KOKEN LM-078 User manual

Decubitus
Treatment Model
LM-078
Instruction Manual
Thank you for purchasing the LM-078 Decubitus Treatment Model.
Please read this Instruction Manual to ensure correct use of the product.
Store it in a safe place for easy access.
KOKEN CO., LTD.
1-4-14 Koraku, Bunkyo-ku, Tokyo 112-0004 JAPAN
URL:http://www.kokenmpc.co.jp
E-mail:[email protected]
© 2011-2020 KOKEN CO.,LTD. C-1-968-1-02-02

1
Handling and Safety Precautions
Follow these precautions to ensure safe and long-lasting use of the model.
The following precautions should be observed particularly strictly:
・ This model is made to simulate the texture of the human body. Excessive force may damage the model.
・ Do not place objects on the model. Deformation may result.
・ Follow the instructions in 4. Caring for the Model to remove dirt and smudges from the model.
・ Never use oil-based inks or paints on the model as they may cause permanent staining.
・ Store the model in a place where it will not be exposed to direct sunlight or UV rays.
Extended exposure to direct sunlight or UV rays may cause discoloration on the model.
・ This product is intended for use in standard operating environments. Do not use it in heavy industrial
settings.
・ This model uses urethane foam for some of its parts, and may be susceptible to damage from pests
that are attracted to urethane foam (such as insects in the ant family).
When storing this model, ensure that thorough measures are taken to prevent pest damage before
storing. The company will not be involved with or held liable for pest damage that occurs during
storage.
1. The contents of this instruction manual are subject to change without notice.
2. This instruction manual may not be reproduced in part or in its entirety without permission.
3. Please contact the manufacturer in the event that any errors or omissions are found in the contents of
this instruction manual.
4. This product should be used only as described in this instruction manual. In particular, the product
should not be used in any way that contravenes the precautions noted in the instruction manual.

2
Table of Contents
1. OutlineandFeatures
2. PartCompositionandNamesoftheComponents
3. HandlingtheModel
 3-1. Howtowear  
 3-2. Picture-cardstyle
4. CaringfortheModel
5. Specications

3
1. Outline and Features
Outline
This model is a reproduction of decubitus (a bedsore) on the sacral region shown in separate stages
(Stage I to IV). It can be tted to a human or a training model.
Features
・ Six layers of skin are used to represent Stage I to IV to enable understanding of the classication of
each stage.
・ The skin is made of silicone rubber for an appearance and texture that is similar to that of the
human body.
・ All six skins can be layered on together and peeled o󱐯 one by one to show the progression of
decubitus at a glance. (Picture-card style)
・ Ointment can be applied and surgical treatment can be performed.
*Do not apply ointment to the tting holder. The surface paint may peel o󱐯.

4
2. Part Composition and Names of the Components
Part Composition


 NameofComponents
① Fittingholder 
② StageISkin(flare)
③ StageIISkin(blister)
④ StageIISkin(epidermolysis)
⑤ StageIIISkin(decubituswithwhitenecrotictissue) 
⑥ StageIIISkin(decubituswithblacknecrotictissue)
⑦ StageIVSkin(decubituswithexposedbone)
⑧ Babypowder 


5
Hook and loop fasteners
(also two on the top side)
Buckle
Names of the Components
Fitting holder
Skin (underside)
Belt
Hook and loop fasteners
Skin
Hook and loop fasteners

6
3. Handling the Model
3-1. How to wear
(1) Select one of the six skins to attach to the tting holder.
Place the hook and loop fasteners together to attach in place.
(2) Wrap the belt around the hips, close the buckle, and adjust the belt length.

7
3-2. Picture-card style
(1) Layer each skin onto the tting holder in order from Stage IV to Stage I.
(2) Peel away each layer of skin at a time to observe the progression of decubitus.

8
Names of the Components Length Width Height Weight
Fitting holder Approx. 18 cm Approx. 22 cm Approx. 5 cm Approx. 300 g
4. Caring for the Model
Fitting holder
・Wipe dirt and smudges o󱐯 the tting holder with a damp cloth or gauze. Do not use
thinners, benzine, or similar solvents. Doing so may cause the paint on the surface of
the tting holder to peel.
Skin
・ Wash dirt and smudges o󱐯 the skin with water or a neutral solvent diluted with water.
・ When washing the Stage II skin (blister), be careful to avoid scraping it with your nails as
the skin may tear.
・After washing, let the model dry, then pat baby powder all over the model. For storage,
layer all six skins onto the tting holder (see 3-2. Picture-card style on p. 7).
5. Specications