KStrong AFX203001 Operator's manual

THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODEL:
EDGE PROTECTOR
USER INSTRUCTION MANUAL
AFX203001

01
Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the user's
reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
1. INTRODUCTION: This Angle Shaped Edge Protector AFX203001 protects the rope from abrasion against an edge. The edge ring guides on
the angle of the edge-protector to keep multiple anchor lines from getting entangled over the edge.
2. INSPECTION: Visually inspect the system before each use to ensure that it is in a serviceable condition and is operating correctly. If during
inspection, doubts are raised about the safety of the system or a component, these should be replaced either by the manufacturer or a
competent person.
To use this product follow the steps given below-3. INSTRUCTIONS FOR USAGE:
STEP-1
Tie a Tag Line to the Edge Protector Hole
STEP-2
0
Place the Equipment on the edge at 90 angle
STEP-3
Connect the Tag Line with the Pre- Fixed Anchor Point
STEP-4
Pass the Rope Through the equipment
4. LIMITATIONS
ŸThe product should be th roperty of its user.
It should not be used in highly acidic or basic environment.
5. REPAIR: If the product becomes damaged, it will NOT provide the optimum level of protection, and therefore should be immediately removed
from service. It needs to be inspected to see if it is replaced or repaired. Never use the damaged product. Repair is only permitted by the
manufacturer or a nominated repair centre or individual approved by the manufacturer.
6. CLEANING: In case of minor soiling, wipe the product with cotton cloth or a soft brush. Do not use any abrasive material. For intensive cleaning
0 0
wash the product in water at a temperature between 30 C to 60 C by using a neutral detergent (pH+7). The washing temperature should not
0
exceed 60 C. Do not use acid or basic detergents.
e personal p
Ÿ

02
7. STORAGE AND TRANSPORT: When not in use, store the product away from heavily acidic or basic environment. Never place heavy items on
top of it. Also ensure that it is stored away from chemically hazardous environment preferebly storage should be in dry environment.
8. WITHDRAWAL FROM USE: If the system has been used from a long time and have suffered wear and abrasion due to regular usage, it should
be removed from service and resend to the manufacturer or a competent repair centre for servicing and re test.
LIFESPAN: The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the product:
intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure, abrasions, cuts,
violent impacts, bad use or maintenance.
DISCLAIMER: Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of
shipment and seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible for
any loss, damage or injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD

AKS- -280221-v1AFX203001
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact Email: [email protected]