Life Gear Evoke User manual

Evoke Magnetic Upright Bike
Item No.: 20290
Owner’s Manual
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2011, Sept.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 1
SAFETY INSTRUCTIONS ------------------------------------------------------------- 2
ADJUSTMENTS -------------------------------------------------------------------------- 3
OPERATING THE COMPUTER ------------------------------------------------------ 3
PARTS LIST ------------------------------------------------------------------------------- 5
HARDWARE PACKING LIST --------------------------------------------------------- 6
TOOLS ------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING ---------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS -------------------------------------------------------- 8
MAINTENANCE -------------------------------------------------------------------------- 12
TROUBLESHOOTING ------------------------------------------------------------------ 12
WARM UPAND COOL DOWN ROUTINE ----------------------------------------- 13
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing, free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the load, turn the tension control knob in a clockwise direction.
To decrease the load, turn the tension control knob in a counterclockwise direction.
Adjusting the Rear Stabilizer End Cap
Turn the rear stabilizer end cap on the rear stabilizer as needed to level the bike.
Adjusting the Seat Height
Turn the seat post knob in a counterclockwise direction until the seat post can be slid up or
down and then slide the seat post up or down direction to the suitable position. Lock the
seat post in place by tightening the seat post knob in a clockwise direction.
NOTE: When adjusting the height of seat post, the maximum insert depth mark line
cannot higher than the edge of seat post bushing.
OPERATING THE COMPUTER
SPECIFICATIONS:
TIME---------------------------------------------------- 0:00-99:59 MIN: SEC
SPEED------------------------------------------------- 0.0-999.9 KM/H
DIST (DISTANCE)-----------------------------------0.0-999.9 KM
CAL (CALORIES)------------------------------------0.0-999.9 KCAL
ODO (ODOMETER)---------------------------------0-9999 KM
PULSE--------------------------------------------------40-240 BEATS/MIN
BUTTON FUNCTIONS:
MODE: Press MODE button to select each function of computer.
Press and hold MODE button for 3 seconds, all data values will clear to zero except the
ODO (ODOMETER) data values.
COMPUTER FUNTIONS:
AUTO ON/OFF: When you start to exercise or press the MODE button on the computer, the
computer will turn on. If you leave the equipment for 256 seconds, the power will turn off
automatically.
SCAN: Press MODE button until the arrow points to the SCAN; the computer will
automatically scan the function of TIME, SPEED, DIST (DISTANCE), CAL (CALORIES),
ODO (ODOMETER), and PULSE every 6 seconds.
TIME: Press MODE button until the arrow points to the TIME; the computer will display your
elapsed workout time in minutes and seconds.

4
SPEED: Press MODE button until the arrow points to the SPEED; the computer will display
the current training speed.
DIST (DISTANCE): Press MODE button until the arrow points to the DIST; the computer will
display the accumulative distance traveled during workout.
CAL (CALORIES): Press MODE button until the arrow points to the CAL; the computer will
display the total accumulated calories burned during workout. (This data is a rough guide
for comparison of different exercise sessions and should not be used in medical treatment).
ODO (ODOMETER): Press MODE button until the arrow points to the ODO; the computer
will display the total accumulative distance traveled. The data values of ODO can not be
clear to zero by pressing and holding MODE button for 3 seconds. If you take out the
batteries from the computer, the ODO data values will clear to zero.
PULSE: Press MODE button until the arrow points to the PULSE; the computer will display
your current heart rate figures after you hold both two hands on handlebar grip sensors. To
ensure the pulse readout is more precise, please always hold on to the handlebar grip
sensors with two hands instead of just with one hand only when you try to test your heart
rate figures.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover at the rear of computer.
2. Place two "SIZE-AA" batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are proper contact with
batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial segment appear, remove batteries and wait 15
seconds before reinstalling.

5
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 1 030 Adjustable Bolt 2
002 Handlebar Ø25x1.5 1 031 U Bracket 2
003 Handlebar Post 70x30x1.5 1 032 Spring Washer Ø6 2
004 Rear Stabilizer Ø50x1.5x430 1 033 Hex Nut M6 2
005 Flywheel Ø230 1 034 Cap Nut M10 4
006 Front Stabilizer Ø50x1.5x380 1 035 Carriage Bolt M10x57 4
007 Tension Control Knob 1 036 Curve Washer Ø10 4
008 Seat Post Knob M16x1.5 1 037 Front Stabilizer Support 1
009 Belt PJ 380J6 1 038 Washer Ø8 12
010 Computer JVT29120 1 039 Curve Washer Ø16xØ8 2
011 Nut M10x1 2 040 Pan Head Phillips Self Tapping
Screw ST4.2x25 6
012 Seat Post Bushing 1 041 Spring 1
013 Left Cover 1 042 Locknut M8 2
014 Right Cover 1 043 Bolt M8x18 1
015 Screw ST2.9x12 2 044 Idle Wheel Bracket 1
016 Ring 1 045 Idle Wheel 1
017 Axle Sleeve 15/16” 1 046 Seat Post Cover 1
018 Nut 7/8" 2 047 Handlebar Post Cover 1
019 Belt Pulley with Crank 240J6 1 048 Bolt M5x20 1
020 Left Foot Pedal YH-30X 1 049 Axle Sleeve 7/8” 1
021 Right Foot Pedal YH-30X 1 050 Handlebar Foam Grip
Ø30xØ24x455 2
022 Axle Bush 2 051 Screw ST4.2x20 2
023 Ball Bearing 2 052 Transport Wheel Ø23xØ6x32 2
024 Bolt M8x15 7 053 Hand Pulse Sensor with Wire
L=750mm 2
025 Seat Post 60x20x1.5 1 054 Big Washer Ø5 1
026 Sensor with Wire L=750mm 1 055 Nylon Nut M6 2
027 Seat Cushion DD-982AT 1 056 Bolt M6x48 1
028 Front Stabilizer End Cap Ø50x1.5 2 057 Curve Washer Ø20xØ8 1
029 Rear Stabilizer End Cap Ø50x1.5 2 058 Tension Cable L=1150mm 1

6
PARTS LIST
No. Description Qty No. Description Qty
059 Middle Section Sensor Wire
L=900mm 1 063 Washer 7/8" 1
060 Adjustable Handlebar End Cap
Ø25 2 064 Bolt M5x10 4
061 Bolt M8x30 2 065 Cover Cap 2
062 Bolt M8x10 4
HARDWARE PACKING LIST
TOOLS
(34) Cap Nut M10
4 PCS (35) Carriage Bolt M10x57 4 PCS (36) Curve Washer Ø10 4 PCS
Allen Wrench 6mm
1 PC Multi Hex Tool with Phillips Screwdriver S13, S14, S15
1 PC
Multi Hex Tool
1 PC

7
OVERVIEW DRAWING
16
18
17 23 22
29
23 49
919
10
58
54
48
59
27
3
25
46
47
8
28
28
6
4
13
14
42 38
1
2
5
11
7
12
15
20
21
26
30
30
35
35
34
36
45
44
43
37
38
38
38
40
40
41
50
51
52 52
55
56
56
60
24
24
61
62
63
64
65
65
39
11
29
31 32 33
22
57
24 38 62
38
34
36
50
53
24

8
ASSEMBLY INSTRUCTIONS
1. Front Stabilizer Support Installation
Remove six Ø8 Washers (38), four M8x15 Bolts
(24), and two M8x30 Bolts (61) from the Front
Stabilizer Support (37).
Insert the Front Stabilizer Support (37) into the
tube of Main Frame (1) and align bolt holes.
Secure the Front Stabilizer Support (37) with six
Ø8 Washers (38), four M8x15 Bolts (24), and
two M8x30 Bolts (61) that were removed.
Tighten bolts with the Allen Wrench provided.
Tool:
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
2. Front and Rear Stabilizers Installation
Position the Front Stabilizer (6) in front of
Front Stabilizer Support (37) and align bolt
holes.
Attach the Front Stabilizer (6) onto the front
curve of the Front Stabilizer Support (37) with
two M10 Cap Nuts (34), two M10x57
Carriage Bolts (35), and two Ø10 Curve
Washers (36). Tighten bolts with the Multi
Hex Tool provided.
Position the Rear Stabilizer (4) behind the
Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (4) onto the rear
curve of the Main Frame (1) with two M10
Cap Nuts (34), two M10x57 Carriage Bolts
(35), and two Ø10 Curve Washers (36).
Tighten bolts with the Multi Hex Tool
provided.
Hardware:
4 Cap Nuts (M10) 4 Carriage Bolts (M10x57) 4 Curve Washers (Ø10)
Allen Wrench 6mm
37
1
38
24 61
24
38
38
Tool:
Multi Hex Tool
34
36
35
6
35
36
34
37
1
4

9
3. Foot Pedal Installation
The Cranks, Pedal Shafts, Pedal Straps, and
Foot Pedal are marked “R” for Right and “L”
for Left.
Insert the pedal shaft of Left Foot Pedal (21)
into threaded hole in the left Crank (19).
Turn the pedal shaft by hand in the
counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the
clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (21)
with the Multi Hex Tool with Phillips Screwdriver
provided.
Insert pedal shaft of Right Foot Pedal (20) into
threaded hole in right Crank (19).
Turn the pedal shaft by hand in the clockwise
direction until snug.
Tighten pedal shaft of Right Foot Pedal (20)
with the Multi Hex Tool with Phillips Screwdriver
provided.
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
4. Seat Cushion and Seat Post Installation
Release both nut just a little bit from underneath of the
Seat Cushion (27) and then attach the Seat Cushion (27)
onto the top end of the Seat Post (25) with nuts. Tighten
both nuts after adjustment.
Slide the Seat Post Cover (46) onto the Main Frame (1).
Insert the Seat Post (25) into the Seat Post Bushing (12).
Adjust the seat position and insert the M16x1.5 Seat Post
Knob (8). Turn the M16x1.5 Seat Post Knob (8) in the
clockwise direction to tighten.
Tool:
Multi Hex Tool with Phillips
Screwdriver S13, S14, S15
21
20
19
Tool:
Multi Hex Tool with Phillips
Screwdriver S13, S14, S15
8
46
25
27
12
1

10
5. Handlebar Post and Tension Control Knob Installation
Slide the Handlebar Post Cover (47) onto the Main Frame (1).
Remove one M8x15 Bolt (24), one Ø20xØ8 Curve Washer (57), four Ø8 Washers (38), and
four M8x10 Bolts (62) from the Main Frame (1).
Insert the Tension Cable (58) through into the bottom hole of Handlebar Post (3) and pull it
out from the square hole of Handlebar Post (3).
Connect the Sensor Wire (26) from the Main Frame (1) to the Middle Section Sensor Wire
(59) from the Handlebar Post (3).
Insert the Handlebar Post (3) onto the tube of the Main Frame (1) and secure with one
M8x15 Bolt (24), one Ø20xØ8 Curve Washer (57), four Ø8 Washers (38), and four M8x10
Bolts (62) that were removed.
Remove the M5x20 Bolt (48) and Ø5 Big Washer (54) from the Tension Control Knob (7).
Put the cable end of resistance cable of Tension Control Knob (7) into the spring hook of
Tension Cable (58) as shown in drawing A of figure 5. Pull the resistance cable of Tension
Control Knob (7) up and force it into the gap of metal bracket of Tension Cable (58) as shown
in drawing B of figure 5. Attach the Tension Control Knob (7) onto the Handlebar Post (3)
with the M5x25 Bolt (48) and Ø5 Big Washer (54) that were removed.
Multi Hex Tool with Phillips
Screwdriver S13, S14, S15
Allen Wrench 6mm
Tool:
58
7
59
54
48
3
1
62
38
38
62
26
59
47
58
24 57
A B
7
7
58
58

11
6. Handlebar and Computer Installation
Remove two M8x15 Bolts (24) and two Ø16xØ8 Curve Washers (39) from the Handlebar
Post (3).
Insert the Hand Pulse Sensor Wires (53) into the hole on the Handlebar Post (3) and then
pull them out from the top end of the Handlebar Post (3).
Attach the Handlebar (2) onto the Handlebar Post (3) with two M8x15 Bolts (24) and two
Ø16xØ8 Curve Washers (39) that were removed. Tighten bolts with the Allen Wrench
provided.
Remove four M5x10 Bolts (64) from the Computer (10). Connect the Hand Pulse Sensor
Wires (53) and Middle Section Sensor Wire (59) to the wires that come from the Computer
(10). Tuck wires into the Handlebar Post (3).
Attach the Computer (10) onto the top end of the Handlebar Post (3) with four M5x10 Bolts
(64) that were removed. Tighten bolts with the Multi Hex Tool with Phillips Screwdriver
provided.
Multi Hex Tool with Phillips
Screwdriver S13, S14, S15
Allen Wrench 6mm
Tool:
59
10
64
2
3
53
39
24

12
MAINTENANCE
Cleaning
The upright bike can be cleaned with a soft cloth and mild detergent. Do not use abrasives
or solvents on plastic parts. Please wipe your perspiration off the bike after each use. Be
careful not get excessive moisture on the computer display panel as this might cause an
electrical hazard or electronics to fail.
Please keep the upright bike, specially, the computer console, out of direct sunlight to
prevent screen damage.
Please inspect all assembly bolts and pedals on the machine for proper tightness every
week.
Storage
Store the upright bike in a clean and dry environment away from children.
TROUBLESHOOTING
PROBLEM: The upright bike wobbles when in use.
SOLUTION: Turn the rear stabilizer end cap on the rear stabilizer as needed to level the
bike.
PROBLEM: There is no display on the computer console.
SOLUTION: Remove the computer console and verify the wires that come from the
computer console is properly connected to the wires that come from the handlebar post and
adjustable handlebar.
SOLUTION: Check the batteries are correctly positioned and battery springs are proper
contact with batteries.
SOLUTION: The batteries in the computer console may be dead. Change the new
batteries.
PROBLEM: There is no heart rate reading or heart rate reading is erratic or inconsistent.
SOLUTION: Make sure that the wire connections for the hand pulse sensors are secure.
SOLUTION: To ensure the pulse readout is more precise, please always hold on to the
handlebar grip sensors with two hands instead of just with one hand only when you try to test
your heart rate figures.
SOLUTION: Gripping the hand pulse sensors too tight. Try to maintain moderate pressure
while holding onto the hand pulse sensors.
PROBLEM: The upright bike makes a squeaking noise when in use.
SOLUTION: The bolts may be loose on the upright bike, please inspect the bolts and tighten
the loose bolts.

13
WARM UP AND COOL DOWN ROUTINE
Agood exercise program consists of a warm-up, aerobic exercise, and a cool down. Do the
entire program at least two to three times a week, resting for a day between workouts. After
several months you can increase your workouts to four or five times per week.
AEROBIC EXERCISE is any sustained activity that sends oxygen to your muscles via your
heart and lungs. Aerobic exercise improves the fitness of your lungs and heart. Aerobic
fitness is promoted by any activity that uses your large muscles eg: legs, arms and buttocks.
Your heart beats quickly and you breathe deeply. An aerobic exercise should be part of
your entire exercise routine.
The WARM-UP is an important part of any workout. It should begin every session to
prepare your body for more strenuous exercise by heating up and stretching your muscles,
increasing your circulation and pulse rate, and delivering more oxygen to your muscles.
COOL DOWN at the end of your workout, repeat these exercises to reduce soreness in tired
muscles.
HEAD ROLLS
Rotate your head to the right for one count,
feeling the stretch up the left side of your neck,
then rotate your head back for one count,
stretching your chin to the ceiling and letting
your mouth open. Rotate your head to the left
for one count, then drop your head to your chest
for one count.
SHOULDER LIFTS
Lift your right shoulder toward your ear for one
count. Then lift your left shoulder up for one
count as you lower your right shoulder.

14
SIDE STRETCHES
Open your arms to the side and lift them until
they are over your head. Reach your right arm
as far toward the ceiling as you can for one
count. Repeat this action with your left arm.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach
behind you and pull your right foot up. Bring
your heel as close to your buttocks as possible.
Hold for 15 counts and repeat with left foot.
INNER THIGH STRETCH
Sit with the soles of your feet together and your
knees pointing outward. Pull your feet as close
to your groin as possible. Gently push your
knees toward the floor. Hold for 15 counts.

15
HAMSTRING STRETCHES
Extend your right leg. Rest the sole of
your left foot against your right inner
thigh. Stretch toward your toe as far as
possible. Hold for 15 counts. Relax
and then repeat with left leg.
CALF/ACHILLES STRETCH
Lean against a wall with your left leg in front of
the right and your arms forward. Keep your
right leg straight and the left foot on the floor;
then bend the left leg and lean forward by
moving your hips toward the wall. Hold, then
repeat on the other side for 15 counts.
TOE TOUCHES
Slowly bend forward from your waist, letting
your back and shoulders relax as you stretch
toward your toes. Reach as far as you can and
hold for 15 counts.