Kuryakyn 3181 User manual

PartS Included
1 License Plate Backplate
1 License Plate Z-Bracket
1 License Plate Frame
1 Hardware Kit
4 ¼-20 x ¾” Flat Screws
5 ¼-20 Acorn Nuts
5 ¼” Split Lock Washers
1 ¼-20 x ½” Socket Head Cap Screw (SHCS)
2 10-24 x ½” Button Socket Cap Screws (BSCS)
2 10-24 Acorn Nuts
2 #10 Split Lock Washers
1 1” x 3” x 0.1” Single Side PS
1 Installation Instructions
Please read and understand entire instructions before starting installation.
thank you for chooSIng küryakyn!
In order to Protect you and otherS from PoSSIble Injury
and/or ProPerty damage or loSS, PleaSe Pay cloSe attentIon
to all InStructIonS, warnIngS, cautIonS and attentIon noteS
regardIng the uSe and care of thIS Product.
WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE
CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR
SERIOUS INJURY.
CAUTION! This indication alerts you to the fact that ignoring the contents described herein
can result in potential injury or material damage.
ATTENTION! This indication alerts you to the fact that ignoring the contents described herein
may negatively affect product performance and functionality.
toolS SuggeSted
Set of Hex Wrenches, Combination Wrenches, Socket Set with Extensions and Ratchet
StrIctly obServe the followIng guIdelIneS In order to uSe the
Product ProPerly and avoId PotentIally dangerouS accIdentS.
Procedure
SteP 1 Read and understand all steps in the instructions before starting the installation. Park
the motorcycle on a hard, level surface; turn off the ignition and allow the engine to cool.
ATTENTION! A factory service manual may be helpful in performing this installation. Do not
attempt to perform this installation if you are not confident in your ability to complete all of the
steps in the procedure; consult a trained technician.
3181-11HD-0709
curved laydown lIcenSe Plate mount 3181
fItS: ’05-uP flStn SoftaIl deluxe, ’05-’07 flStSc SoftaIl SPrInger claSSIc and
’97-’03 flStS herItage SPrInger

INSTALLATION
SteP 2 Remove the black cover located inside the rear fender by pulling at the bottom and releasing the
top of the cover from the clip.
SteP 3 Remove the license plate backing plate and hardware from the taillight housing and
support arm.
SteP 4 Remove the taillight housing by removing the 3 screws (PIC 1) located on the front of the
taillight.
SteP 5 Remove the hardware securing the stock support arm. It will be necessary to reach the
hardware inside the fender.
SteP 6 Install the new Z-Bracket (PIC 2) in place re-using the stock hardware.
SteP 7 Secure the new License Plate Backplate (PIC 3) to the taillight housing using the 10-24
BSCS, 10-24 Acorn Nuts and #10 Split Lock Washers.
SteP 8 Install the taillight/backplate assembly to the bike. Secure with the 3 screws removed in
Step 4.
SteP 9 Install the ¼-20 x ½” SHCS through the top hole in the back plate and into the Z-
Bracket. Secure with a ¼” Split Lock Washer and Acorn Nut.
SteP 10 Install your license plate to the backplate and place the license plate frame over the
assembly and secure with the ¼-20 Flat Screws, Flat Washer and Acron Nuts.
SteP 11 Tighten all fasteners
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners (including pre-
assembled) are tightened before operation of the motorcycle. Küryakyn will not issue a warranty on
components lost due to improper installation. Periodic maintenance may be required.
Page
2
lIcenSe Plate mount
PIC. 1
PIC. 2
PIC. 3
PIC. 4