KI All Terrain ATSW45 User manual

Assembly Instructions
All Terrain®Mobile Furniture
Fixed-Height and Pin-Height Adjustable Tables with Eight-Screw Base Attachment
April, 2002
KI
1330 Bellevue Street
P.O. Box 8100
Green Bay, Wisconsin 54308-8100
www.ki.com
TEL [phone]
FAX [phone]
Assemble units as described herein only. To do otherwise may result in instability. All screws, nuts and bolts must be tightened and
checked periodically after assembly. Failure to assemble properly, or to secure parts may result in assembly failure and
injury. Illustrations and specifications are based on current product information at the time of this printing.
Tools Required:
#2 Phillips screwdriver
3/4" open end wrench
(for tables with casters)
Hardware Included:
(8) 1/4-20 x 3/4" Phillips pan-head screws
with nylon patch
4 total of one of the following:
locking casters (46.5147)
non-locking casters (46.5146)
glides (10.3000.BLWH)
1. To avoid scratching the tabletop, place
it face down on a soft protective
material. Refer to the top and base
packaging labels to identify the table
model number. Identify applicable
table illustration:
2. Unpackage appropriate table base
and refer to the illustration above for
proper base/leg orientation. Set the
base in place on the underside of the
worksurface aligning attachment
holes with threaded inserts in the
worksurface tops as shown.
Note: Front of tables are at the top
of illustration.
ATSW45/, ATSW57/,
ATSW63/, ATSW69
ATCC2754/, ATCC3054/ ATDU46/
ATRC3042/, ATRC3048/, ATRC3060 ATCC2448/, ATCC2748/
ATDU50/ ATSL2745/, ATSL3658/
ATEL2745/, ATEL3658/
ATRC2448/, ATRC2460/, ATRC2742/,
ATRC2748/, ATRC2760/
Note:
Postition longer
legs toward front
of table edge.
Note:
Postition longer
legs toward front
of table edge.

All Terrain®Mobile Furniture - Assembly Instructions
Fixed-Height and Pin-Height Adjustable Tables with Eight-Screw Base Attachment
3. Secure the bases on each side using
the screws provided (Figure 1).
4. Attach glides and/or casters to the
bases. See illustration and follow the
following guidelines below:
For 4CW - 4 casters
(2 locking & 2 non-locking):
Insert and tighten all four casters
using 3/4" open-end wrench.
The two locking casters are to be
toward the front edge of the table
(Figure 2).
For 4GB - 4 glides:
Insert glides. To achieve the
standard pin heights (and the
same height as with casters) turn
the glides in until 1/2" of the
telescoping sleeve is exposed
(Figure 2).
For 4MW - 2 glides and
2 non-locking casters:
Insert glides and casters as
previously described. The glides
should positioned towards the
front edge of the table (Figure 3).
5. For Pin-Height Adjustable Tables:
Check that both sides of the base are
set to the desired table height. The
pin should be in the center upright
hole for standard 29” tabletop height.
(Figure 4).
6. Carefully turn the table upright.
Check that the table is flat and level.
Adjust the glide heights to make
minor adjustments.
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must
be tightened securely and must be checked periodically
after assembly. Failure to assemble properly, or to secure
parts may result in assembly failure and injury.
1/4- 2 0 x 3/4" s c r e w
Figure 1
n o n - l o c k i n g
c a s t e r
l o c k i n g
c a s t e r glide
Figure 2 Figure 3
Figure 4 Part Number 13.7126
© KI 2002 Litho in USA Code KI-61331/KP402