Lindab AGHR-100 User manual

USER’S MANUAL
• AGHR-100
• ASHR-100
• AGHR-130
• ASHR-130
• AGHR-150
• ASHR-150
SINGLE-ROOM
REVERSIBLE ENERGY
REGENERATION VENTILATOR

2
Safety requirements 3
Purpose 5
Delivery set 5
Main technical parameters 6
Design and operating logic 11
Mounting and set-up 13
Connection to power mains 20
Ventilator control 23
Maintenance 25
Troubleshooting 27
Storage and transportation regulations 27
Manufacturer's warranty 28
Acceptance certicate 29
Seller information 29
Installation certicate 29
Warranty Card 30
CONTENTS

3
• Read the user’s manual carefully prior to installing and operating the unit.
• Full the user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical and
technical norms and standards.
• The warnings contained in the user’s manual must be considered most seriously since they contain vital personal safety information.
• Failure to follow the rules and safety precautions noted in this user’s manual may result in an injury or unit damage.
• After a careful reading of the manual, keep it for the entire service life of the unit.
• While transferring the unit control the User’s manual must be turned over to the receiving operator.
Symbol legend:
WARNING!
DO NOT!
SAFETY REQUIREMENTS
The user’s manual consisting of the technical details, operating instructions and technical specication applies to the installation and
mounting of the single-room energy regeneration reversible ventilator (hereinafter «the unit» as mentioned in the «Safety Requirements» and
«Manufacturer’s Warranty» sections as well as in warnings and information blocks).
UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS
• Disconnect the unit from power mains prior
to any installation operations. • The unit must be grounded!
• Do not lay the power cable of the unit in
close proximity to heating equipment.
• While installing the unit follow the safety
regulations specic to the use of electric
tools.
• Do not change the power cable length at
your own discretion.
• Do not bend the power cable.
• Avoid damaging the power cable.
• Do not put any foreign objects on the power
cable.
• Unpack the unit with care.
• Do not use damaged equipment or cables
when connecting the unit to power mains.
• Do not operate the unit outside the
temperature range stated in the user’s
manual.
• Do not operate the unit in aggressive or
explosive environments.
• Do not touch the unit controls with wet
hands.
• Do not carry out the installation and
maintenance operations with wet hands.
• Do not wash the unit with water.
• Protect the electric parts of the unit against
ingress of water.

4
UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS
• Do not allow children to operate the unit. • Disconnect the unit from power mains prior to
any technical maintenance.
• Do not store any explosive or highly ammable
substances in close proximity to the unit.
• When the unit generates unusual sounds,
odour or emits smoke disconnect it from
power supply and contact the Seller.
• Do not open the unit during operation. • Do not direct the air ow produced by the unit
towards open ame or ignition sources.
• Do not block the air duct when the unit is
switched on.
• In case of continuous operation of the unit
periodically check the security of mounting.
• Do not sit on the unit and avoid placing
foreign objects on it. • Use the unit only for its intended purpose.

5
The unit is designed to ensure continuous mechanical air exchange in houses, oces, hotels, cafes, conference halls and other utility and
public spaces.
The ventilator is equipped with a ceramic regenerator that enables supply of fresh ltered air heated by means of extract air heat energy
regeneration.
The ventilator is designed for through-the-wall mounting.
The telescopic ventilator design enables its installation in the walls with various thickness, see the table below:
Wall thickness Ventilator model
300 mm - 570 mm (11 13/16’’ - 22 7/16”) • AGHR-100
• ASHR-100
250 mm - 470 mm (9 13/16’’ - 18 1/2”)
• AGHR-130
• ASHR-130
• AGHR-150
• ASHR-150
The ventilator is rated for continuous operation always connected to power mains.
Transported air must not contain any ammable or explosive mixtures, evaporation of chemicals, sticky substances, brous materials,
coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, pathogenic
germs).
Name Number
Ventilator 1 item
Fastening set 1 item
Remote control 1 item
User's manual 1 item
Packing box 1 item
PURPOSE
THE UNIT MAY NOT BE OPERATED BY CHILDREN OR PERSONSWITH REDUCED PHYSICAL, MENTAL OR SENSORY
CAPACITIES, OR LACKING THE APPROPRIATE TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED PERSONNEL AFTER THE
APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED ACCESS BY UNATTENDED
CHILDREN.
DELIVERY SET

6
The ventilator is designed for indoor application with the ambient temperature ranging from -20°C (-4 °F) up to +50°C (+122 °F) and relative
humidity up to 80%.
The ventilator is rated as a class I electric appliance.
Ingress Protection (IP) rating from solid objects and liquids IP 24.
The ventilator design is regularly improved, so some models may slightly dier from those ones described in this manual.
300-570
(11 ⁄"-22 ⁄")
133
(5 ¼")
50
(1 ⁄")
260
(10 ¼")
240
(
9 ⁄" )
205
( 8 ⁄")
107
4 ⁄"
103
4 ⁄"
107
4 ⁄"
103
4 ⁄"
300-570
(11 ⁄"-22 ⁄")
133
(5 ¼")
35
(1 ⁄")
260
(10 ¼")
240
(
9 ⁄" )
165
( 6 ½")
VENTILATOR OVERALL DIMENSIONS, MM INCHES
ASHR-100
MAIN TECHNICAL PARAMETERS
AGHR-100

7
120-300
(4 ¾"-11 ⁄")
57
(2 ¼")
144
(5 ⁄")
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
57
(2 ¼")
300 (11 ⁄")
300
(11 ⁄")
310 (12 ⁄")
260
(10 ¼")
280
(11")
213
( 8 ⁄")
213
( 8 ⁄")
132
5 ⁄"
128
5 ⁄"
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
3 1/8"
80
(3 ⁄")
300
(11 ⁄")
280
(11")
240
( 9 ⁄")
240
( 9 ⁄")
120-300
(4 ¾"-11 ⁄")
80
(3 ⁄")
144
(5 ⁄")
300 (11 ⁄")
310 (12 ⁄")
260
(10 ¼")
132
5 ⁄"
128
5 ⁄"
132
5 ⁄"
128
5 ⁄"
132
5 ⁄"
128
5 ⁄"
120-300
(4 ¾"-11 ⁄")
65
(2 ⁄")
144
(5 ⁄")
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
65
(2 ⁄")
300 (11 ⁄")
300
(11 ⁄")
310 (12 ⁄")
260
(10 ¼")
280
(11")
213
( 8 ⁄")
213
( 8 ⁄")
157
6 ⁄"
153
6"
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
86
(3 ⁄")
300
(11 ⁄")
280
(11")
240
( 9 ⁄")
157
6 ⁄"
153
6"
157
6 ⁄"
153
6"
120-300
(4 ¾"-11 ⁄")
86
(3 ⁄")
144
(5 ⁄")
300 (11 ⁄")
310 (12 ⁄")
260
(10 ¼")
157
6 ⁄"
153
6"
240
( 9 ⁄")
ASHR-130
ASHR-150
AGHR-130
120-300
(4 ¾"-11 ⁄")
65
(2 ⁄")
144
(5 ⁄")
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
65
(2 ⁄")
300 (11 ⁄")
300
(11 ⁄")
310 (12 ⁄")
260
(10 ¼")
280
(11")
213
( 8 ⁄")
213
( 8 ⁄")
157
6 ⁄"
153
6"
250-470
(9 ⁄"-18 ½")
133
(5 ¼")
86
(3 ⁄")
300
(11 ⁄")
280
(11")
240
( 9 ⁄")
157
6 ⁄"
153
6"
157
6 ⁄"
153
6"
120-300
(4 ¾"-11 ⁄")
86
(3 ⁄")
144
(5 ⁄")
300 (11 ⁄")
310 (12 ⁄")
260
(10 ¼")
157
6 ⁄"
153
6"
240
( 9 ⁄")
AGHR-150

8
VENTILATOR TECHNICAL DATA
AGHR-100, ASHR-100
Speed I II III
Supply Voltage, 50-60 Hz [V] 1~100-230
Air Capacity [m3/h] (CFM) 7 (4) 15 (9) 24 (14)
Power [W] 3,50 3,95 5,32
Current [A] 0,023 0,026 0,036
RPM [min-1] 1190 1330 2420
Noise Level, 1 m [dB(A)] (Sones) 31 (0,9) 35 (1,3) 43 (2,5)
Noise Level, 3 m [dB(A)] (Sones) 22 (0,4) 25 (0,5) 33 (1,1)
Outdoor noise attenuation [dB(A)] (Sones) 16 (0,4)
Heat Recovery Eciency up to 85%
AGHR-130, ASHR-130
Speed I II III
Supply Voltage, 50-60 Hz [V] 1~100-230
Air Capacity [m3/h] (CFM) 10 (6) 20 (12) 30 (18)
Power [W] 3,93 4,39 5,10
Current [A] 0,023 0,026 0,032
RPM [min-1] 745 1075 1670
Noise Level, 1 m [dB(A)] (Sones) 27 (0,6) 32 (1,0) 38 (2,0)
Noise Level, 3 m [dB(A)] (Sones) 18 (0,4) 23 (0,5) 28 (0,7)
Outdoor noise attenuation [dB(A)] (Sones) 17 (0,4)
Heat Recovery Eciency up to 90%
VENTILATOR TECHNICAL DATA
AGHR-150, ASHR-150
Speed I II III
Supply Voltage, 50-60 Hz [V] 1~100-230
Air Capacity [m3/h] (CFM) 14 (8) 28 (16) 54 (32)
Power [W] 3,80 3,96 5,61
Current [A] 0,024 0,026 0,039
RPM [min-1] 610 800 1450
Noise Level, 1 m [dB(A)] (Sones) 22 (0,4) 29 (0,7) 32 (1,0)
Noise Level, 3 m [dB(A)] (Sones) 13 (0,2) 20 (0,4) 23 (0,5)
Outdoor noise attenuation [dB(A)] (Sones) 18 (0,4)

9
The ventilator consists of the telescopic air duct with an adjustable length regulated by position of the inner air duct inside the outer air
duct, the ventilation unit and the ventilation hood.
Two lters and the ceramic regenerator are located in the inner duct of the telescope.
The lters are designed to purify supply air and prevent foreign object ingress to the regenerator and the fan.
The ceramic regenerator uses extract air heat energy to warm up supply air ow.
The regenerator is equipped with a pull cord inside to facilitate its withdrawal from the ventilator.
The regenerator is heat insulated with a specially designed insulating material.
The ventilation unit must be installed on inner side of the wall. The ventilation unit is equipped with automatic shutters that shut the air
duct o during the ventilator standby and prevent air back draft.
The ventilation hood must be installed on the outer wall side. It is used for directed air discharge and prevention of ingress of water and
other objects to the ventilator.
VENTILATOR DESIGN
Outer air duct
Outer part of the
telescopic air duct.
Inner air duct
Inner part of the tele-
scopic air duct.
Ventilation unit
Is used to generate air ow by means of
the fan. The decorative grille protects the
fan against ingress of foreign objects
from the premises. The ventilation unit is
equipped with automatic shutters open-
ing when the ventilator is on and clos-
ing when it is o, thus preventing back
air ow.
Outer ventilation hood
Prevents direct water and foreign objects
ingress to the ventilator.-
ASHR-100
AGHR-130
ASHR-130
AGHR-150
ASHR-150
Filter
Designed to clean supply air
ow and prevent dust and for-
eign objects ingress to the venti-
lator. The lters prevent regener-
ator soiling.
Ceramic regenerator
Provides extract air heat
energy regeneration to
warm up supply air ow.
Mounting plate
A mounting plate for installation
the ventilation unit on the wall
and connecting the ventilator to
power supply.
AGHR-100
что ставить
DESIGN AND OPERATING LOGIC

10
VENTILATOR OPERATING MODES
The ventilator has four ventilation modes:
• Natural air supply - the automatic shutters are opened, the fan does not run
• Supply - the ventilator supplies fresh air to the premise no matter of CN7 jumper position.
• Ventilation — the ventilator operates in permanent supply or extract mode at set speed depending on CN7 jumper position.
• Regeneration - the ventilator operates in reversible mode with heat and humidity regeneration.
A
I
R
E
X
T
R
A
C
T
A
I
R
S
U
P
P
L
Y
CYCLE I
CYCLE II
7
0
s
e
c
7
0
s
e
c
-10 °С
-10 °С
+20 °С
+20 °С
+17 °С
+17 °С
-7 °С
-7 °С
In Regeneration mode the ventilator operates in two cycles, 70 seconds each.
Cycle I. Warm stale air is extracted from the room. As it ows through the regenerator, it heats and moisturizes the regenerator, transferring
up to 90% heat energy. In 70 seconds as the ceramic regenerator gets warmed the ventilator is switched to supply mode.
Cycle II. Fresh intake air from outside ows through the ceramic regenerator and absorbs accumulated moisture and heat up to the room
temperature. In 70 seconds as the ceramic regenerator gets cooled down, the ventilator is switched into extract mode and the cycle is
renewed.