Kuryakyn 7158 User manual

LUGGAGE RACK RISERS, GLOSS BLACK 7158
Page 1
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the contents described herein may negatively affect product per-
formance and functionality or damage the product itself or the product to which it is being attached.
STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn
IGN OFF.
STEP 2 If equipped, put the motorcycle on the center-stand.
STEP 3 Disconnect the battery.
STEP 4 Open the top trunk lid; remove the 15 screws securing the plastic underside of the lid. Save the hardware for later use. See Pic. 1.
STEP 5 Remove the two screws on each latch ring. See Pic. 1.
STEP 6 Pull the trunk lid underside down; disconnect the multi-pin connector. See Pic. 2.
STEP 7 Set aside the trunk lid underside.
STEP 8 Remove the existing luggage rack and hardware; save for later use.
NOTE: It is recommended that the existing rack mount holes in the trunk lid be enlarged with a 1/4” drill bit to allow for alignment and
ease of installation.
For installation where a trunk spoiler is already installed, ensure that there is enough clearance to install rack risers before
drilling any holes.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
4 Luggage Rack Spacer
1 Hardware Kit including:
2 #10-24 x 2” BSCS
2 #10-24 x 1-3/4” BSCS
4 Spacer, .2 x .75 x .125
4 Spacer, .2 x 1.00 x .125
4 1/4” SAE Flat washer
You will also need:
Phillips screwdriver, set of hex wrenches, 1/4” drill bit and drill
Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.
7158-11MC-0216
Thank You For Choosing Küryakyn!
Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices
regarding the installation, use, and care of this product.
These installation instructions contain important information. Ensure that the end user receives this copy and is
aware of its importance for future use.

Page 2
STEP 9 Insert a 1 3/4” screw, washer and small rubber spacer through the under-
side of the trunk lid in one of the front holes. See Fig 1.
STEP 10 Install a large rubber spacer and rack riser over the protruding end of the
screw on the topside of the trunk lid. See Pic. 3 and 4 and Fig. 1.
STEP 11 Repeat Steps 9 and 10 for the other front hole.
STEP 12 Carefully hold the rack in position and begin the threads of the screws into
the rack; do not fully tighten the screws. Allow the rack to “hang” while the
rear screws are prepared. See Pic. 5.
STEP 13 Install a 2” screw with washer and small rubber spacer through one of the
rear holes in the trunk lid.
STEP 14 Place large rubber spacer and rack riser over the protruding end of the
screw; repeat for the other side.
STEP 15 Thread the rear screws into the rack. Do not fully tighten screws.
STEP 16 Close trunk lid; center rack on lid
STEP 17 Carefully open the lid; tighten screws.
STEP 18 Reconnect multi-pin connector; reinstall trunk lid underside.
STEP 19 Reinstall 15 screws securing trunk lid underside to lid.
STEP 20 Reinstall latch rings and screws.
STEP 21 Check for proper lid operation.
Latc Latc
P
PIC 1
Depresstabandpullconnectorout
Mul‐pinconnector
P
PIC 2
Rackleg.
Rackriser.
Large
rubber
spacer
Trunklid
Smallrubber
spacer
Washer
Screw
FIG 1

Page 3
It is the end user’s responsibility to ensure that all fasteners (including pre-assembled) are tightened before
operation of the motorcycle. Kuryakyn will not provide warranty coverage on products or components lost or
damaged due to improper installation or lack of maintenance. Periodic inspection and maintenance are
required on all fasteners.
P
Largerubberspacer
Rack
riser
PIC 3
Screw
pro‐
truding
from
under‐
sideof
trunk
Large
rubber
spacer
P
PIC 4
Refer to PIC 1. Using warm
soapy water and a clean
rag, remove all dirt and
debris from the installation
area; allow the area to dry
completely. Wipe the instal-
lation area with the included
alcohol pad to remove any
wax or polish; allow the
area to dry completely.
STEP 3 Test fit the Accent as
Refer to PIC 4. Align the Bracket slots with
the intake flange and gas-
Donotghten
screwsalltheway;
lethanginfront
hole.
P
PIC 5