KStrong AFL405101 Operator's manual

THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODELS:
WORK POSITIONING LANYARDS
AND POLE STRAPS
USER INSTRUCTION MANUAL
AFL405101, AFL405111, AFL405201, AFL405211 AND AFL405351
EN 358:2018

CODE
AFL405101
AFL405111
AFL405201
AFL405211
AFL405351
KAPTURE ELITE
KAPTURE ELITE
KAPTURE ELITE
KAPTURE EPIC
KAPTURE EPIC
WORK POSITIONING 14MM TWISTED ROPE ADJUSTABLE LANYARD
2M C/W STEEL KARABINER AT BOTH ENDS
WORK POSITIONING 14MM TWISTED ROPE LANYARD
2M C/W GRIP ADJUSTER STEEL KARABINER AT BOTH ENDS
WORK POSITIONING ADJUSTABLE WEBBING LANYARD
2M C/W STEEL KARABINER AT BOTH ENDS
POLE STRAP (2.0M) C/W WITH ADJUSTER AND
SNAP HOOKS AT EACH END
WORK POSITIONING 12MM KERNMANTLE ROPE LANYARD
2M C/W ALUMINUM ADJUSTER AND KARABINER AT ONE END
AND KNOT AT OTHER
CATEGORY DESCRIPTION
Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the user's
reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
EN 358:2018 test
Clause 4.1 Design, Construction and Ergonomics
Clause 4.4 Static Strength
Clause 4.5 Dynamic Strength
Result/Comment
Achieves required performance requirement
Achieves required performance requirement
Achieves required performance requirement
01
1. INTRODUCTION: The Work Positioning Lanyards and Pole Straps are classed as a Personal Protective Equipment (PPE) by the European
PPE Regulation (EU) 2016/425 and have been shown to comply with this Regulation through the Harmonized European Standard BS
EN 358:2018.
2. INSTRUCTIONS: The Work Positioning Lanyards and Pole Straps is designed to minimise the risk of/provide protection against the danger
of falling from heights. However, always remember that no item of PPE can provide full protection and care must always be taken while
carrying out the risk related activity.
3. PERFORMANCE AND LIMITATIONS OF USE: The Work Positioning Lanyard has been tested in accordance with EN 358:2018 and has
achieved the following performance levels:
4. PRODUCT DESCRIPTION:
However the maximum length of the lanyard is limited to 2.0 mtrs only.
The lanyard can be attached to the attachment elements of the work positioning belts using harnesses and belts connector. It can also
be permanently incorporated on to a work positioning belt, but by the manufacturer only.
The Work positioning Lanyard is an adjustable lanyard whose length can be adjusted using length adjuster

02
5. INSTRUCTIONS TO BE FOLLOWED BEFORE USE: Inspect the for any damage to the Rope
or Webbing. Do not use the Work positioning lanyard in case of any damage or defectiveness. Ensure the compliance with recommendation
for use as applicable to the combination with other components ensure the connector is correctly attached to the attachment as per
EN362:2004) of the Work positioning system and specified on the identification card for the Work positioning system or component. Ensure
the connector is correctly attached and locked to the attachment as per EN362:2004
Note: The Work positioning lanyard should be a personal property of its user. In use, the lanyard should be kept taut and free movement is
restricted to a maximum of 0.60 m.
Work Positioning Lanyards and Pole Straps
6. HOW TO USE:
KAPTURE ELITE WORK POSITIONING (AFL405101)
The Lanyard have two ends. One end is a small spliced eye while the other end is loop formed by the rope and the adjusting
ring. To differentiate between the two we shall address the two ends as EYE and LOOP respectively.
STEP 1: Attach the karabiner to the EYE and the LOOP.
STEP 2: Now connect the lateral attachment element of your work positioning belt to one end, loop the lanyard twice
around the vertical support and attach the connector to the other attachment element of the work positioning belt.
Adjust the length of the lanyard using the Ring type adjuster.
Loop
Eye Karabiner
Karabiner
KAPTURE ELITE WORK POSITIONING (AFL405111)
The Lanyard has two attachment ends. One end is a small spliced eye while the other end is the attachment ring of the
mechanical device.
STEP 1: Attach the karabiner to both attachment ends of the lanyard.
STEP 2: Now connect the lateral attachment element of your work positioning belt to one end, loop the lanyard twice
around the vertical support and attach the connector to the other attachment element of the work positioning belt.
Adjust the length of the lanyard using the mechanical device.
Karabiner
Karabiner
Loop
Eye

Eye Loop
Karabiner Karabiner
Ring type adjuster
KAPTURE ELITE WORK POSITIONING (AFL405201)
The Lanyards have two ends. One end is a stitched loop while the other end is loop formed by the webbing and the adjusting
ring. To differentiate between the two, we shall address the two ends as EYE and LOOP respectively.
STEP 1 : Attach the karabiner to the EYE and the LOOP.
STEP 2 : Now connect the lateral attachment element of your work positioning belt to one end, loop the lanyard twice
around the vertical support and attach the connector to the other attachment element of the work positioning belt.
Adjust the length of the lanyard using the Ring type adjuster.
KAPTURE EPIC POLE STRAP (AFL405211)
The lanyard has Steel snap hooks stitched at both the ends along with a length adjuster.
Connect the lateral attachment element of your work positioning belt to one end, loop the lanyard twice around the
vertical support and attach the connector to the other attachment element of the work positioning belt.
Adjust the length of the lanyard using the length adjuster.
Positioning Lanyard as would be used by a user.
Ensure that the lanyard anchorage point is maintained at or above waist level.
Looping the lanyard twice is recommended to prevent it from slipping down.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Roller Buckle Steel Snap Hook
KAPTURE EPIC WORK POSITIONING (AFL405351)
The Lanyards have two ends. One end is a stitched loop with thimble while the other end is the captive eye of Rope Grab.
STEP 1: Attach the karabiner to the EYE and the LOOP .
Warning: Make sure that the karabiner is not attached to the stop knot. It needs to be attached to the captive eye of the rope grab
only.
STEP 2: Now connect the lateral attachment element of your work positioning belt to one end, loop the lanyard once or twice
around the vertical support (depending upon available length) and attach the connector to the other attachment element of the
work positioning belt. Adjust the length of the lanyard using the Rope Grab.The Lanyard is not suitable for fall arrest purpose and
it may be necessary to supplement arrangements for work positioning or restraint with collective means (e.g. safety nets) or
personal means (e.g. fall arrest system in accordance with EN 363) of protection against falls from height.
The user should position and/or adjust the work positioning lanyard in such a way that the anchorage point is maintained at or
above waist level; the lanyard is kept taut; and free movement is restricted to a maximum of 0.6 m.
Stop Knot
Thimble
Kernmantle Rope
Karabiner (AFC601100)
Rope Grab (AFG801011)
03

NOTE: Work Positioning Lanyards and Pole Straps as would be used by
a user. Ensure that the lanyard anchorage point is maintained at or above
waist level. Looping the lanyard twice is recommended to prevent it from
slipping down.
User Held in
Position
Karabiner
Work
Positioning
Lanyard /
Pole strap
Lateral
Attachment
Element
7. ANCHORAGE INSTRUCTION:
The strength of the anchor device should be greater than 18kN (for Textile) & 12kN (for Metal).
8. CLEANING AND DRYING INSTRUCTIONS:
In case of minor soiling, wipe the Work positioning lanyard with cotton cloth or a soft brush.
Do not use any abrasive material.
For intensive cleaning wash the Work positioning lanyard in water at a temperature not more than 40ºC using a neutral detergent
(pH7).
Do not use acid or basic detergents.
The Work positioning lanyard should be allowed to dry by itself and be kept away from open fire or any other source of heat.
Avoid direct sunlight.
9. PROTECTION OF THE WORK POSITIONING LANYARD DURING USE: The Work positioning lanyard shall be protected against the
following factors:
Ageing due to cold, heat, moisture and direct sunlight.
Deterioration due to Chemicals such as oils, acids, solvents and sea water.
Inappropriate choice of the Work positioning lanyard in relation to the risk concerned.
Inappropriate combination with other equipment.
Use by a person lacking sufficient training and safety awareness.
Unnecessary Physical loading (static or dynamic), e.g. by lifting heavy objects such as sections or plates etc.
Improper use by untrained persons.
Deterioration through mechanical wear, water or soiling.
Inappropriate storage, maintenance or cleaning.
10. PROTECTION AGAINST HAZARDS DURING USE:
When using the Work positioning lanyard it has to be made sure that the wearer does not trip over flexible anchor lines or Lanyard. A rescue
plan is to be set up before use.
11. STORAGE INSTRUCTIONS: The Work positioning lanyard should be stored in dry not too hot rooms, kept away from heaters & corrosive
substances and protected against direct sunlight.Follow the storage procedures rigorously, including all necessary preventative
requirements where environmental or other factors could affect the condition of components, e.g. damp environment, sharp edges,
vibration, ultra-violet degradation. When the equipment becomes wet, either from being in use or when due to cleaning, it should be allowed
to dry naturally, and should be kept away from direct heat.
12. ACCESSORIES: We do not produce any accessories for the Work positioning lanyard and strongly recommend not to use Work positioning
lanyard with any substandard accessory. The user shall be responsible for any damage occurring under such circumstances.
13. RESTRICTION OF USE: The Work positioning lanyard should be used for Positioning only. The Work positioning lanyard should not be
used in highly acid or basic environments.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
04

14. WARNING:
A full body harness is the only acceptable body holding device that can be used in a fall arrest system.
ŸThe device must only be used by a trained and competent person, or by a person subject to a level of competent supervision.
ŸIn case of any doubt arising about the safety of the Work positioning lanyard, it should be replaced immediately in consultation with a
competent person. Do not use a Work positioning lanyard which has already arrested a person's fall.
ŸRegularly check fastening and/or adjustment elements during use.
ŸThe lanyard is not suitable for fall arrest purposes and it may be necessary to supplement arrangements for work positioning or
restraints with collective means (e.g. Safety Nets) or personal means (e.g. fall arrest systems in accordance with EN 363) of protection
against falls from height.
ŸEnsure the Medical condition of the user does not affect his safety in normal and emergency use.
ŸA rescue plan shall be in place to deal with any emergencies that could arise during the work.
ŸIt is essential for the safety of the user that if a product is re-sold outside the original country of destination the reseller shall provide
instructions for use for maintenance, for periodic examination and for repair in the language of the country in which the product is sold.
It is also essential for the safety of a user to use an anchor point positioned at or above waist level for work positioning purpose.
ŸThe equipment shall not be used outside its limitation, or for any purpose other than that for which it is intended.
ŸThe device should be used with appropriate combinations only. The user should not make any combination which compromises safe
function of any other devices used in combination or entire fall protection system or rescue system.
While using a work positioning system, the user normally relies on the equipment for support, therefore it is essential to consider the
need of using a back-up e.g. fall arrest system.
Marking on the lanyard must include the maximum lanyard length.
15. HOW TO DISPOSE :
When the lanyard becomes unfit or in case of any wear and tear, dispose it immediately.
Follow the steps for Disposal:
ŸMake the three plastic crates namely- Textile, Metal & Plastic for placing the respective components of the lanyard.
ŸSpread the lanyard on a table / flat surface.
ŸInspect the wear & tear present on the lanyard.
ŸIf any wear and tear is observed, dispose the lanyard using a sharp pair of scissor; first cut the Textile and dismantle the lanyard.
ŸPut the Textile, Plastic & Metal components in their respective plastic crates.
17. INSTRUCTIONS FOR PERIODIC EXAMINATIONS:
ŸIt is necessary to carry out regular periodic examinations. The safety of the users depends upon the continued efciency and
durability of the equipment.
ŸThe product should be necessarily examined taking account of such factors as legislation, equipment type, frequency of use, and
environmental conditions as the safety of the user depends upon the continued efciency and durability of the equipment.
The personal protective equipment shall be examined at least every 12 months. The periodic examination can only be carried out
by the manufacturer or his authorized representative.
The comments should be included in the check card of the equipment. After the periodic examination, the next due date for
periodic examination will be determined.
During periodic inspection it is necessary to check the legibility of the equipment marking.
ŸTo check metals for sharp edge, burs, corrosion, bent prole distortion and opening & closing or such mechanisms for which that is
intended for.
To check webbings/ ropes for breakage, untwisting, frayed, burn, paint, excessive dust or soiling, cut, exposure to chemical or any
such elements which can harm the webbing/ropes or can result in the compromised performance of the entire system or device in
which it is used.
Shall be discarded as per procedures given under point instructions for disposal.
The required annual examinations will validate the correct functioning of the equipment.
It is compulsory that the equipment is examined by the manufacturer or his authorized representative at least once a year.
In case that it have been used to arrest a fall, the equipment must be withdrawn from use.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
05

06
140
kg
140
kg
140
kg
140
kg
16. MARKING ON PRODUCT:
The produts are marked with:
(I) The CE mark showing that the product meets the
requirements of the European PPE Regulation (EU)
2016/425 and number of the ongoing assessment body
(ii) Identification of the manufacturer and address
(iii) Type or product code
(iv) Month and Year of Manufacture
(v) Pictogram that indicates to read instructions
(vi) UID for Traceability of Product
(vii) Material
(viii) Length
(ix) Pictogram that shows max. rated load
(x) Number of the standard
MARKING
140
kg
i
ix
v
ii
iii
vii
vi
iv
viii
x

AKS- 21AFL405101- 1020-V1
Certification Body:
SATRA Technology Europe Ltd, Bracetown Business Park, Clonee, Dublin D15 YN2P Ireland (Notified Body 2777)
Ongoing Assessment Body:
SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland (Notified Body 0598)
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact number : 1-833-KSTRONG
LIFESPAN: The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the product:
intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure, abrasions, cuts,
violent impacts, bad use or maintenance.
DISCLAIMER: Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of
shipment and seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible for
any loss, damage or injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD
For EU Declaration, please visit https://kstrong.com/asia/eu-declaration-form/