening pattern
as shown in Detail A. Repeat the
diagonal pattern until all four screws
are tight (Figure 1 & Detail A).
Feet-to-Columns Assembly
1. Set the column on end with the hole
pattern facing up (Figure 1).
2. Place the foot over the column
end so the column fits into the
square hole in the foot. The slotted
holes in the foot should line up with
the four holes in the column end. If
not the foot needs to be removed and
repositioned at 90 degrees
(Figure 1).
3. Attach the foot using four
M8 x 20mm screws and four 8mm
flat washers, tightening each screw
one quarter turn at a time in a
diagonal pattern until all four screws
are tight (Figure 1 & Detail A).
4. Thread leveling glides into the holes
at the ends of the foot (Figure 1).
Note: If the roller foot option was
purchased, one foot will have
pre-assembled rollers.
5. Repeat steps 1 through 4 for the
second foot and column (Figure 1).
Figure 1
column
foot
leveling
glide
M8 x 20mm
screws
flat
washer
Detail
A

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkUp®Fixed-Height Table - Model FX
Assembly Instructions
Base-to-Tabletop Assembly
Note: The tabletop is pre-drilled for
installation of all components.
1. To avoid scratching the tabletop
place it with the top side down on a
soft, protective surface (Figure 2).
2. As illustrated, place the assembled
base over the pre-drilled holes on
the tabletop. Align the holes in the
tabletop with those in the spider plate
and attach to the tabletop using
#12 x 1” tapping screws in each
available hole (Figure 2).
3. Carefully invert the table to its
upright position. Caution: The table
is very heavy. Two or more people
are required to turn the table upright.
4. Adjust the leveling glides to level the
table.
Product Information
Maximum Load: The allowable load
is based on the size of the worksurface
and shall be evenly distributed on the
worksurface.
Allowable Load = Perimeter x 1.5 lbs.
Example: The allowable load for a
30” x 66” worksurface is
192 x 1.5 lbs. = 288 lbs.
Figure
2
tabletop
column
#12 x 1”
screw
spider plate

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkUp®Fixed-Height Table - Model FX
Assembly Instructions
Wire Trough (optional)
Note: The wire trough is an optional
accessory that must be ordered
separately.
1. An optional wire trough may mount
to the underside of the tabletop,
centered only on tables 48”-72”
wide, as illustrated in Detail B. If the
tabletop depth is 36”, the wire trough
can only mount behind the spider
plates as illustrated in Detail C.
2. Align the wire trough mounting
holes to the appropriate holes in the
tabletop. Using six #10 x 5/8”
pan head screws, secure the wire
trough to the tabletop as illustrated
(Figure 3, Details B or C).
Figure 3
tabletop
wire
trough
#10 x /”
pan head
screw
5
8
wire
trough
Detail B - Centered Wire T
rough
48”-72” Wide Tables
tabletop
wire
trough
tabletop
Detail C - Behind Cross-Tube Assembly
36” Tabletop Depth

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2019 Krueger International, Inc. All Rights Reserved • Code KI-62447R4/KI/PDF/0119
WorkUp®Fixed-Height Table - Model FX
Assembly Instructions