Knight Cubit Highrise Workstation User manual

Tools Required:
Assembly Instructions
Powered screwdriver.
Cubit Highrise
Workstation

knightgroup.co.nz
Page 2
Assembly Instructions
Cubit Highrise Workstation
Any top supplied for this unit will be a universal top and will require the
installer to correctly position & pre-drill before fixing it to the frame.
A
x 1 x 1 x 2
x 2
x 2
x 4
x 5
x 2
x 4 x 4
x 1
x 1
B D
E
F
G
H
I
JL
M
N
· To prevent possible scratches or damage, assemble
the desk upside down on a soft surface such as a
blanket, carpet or packaging.
· Attach Leg to the top assembly by using bolts, spring
washer, flat washer. Tighten using the allen wrench.
Recommended
2-person Step
x 2
K
C
x 1
x 1
C1

knightgroup.co.nz
Page 3
Assembly Instructions
Step 1
Step 2
Attach crossbeam Fto leg Ausing bolt J.
Fit adjustable feet to all legs.
Cubit Highrise Workstation
H
H
B
A
H
C
A
F
F
M
J
L
A

knightgroup.co.nz
Page 4
Assembly Instructions
Step 3
Step 3a
Insert long hex end of gear bar Eto leg A.
Attached corner leg Cto crossbeam F. Short
end of gear bar Emust be fitted into the drive
socket in the corner leg C.
Cubit Highrise Workstation
E
A
F
A
C
F
C
M
JL
C
E

knightgroup.co.nz
Page 5
Assembly Instructions
Insert short end of gear bar Eto leg B.
Step 5
Attached crossbeam Fto leg Busing bolt J.
Step 4
Cubit Highrise Workstation
F
F
JL
M
B
B
E
B
E
B

knightgroup.co.nz
Page 6
Assembly Instructions
Step 5a
Step 5b Step 6
Attach corner leg Cto crossbeam F.
Long end of gear bar E must be fitted into
the drive socket in the corner leg C.
Attach the two top rails Dto plate C1 using
bolt K.
Cubit Highrise Workstation
F
C
C
F
M
J
L
E
C
D D
K
C1

knightgroup.co.nz
Page 7
Assembly Instructions
Step 7
Step 8
Attach top rails Dto legs Aand Busing bolts I.
Insert caps Ginto crossbeam F.
Cubit Highrise Workstation
DD
B
A
D
A
N
I
G
F
B
A
G
F
A

knightgroup.co.nz
Page 8
Assembly Instructions
Fit top. Ensure that the top bars are parallel to the desk top.
Step 9
Completed
Cubit Highrise Workstation
a
a
a=a
b=b
b
b

knightgroup.co.nz
Page 9
Step 1
Step 2
Fold handle away parallel to desk top.
Pull handle lever, tilt handle lever upward and klick into crank handle.
Operation Guide
How to operate handle
1
2
3

Tools Required: Powered screwdriver.
Operation Guide
Changing crank handle
from le to right operation

knightgroup.co.nz
Page 11
Step 1
Step 3
Step 2
Step 4
A
Fit the hex drive assembly into the drive
socket on leg A.
Remove hanger bracket screws to release
the assembly, and slide the hex drive
assembly out of the leg.
Slide out crank handle and shaft.Loosen grub screws from locking collar on
leg B.
Operation Guide
Changing crank handle from le to right operation
B B
B

knightgroup.co.nz
Page 12
Slide in crank handle assembly. With crank handle fully retracted, push the locking collar hard
against the furthest bearing on the hanger bracket and tighten grub screws.
Step 7
Fit hanger bracket screws and tighten.
Step 6
Operation Guide
Changing crank handle from le to right operation
A
A

Tools Required:
Assembly Instructions
Powered screwdriver.
Cubit Highrise
Workstation Worktops

knightgroup.co.nz
Page 14
Assembly Instructions
Cubit Highrise Workstation Worktops
1800mm x 1800mm x 700mm
1800mm
700mm
700mm
1800mm
100mm
100mm
A A
A
A
*A: Ensure that the top bars are parallel to the desk top.

knightgroup.co.nz
Page 15
Assembly Instructions
Cubit Highrise Workstation Worktops
30mm
30mm
Max 125mmMin 27mm
700mm
591mm

knightgroup.co.nz
Page 16
Assembly Instructions
Cubit Highrise Workstation Worktops
1500mm x 1500mm x 700mm
1500mm
700mm
700mm
1500mm
100mm
100mm
A A
A
A
*A: Ensure that the top bars are parallel to the desk top.

knightgroup.co.nz
Page 17
Assembly Instructions
Cubit Highrise Workstation Worktops
30mm 30mm
Max 125mmMin 27mm
700mm
591mm