Kolpin Outdoors 20049 Instruction sheet

1
© 2020 Kolpin Outdoors Inc. REV 00
Application: Verify accessory fitment at Kolpin.com.
Before You Begin: Read these instructions and check to be sure all parts and tools are accounted for. lease retain
these installation instructions for future reference and parts ordering information.
Note: If any hardware is missing, do not return to the store. Call us to help, Toll Free 1-877- 56-5746.
Polaris Ranger Off-Road Vehicle
Chainsaw Mount Kit
Product Instructions | Part No: 0049
6
4
1
3
5
2
This Kit includes:
Note: Depending on
vehicle application,
extra self-tapping
screws (not included)
can be used to secure
bed bracket (item # )
to cargo bed.
Item Qty Part Description Part Number
1 1Clamping Door Assembly -
21Mount Base Assembly -
31Fixed Hinge in -
41Turn Knob Screw, Zinc lated, M8-1.25 x 70mm LG -
51Flat Fender Washer, Zinc lated, M8 -
61Hex Locknut, Zinc lated, M8-1.25 -
73Button Screw, Zinc lated, M6-1.0 x 20mm LG, Torx Drive -
11 1Instruction Guide (not shown) -
83Hex Flange Locknut, Zinc lated, M6-1.0 -
91UTV Bed Bracket -
10 2olaris UTV Lock & Ride lunger Anchor 98510
7
8
9
10
10

2
© 2020 Kolpin Outdoors Inc. REV 00
• Metric Socket Set
• Metric Wrench Set
Tools Required:
• Safety Glasses
• Torx Driver Bit Set
Assembly Time: Approximately 12 minutes. The kit comes mostly assembled from factory, some assembly is
required. Re-torque all bolts and nuts after the first 30 minutes of use.
Important: Your Kolpin Ranger Chainsaw Mount Kit is universally designed for your vehicle. lease read the
installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For
your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.
Additional time may be required to accommodate other installed accessories.
INSTALLATION INSTRUCTIONS:
1. Attach the hinged plate assembly to the
mounting bracket (item #9) using the
three M6 button screws (item #7). Fasten
using three M6 locknuts (item #8).
Tighten to M6 specifications. (See
illustration 1-1).
2. The hinged plate assembly can be set at
45 degree angle increments to the mount
bracket to accommodate your UTV and
Saw preferences. (See illustration 1-2).
Ill. 1-1
6MM FASTENER TORQUE:
7 ft. lbs. (9.5 Nm)
Hinged
plate
assy
7
8
9
Ill. 1-2

3
© 2020 Kolpin Outdoors Inc. REV 00
INSTALLATION INSTRUCTIONS (continued):
3. Attach the two olaris UTV Lock & Ride lunger
Anchors (item #10) to the mounting bracket as shown.
(See illustration 1-3). Note, do not tighten turn
knobs at this step.
4. The Kolpin Ranger Chainsaw Mount can be installed
in many mounting positions on your cargo bed.
osition and place the mounting bracket into the cargo
bed Lock & Ride holes as shown. Tighten the turn
knobs to secure the assembly to the bed. (See
illustration 1-4).
Note, the place the plastic washers
on top of the metal bracket, under the turn knobs.
5. The Chainsaw Mount can be installed with the door
opening facing outside the Ranger bed or inside the
Ranger bed, as shown. (See illustrations 1-5 and
1-6).
Ill. 1-3
Ill. 1-4
10
Ill. 1-6Ill. 1-5

4
© 2020 Kolpin Outdoors Inc. REV 00
POLARIS GENERAL INSTALLATION
INSTRUCTIONS:
6. The Ranger chainsaw mount will fit on General
cargo beds. The General has wider bed sides
along with tapered inside walls. lace the
bracket (item #9) at the rear holes of the cargo
bed on either side. The hinged plate assembly
will fit when rotated 45° as shown. The saw or
handle tool items will be placed on outside of
bed. (See illustration 1-7).
7. The bracket (item #9) can be trimmed to allow
the saw or handle tool items to be placed inside
the General cargo bed. Mark and trim the
bracket as shown. Sand and paint the exposed
metal with black paint. The bracket can then be
placed with hinged plate assembly facing
towards interior of General bed, into many of the Lock
& Ride holes. (See illustrations 1-8, 1-9 and 1-10).
Ill. 1-7
Ill. 1-10
9General
Tailgate
Ill. 1-8
Ill. 1-9
Modified
bracket

5
© 2020 Kolpin Outdoors Inc. REV 00
OPERATIONAL USE INSTRUCTIONS:
8. The Chainsaw mount is designed to carry your saw safely and securely while
keeping your UTV bed open for other necessities. The mount is also designed to
carry yard tools with a handle, example shovel, in the round groove opening on
hinged door (item #1). (See illustration 1-11).
9. The hinged plate assembly has a hand turn knob (item #4) that provides clamping
force to hold saw or shovel. To open, loosen the hand knob and pivot the hand
knob to release the hinged door plate. (See illustration 1-12). Note, the flanges on
the front plate are designed to help keep branches from hitting and possibly
opening the hand knob.
10. lace the saw into the hinged door assembly and push the front plate closed.
Swing the hand knob into the lost in the front plate and tighten securely. Tighten
the turn knobs to secure the assembly to the bed. (See illustrations 1-12, 1-13 and
1-14).
Note, the large flat washer (item #5) provides bearing surface between
the hand knob and hinged door.
11. The saw bar can be clamped by the door on either end of the base or in the
middle. More clamping area is found on each end. (See illustrations 1-13, 1-14 and
1-15).
Ill. 1-12
Ill. 1-11
4
CAUTION: When loosening the clamping door turn knob, the
door may swing open causing the saw to fall out. Make sure to
hold onto saw when opening the saw clamping door.
5
Ill. 1-13 Ill. 1-14 Ill. 1-15

6
© 2020 Kolpin Outdoors Inc. REV 00
For additional assistance, please contact Kolpin customer service department at
[phone] or [phone] or email [email protected]
One Year Limited Warranty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts
found upon examination by Kolpin to be defective in material, workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin
determines that the product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise
Authorization (RMA) number and shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or
other causes beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or
hardware are designed to fail when the equipment is over-stressed. arts that are lost due to loosening and improper maintenance
are not covered under warranty. This warranty does not cover removal or reinstallation labor fees of the plow system and related
components.
eripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is
general in nature and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.
Use and Care Information:
• Check the accessory mounts frequently and retighten hardware if necessary.
• Replace this accessory with a new one if it is damaged.
• Never use petroleum solvents such as gasoline, thinner, benzene, acid or alkaline cleaners.
Ill. 1-16
OPERATIONAL USE INSTRUCTIONS
(continued):
12. You are able to mount your saw so that the
power head is not sitting on the area
provided as shown. It is best if your power
head is sitting on the foam pad, but in some
instances this may not work, and has
proven no loss in performance of the saw
mount. (See illustration 1-16).