KI USPF2324 User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
Universal Height-Adjustable Screens
October 2017
Note: If tables do not have
pre-drilled holes under the tabletops
for installing screens, retrofitting will
be required. See page 4, “Retrofit
Drilling Guidelines.”
1. Carefully remove contents from
shipping cartons and identify parts
and hardware supplied.
Note: The Universal Height-
Adjustable Screen may be installed
on Pirouette, WorkUp, and Toggle
Table models. Certain table models
allow screens to be mounted on the
side of the table as a divider screen.
The assembly process is the same
for divider screens and privacy
screens. The following instructions
show the installation of a privacy
screen to a Pirouette Fixed-Base
Table, your configuration may vary.
Important: Two different adjustable
mechanisms are designed to install
for different screen widths/weights.
Each of the two mechanisms is
weight-balanced differently and is
color coded with a different green or
yellow round sticker applied under
the mounting bracket. It is important
to reference the Screen Model/
Mechanism Chart below and use the
correct mechanism per the screen
model being installed. If screens are
installed with the incorrect adjustable
mechanism(s), screens will not
be counter balanced properly and
disassembly and correct reassembly
will be required (Detail A).
2. Locate an adjustable mechanism
per the screen model being installed
and position the mounting bracket
to align with the pre-drilled holes on
the underside of the tabletop. Secure
mechanism to the underside of the
tabletop using four #12 x 1” screws
(Figure 1).
Figure 1
Pirouette table
fixed-base
#12 x 1”
PPH screws
adjustable
mechanism
mounting
bracket
vertical
railway
Screen
Model Mechanism 1Mechanism 2Mechanism 3
USPF2324 Yellow Yellow N/A
USPF2924 Yellow Yellow N/A
USPF3524 Yellow Green N/A
USPF4624 Green Green N/A
USPF5824 Green Yellow Green
USPF7024 Green Green Green
yellow or
green
sticker
Detail
AScreen Model/Mechanism Chart

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Universal Height-Adjustable Screens
Assembly Instructions
3. Insert a square holed sleeve onto
the adjustable mechanism rod, then
place the longer connecting rod
onto the square holed sleeve just
installed (Detail B). Finally, insert a
second square holed sleeve onto the
opposite end of the connecting rod
(Figure 2).
4. Locate another adjustable
mechanism and press the mounting
bracket up to the underside of the
worksurface, then slide it over and
insert the adjustable mechanism rod
into the square holed sleeve/long
connecting rod installed in step 4,
synchronizing the two mechanisms
together. Secure the mounting
bracket of the second mechanism to
the underside of the tabletop using
four #12 x 1” screws (Figure 3).
5. Screens installed to tables 60”
or greater have three adjustable
mechanisms per assembly. If
assembly contains a third
mechanism repeat steps 3 through 4.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Figure 3
adjustable
mechanism
mounting
bracket
square
holed sleeve
#12 x 1”
PPH screws
Detail
C
adjustable
mechanism
rod
square holed
sleeve
Figure 2
adjustable
mechanism
connecting
rod
square
holed sleeve
square
holed sleeve
connecting
rod
square
holed
sleeve
adjustable
mechanism
rod
Detail B
square
holed sleeve

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Universal Height-Adjustable Screens
Assembly Instructions
6. Once all adjustable mechanisms are
installed, position the screen onto
the backs of the vertical rails and
align mounting holes. Secure screen
to the rails using two knurled thumb
screws per mechanism (Figure 4).
Figure
4
adjustable
mechanism
vertical
railway
knurled thumb
screw
screen

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Universal Height-Adjustable Screens - Retrofit Drilling Guidelines
Assembly Instructions
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2017 Krueger International, Inc. All Rights Reserved • Code KI-AI-000017/KI/PDF/1017
1 /”
1
4
table C
6”
5 /”
3
8
Drilling Guidelines for Screen Model - USPF2324
6”
5 /”
3
8
table C
1
/”
1
4
107/”
16
9 /”
7
8
Drilling Guidelines for Screen Models - USPF2924 & USPF3524
107/”
16
9 /”
7
8
table C
1 /”
1
4
137/”
16
127/”
8
Drilling Guidelines for Screen Model - USPF4624
137/”
16
127/”
8
table C
1 /”
1
4
227/”
16
217/”
8
1/”
2
21/”
8
Drilling Guidelines for Screen Models - USPF5824 & USPF7024
227/”
16
217/”
8
Universal Height-Adjustable
Screen - Retrot Drilling
Guidelines
Note: If tables do not have
pre-drilled holes under the
tabletops for installing screens,
retrofitting will be required.
1. Take note of correct retrofit
drilling guideline illustrations for
mounting adjustable mechanisms
to tabletops. Depending on the
table unit ordered, the length
of the tabletop determines the
appropriate size of the Universal
Height-Adjustable Screen.
Reference the “Universal
Height-Adjustable Screen
Selection Chart” to determine
appropriate retrofit drilling
guidelines.
2. Position the adjustable
mechanism under the tabletop
surface at the designated
location. Using the mechanism
as a drilling template, mark the
mounting hole locations, making
sure the mechanism is parallel to
the edge of the tabletop. Then use
an 1/8” drill to bore pilot holes 1/2”
deep at each marked location.
Table
Length(s) Screen Model
N/A USPF2324
30” USPF2924
36” & 42” USPF3524
48” & 54” USPF4624
60” & 66” USPF5824
70” USPF7024
Universal Height-Adjustable
Screen Selection Chart