Kohler Elevation 76665T-E User manual

1269145-AN2-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. An in line water filter must be used with this product.
3. The highest working pressure for handspray is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure reducer is
needed. The highest water and environment temperature is 60°C. Please keep handspray away from heater, or it
may become damaged and cause injury to the user.
4. Don't remove the flow controller or the handspray will be damaged.
5. The slide bar must be mounted to stud framing supports at both the top and bottom mounting locations. Do
not use or depend on plastic wall anchors to attach the slide bar.
6. Observe local plumbing codes.
7. Recommended working pressure: 1 to 5 bar.
8. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
INSTALLATION INSTRUCTIONS
76665T-E Plus Slide Shower
ROUGH-IN DIMENSIONS
ELEVATION
76665T-E Plus Slide Shower
ELEVATION
1269145-AN2-A 4
SERVICE PARTS
**Color code must be specified when ordering.
685
580
50.4
558
602
1190001**
1190000**
1187786**
1190005**
1190000**
1190006**
1190006**
1190001**
1141216**
1061576
1061576
G1/2˝
Ø102
207
218
880010
1183428**
831727**
1030624
G1/2˝
G1/2˝
1500

1269145-AN2-A 2 1269145-AN2-A 3
INSTALLATION CHECKOUT
Ensure that all connections are tight.
Turn on the drain and main water supply and check
for leaks. Repair as needed.
Remove the handspray(15). Run hot and cold water
through hose(13) for about one minute to remove any
debris. Remove any debris from the handspray. Shut
off the main water supply. Reinstall the handspray.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
①
②
How to Install the Slide Bar
Decide on a suitable position for the slide bar
avoiding buried cables and pipes in the wall.
Mark the wall fixing hole positions for the top
of the slide bar and drill two holes to suit the
bracket(1). Insert anchors(2) into the holes.
Fix bracket(1) to wall using screws(3).
Rehearse installation of the slide bar using
screws(5), slide bar(4) and lower bracket(8).
Mark the outline of the lower bracket on the
wall and find the position of the holes. Drill
two holes to suit the lower bracket. Insert
anchors(2) into the holes.
Fix lower bracket(8) to the wall using
screws(3).
Slide the handspray holder(9) onto the bar(4).
Adjust the holder to the proper position.
Tighten the slide bar kit with screws(5).
Slide the bracket covers(6) onto the bracket,
and install the slide bar end covers(7).
How to Install the Elbow and Handspray
NOTE: To perform installation the installer
must provide a G1/2" water supply nipple(10).
Distance from the end of the nipple to the
finished wall surface should be between 10
and 13mm and perpendicular to the wall.
Apply tape or thread sealant to the threads of
the water supply nipple.
Apply a ring of plumber’s putty or sealant
around the back surface of the elbow(11).
Thread the elbow onto water supply nipple.
Adjust and make sure the outlet(12) faces
down.
Tighten hose(13) with seals(14) to elbow
outlet and to handspray(15).
Hang handspray on handspray holder(9).
1
3
5
4
9
6
6
7
7
5
2
8
3
2
14
12
12
15
13
10~13mm
10
11
15
13