Knight 57764.00 User manual

Label Picture Description QTY
A Chair Back 1
B Chair Seat 1
C Right Front Leg 1
D Left Front Leg 1
Label Picture Description QTY
①Bolt (M8*80) 5
②Bolt (M8*65) 5
③Washer 9
Caution : You must read this before you proceed
ACCENT CHAIR

④Spring Washer 9
⑤Allen Key 1
Before
Beginning
Assembly:
Overview
This Accent Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Accent Chair parts, the above picture is
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Chair Back（A）
Chair Seat （B）
Right Front Leg （C）
Left Front Leg （D）
Step 1.1
FRONT FACING
B
Seat Base Cover

Step 2
Step 1
Place the Chair Seat(B) Face down on a soft surface to avoid
any scratches or damages to the product.
Carefully peel away the Seat Base Cover from the edge,take
out the legs and hardwares from the Bottom of the Chair Seat
（B).
Put the Chair Back(A) onto a flat, clean, non-marring table.
Align the mounting positions of the Chair Back(A) and Chair Seat
(B).
Use your left hand to push the seat floorwards, depicted by Arrow
1.
This action helps to ensure the Chair Seat(B) is pressed towards
to the Chair Back(A) with no gap between them.
Using Bolts(①), Spring Washers(④) and Washers(③) with Allen
Key(⑤) as shown above.
Do not fully tighten Bolts.
Place the chair onto the side of a table as seen in picture 1.
Position Left Front Leg(D) into Chair Seat(B) and attach using Bolts(②), Spring
Washers(④) and Washers(③) with Allen Key(⑤).
Repeat same step to attach Right Front Leg (C) to Chair Seat(B).
Do not fully tighten Bolts.
WARNING!! DO NOT POSITION THE FRONT LEG AS SHOWN IN PICTURE 2.
Step 1.2
（1
）
（
2
）

Step 3
Step 4
THIS PICTURE SHOWS THE CHAIR BACK STAYS AGAINST THE GROUND
and THE FRONT LEGS HORIZONTAL IN MIDAIR.
WARNING!! DO NOT OVER TIGHTEN. OVER TIGHTENING COULD LEAD TO
DAMAGE OF THE PRODUCT.
TIGHTEN ONLY UNTIL SECURE AND STABLE.
Place the Accent Chair on a Level Surface to see if it wobbles.
If it wobbles, lift the accent chair some 30cm to 50cm high from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Chair freely and vertically with all four legs, hitting the ground, at the
same time.
This Drop Test will help to ensure that all Bolts, and gaps reach full alignment
status.
Test again for evenness on a Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.
Note: When tightening the Bolts, tighten sequentially. Do not tighten any Bolt or
fully and then move towards the next one. This could cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute this same drop test.
Note: If the accent chair is not stable, it could lead to damage to the product.
Place the Seat Base Cover back as shown in picture.
Smooth the Magic Tape down with your hand on all four sides at the edge of the
seat.
Make sure all parts are connected and securely locked into position.
Then stang the Accent Chair up.
Your Accent Chair is ready for use.
This Accent Chair can only be used on a flat, level surface.
①If wobble
③Test again

Do not clean furniture with harsh cleansers or polish.
Do not put hot items directly on furniture surface
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside . For indoor use only .
Do not place furniture near heating or cooling vents.
Do not place furniture under direct sunlight.
Not for commercial use. For residential use only .
Children should not climb or jump on the furniture.
Stains may be removed with mild soap solution and damp cloth.
Dust and pick-up spills using a clean, non-colored, lint-free cloth .