KStrong Kapture Essential Operator's manual

THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODEL:
RESTRAINT LANYARD
USER INSTRUCTION MANUAL
AFL406111, AFL406151, AFL406301, AFL406341, AFL406601
EN 354:2010
ESSENTIAL

Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the user's
reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
1. INTRODUCTION : These Restraint Lanyards are classed as a Personal Protective Equipment (PPE) by the European PPE Regulation (EU)
2016/425 and has been shown to comply with this Regulation through the Harmonized European Standard EN 354:2010. The forked
lanyards are tested in accordance to VG11.
These Lanyards are designed to minimise the risk of/provide protection against the danger of falling from heights. However, always
remember that no item of PPE can provide full protection and care must always be taken while carrying out the risk related activity.
2. DESCRIPTION:
3. PERFORMANCE AND LIMITATIONS OF USE: The Lanyards have been tested in accordance with EN 354:2010 and have achieved the
following performance levels:
EN 354:2010 test
Clause 4.1 Design and Ergonomics
Clause 4.2 Material & Construction
Clause 4.5 Static strength
Result/Comment
Achieves required performance requirement
Achieves required performance requirement
Achieves required performance requirement
4. POSSIBLE USAGE: These Lanyards can be used as a part of a fall arrest system or as a part of a restraint system. If using as a part of fall
arrest system, a suitable anchor point (above the user's head, as least 12kN) shall be used. Attachments between these lanyard and the
anchor points and other equipment shall be made using Karabiners as per EN 362:2004. An Energy Absorber to EN 355:2002 shall be used in
conjunction with this lanyard. Restraint Adjustable Rope Lanyards are incorporated with metal adjuster to adjust the length of the Lanyard.
5. IMPORTANT NOTICE:
ŸTotal length of a sub system with a lanyard including an energy absorber, terminations and connectors shall not exceed 2.0m.
ŸMaximum adjustable length for the Adjustable Rope Lanyards will also be upto 2.0m only.
ŸDo not use a lanyard without an energy absorber for fall arrest systems.
ŸThe strength of the anchor device should be greater than 12kN and the anchor point should be situated above the user's head.
ŸConnect the lanyard to the anchorage point using the connector provided at one end. (If connector not provided, use Karabiners
complying to EN 362:2004).
ŸThe other end should be connected to the attachment element of the full body harness incorporating an energy absorber in case used
for fall arrest systems.
ŸTo optimize protection, in some instances it may be necessary to use the lanyard with suitable other components. In this case before
carrying out the risk related activity, consult your supplier to ensure that all components are compatible and suitable for your
application.
ŸIf the risk assessment carried out before the start of work shows that loading in the case of a user over an edge is possible, appropriate
precautions must be taken.
02
AFL406111
AFL406151
AFL406301
AFL406341
AFL406601
Essential
Essential
Essential
Essential
Essential
Restraint Single Leg Twisted Rope Lanyard
Restraint Single Leg Twisted Rope Lanyard
Restraint Resistant Adjustable Webbing Lanyard
Restraint Twin leg Resistant Adjustable Webbing Lanyard
Restraint Twin leg Twisted Rope Lanyard
PRODUCT CODE CATEGORY PRODUCT DESCRIPTION MAX LOAD RATED
140kg
140kg
140kg
140kg
140kg

6. MATERIAL USED:
ŸTwisted Rope Lanyards - Polyamide
ŸWebbing Lanyards - Polyester
ŸKernmantle Rope Lanyards - Polyamide
7. PRE -CHECK USE:
ŸSince all lanyards are made of polymers, the performance of which gets affected by temperatures, effect of sharp edges, electrical
conductivity, chemical regents, cutting, abrasion, UV degradation etc, it is advised to consult your supplier for use in above extreme
conditions.
ŸEnsure before & during use that a rescue plan is in place to rescue the user after a fall has occurred.
ŸThese lanyards should only be used by a trained and/or otherwise competent person or the user should be under the direct supervision
of such a person.
ŸThe user should minimize the amount of slack in the lanyard near a fall hazard.
ŸThese lanyards cannot be choke hitched.
ŸTwo separate lanyards each with an energy absorber should not be used side by side (i.e. parallel), for such instance usage of double
leg lanyard is recommended.
9. WARNING:
ŸIt is essential to verify that the medical condition of the user is fit to use the lanyards in normal and emergency use.
ŸDo not make any alterations or additions to the equipment without the manufacturer's prior written consent and that any repair shall
only be carried out in accordance with the manufacturer's procedures.
ŸWhile using the lanyard, ensure that the fall is not more than 2m i.e. the distance between the anchor point & the final position of the
user after the fall has occurred.
ŸLanyard should be the personal property of its user.
ŸIt is important to check before use any dangers that may arise by the use of combinations of items of the equipment in which the safe
function of any one item is affected by or interferes with the safe function of another.
ŸCarry out a pre-use check of the lanyard, to ensure that it is in a serviceable condition and operates correctly before it is used.
ŸInspect all the rope or webbing of lanyard for cuts/abrasion marks. Also check all connectors of the lanyard for proper mechanical
functioning & effects of corrosion or mechanical deformation if any on parts of the connectors in the lanyard.
ŸWithdraw from use any lanyard for which any doubt arises about its condition for safe use or in the event, a fall has been arrested by it.
ŸIf the lanyard is used in a fall arrest system, it is advisable to connect only to the dorsal attachment D-Ring of the harness.
ŸIf lanyard is used in fall arrest system, it is essential for safety that the anchor device or anchor point is always positioned, and the work
carried out in such a way, as to minimize both the potential for falls and potential fall distance. Ensure that the anchor point is above the
user's head.
ŸOnly a full body harness complying to EN 361:2002 shall be used as a body holding device within the fall arrest system.
ŸIf used within fall arrest systems, it is essential to verify the free space required beneath the user at the work place before each
occasion of use, so that, in the case of a fall, there will be no collision with the ground or other obstacles in the fall path.
ŸIf the product is resold outside the original country of destination, the reseller shall provide instructions for use, for maintenance, for
periodic examination and for repair in the language of the country in which the product is to be used.
ŸEnsure the Medical condition of the user does not affect his safety in normal and emergency use.
ŸA rescue plan shall be in place to deal with any emergencies that could arise during the work.
ŸIt is essential for the safety of the user that if a product is re-sold outside the original country of destination the reseller shall provide
instructions for use for maintenance, for periodic examination and for repair in the language of the country in which the product is sold.
ŸThe equipment shall not be used outside its limitation, or for any purpose other than that for which it is intended.
ŸThe device should be used with appropriate combinations only. The user should not make any combination which compromises safe
function of any other devices used in combination or entire fall protection system or rescue system.
ŸWhen adjusting the length of a lanyard to avoid the risk of a fall, the user should not move into an area where there is a fall hazard.
8. ANCHORAGE INSTRUCTION: The strength of the anchor device should be greater than 18kN (for Textile) & 12kN (for Metal).
03

10. INSTRUCTIONS FOR MAINTENANCE:
ŸCleaning Procedure: In case of minor soiling, wipe the lanyard with cotton cloth or a soft brush. Do not use any abrasive material. For
intensive cleaning wash the lanyard in water at a temperature not more than 40ºC using a neutral detergent (pH7). Do not use acid or
basic detergents.
ŸDrying Procedure: If the lanyard becomes wet, either from by in use or when due to cleaning, it should be allowed to dry naturally and
shall be kept away from direct heat.
ŸStorage Procedure: When not in use, store the lanyard in a well-ventilated area away from extremes of temperature. Never place
heavy items on top of it. If possible, avoid excessive folding and preferably store it hanging vertically. If the product is wet, allow it to dry
fully before placing it into storage. It is preferred that the product be transported in its original packing. However if not available, it may
be stored in an air tight bag & transported.
11. PERIODIC EXAMINATION:
ŸThe lanyards need to periodically examined because the safety of the user depends upon the continued efficiency & durability of the
lanyard.
ŸIt is important to examine it at least once in every 12 months.
ŸPeriodic examination is to be conducted by a competent person and strictly in accordance with the manufacturer's periodic
examination procedures.
ŸPeriodic examination also requires checking the legibility of the product markings.
12. INSTRUCTIONS FOR REPAIR: If the product becomes damaged, it will NOT provide the optimum level of protection, and therefore should
be immediately removed from service. Never use the damaged product. Repair is only permitted by the manufacturer or a nominated repair
centre or individual approved by the manufacturer.
04

13. MARKING ON PRODUCT: The Lanyard is marked with:
(i) The CE mark showing that the product meets the requirements of the
European PPE Regulation (EU) 2016/425
(ii) Trademark of the manufacturer
(iii) Type or product code
(iv) Month and Year of Manufacture
(v) UID for traceability
(vi) Number of the standard
(vii) Material
(viii) Length
(ix) Identification of the manufacturer and address
(x) Number of the ongoing assessment body
(xi) Pictogram that indicates to read the instructions
MARKING
14.
ŸSpread the lanyard on a table / flat surface.
lanyard
lanyard
HOW TO DISPOSE A LANYARD: lanyard
any wear and tear, dispose the lanyard immediately.
Follow the steps for Disposal:
ŸSegregate the equipment in three different crates for placing components in
them respectively as- Textile, Metal and Plastic.
ŸInspect the wear & tear present on the .
ŸNow, using a sharp pair of scissors first cut the Textile and dismantle the
lanyard.
ŸNow remove the metal & plastic components separately from the .
ŸPut the Textile, Plastic & Metal components in their respective plastic
crates.
When the becomes unfit or in case of
05
EN 354:2010
Essential Restraint
12mm Twisted Rope
Lanyard
Model : AFL406111
Material : Polyamide
Length : 2.0 m
DOM : MM/YYYY
UID : XXXXXXXXXXXX
KStrong Inc.,
150 N. Radnor Chester Road Suite F200 Radnor,
Pennsylvania 19087 United States
KStrong.com Made In India
QRCODE
Max. Rated Load
(Including all tools)
140
kg
(i)
(ii)
(iii)
(iv)
(v)
(vi)
(vii)
(x)
(xi)
(ix)
(viii)

LIFESPAN: The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the
product: intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure,
abrasions, cuts, violent impacts, bad use or maintenance.
DISCLAIMER: Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of
shipment and seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible
for any loss, damage or injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD
06

07

Certification Body :
SATRA Technology Europe Ltd, Bracetown Business Park, Clonee, Dublin D15 YN2P Ireland (Notified Body 2777)
Ongoing Assessment Body:
SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland (Notified Body 0598)
For EU Declaration, please visit https://kstrong.com/asia/eu-declaration-form/
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact number : 1-833-KSTRONG
AKS/ /110121/V1AFL406111