Lindab AGF Series User manual

EN
AXIAL FANS
USER’S MANUAL

EN
WARNING!
Disconnect the fan from power supply prior to any connection, servicing and repair operations.
Only duly qualified electricians with valid electrical permit for electric operations at the units with operating voltage up
to 1000 V are allowed for mounting and maintenance after careful study of the present user’s manual.
The single-phase power mains must comply with the acting localelectricalnorms and standards.
The fixed electricalwiring must be equipped with an automatic circuit breaker.
The fan must be connected to power mains through an automatic circuit breaker QF integrated into fixed wiring system with the
gap between the breaker contacts on allpoles not less than 3 mm.
Check the fan for any visible damages ofthe impeller and the casing before starting installation. The casing internals must be
free ofany foreign objects which can damage the impeller blades.
Due to constant improvements the design ofsome models may slightly differ from those ones described in this manual.
While mounting the fan avoid the casing compression!
Deformation ofthe casing may result in the motor jam and excessive noise.
Misuse ofthe fan and any unauthorised modifications are not allowed.
Take steps to prevent ingress ofsmoke, carbon monoxide and other combustion products into the room through open chimney
flues or other fire-protection devices. Sufficient air supply must be provided for proper combustion and exhaust ofgases through the
chimney offuelburning equipment to prevent back drafting.
Transported air must not contain any dust or other solid impurities, sticky substances or fibrous materials.
Do not use the fan in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc.
Do not close or block the fan intake or extract vents in order to ensure the efficient stream.
Do not sit on the fan and do not put objects on it.
The timer circuit is live.
Disconnect the fan from power supply prior to any adjustment operations.
The fan delivery set includes a specially designed plastic screwdriver for adjustment ofthe fan parameters.
Use the plastic screwdriver to change the fan turn-offdelay time.
The product is allowed to be used by children aged from 8 years and above and persons with reduced physical, sensory or
mentalcapabilities or lack ofexperience and knowledge provided that they have been given supervision or instruction regarding a safe
use ofthe product and understand the risks involved.
Do not allow children play with the product.
Fan cleaning and maintenance must only be performed by children under adult supervision.
RECYCLE AT THE END OF THE SERVICE LIFE.
DO NOT DISPOSE THE PRODUCT WITH UNSORTED MUNICIPAL TRASH.
2

EN
DESIGNATION KEY
100 AGF ХКХХ
Exhaust pipe diameter [mm]
Fan series
Extra options:
V: pull cord switch
T: turn-on delay timer
T1: turn-on and turn-off delay timer
TH: humidity sensor and turn-off delay timer
TP: motion sensor and turn-off delay timer
K: back valve
Motor and impeller modifications:
L: ball bearing motor
turbo: high-powered motor
Q: low-powered motor
12: motor compatible with 12V/50 Hz safe voltage
press: high-pressure motor
Power mains parameters
_ - 230 V/ 50-60 Hz by default
If the fan is compatible with other power supply parameters, these are indicated in the
fan model name.
DELIVERY SET
•
Fan - 1 item
•
Screws and dowels - 4 items
•
Plastic screwdriver (only for the models with a timer)
•
User’s manual
•
Packing box
3

EN
BRIEF DESCRIPTION
The products is an axial fan for exhaust ventilation of small to medium-sized premises.
The fan is made of white plastic.
This fan may be equipped with a back valve that prevents air back drafting at the fan standstill.
The fan is designed for connection to 100, 125 and 150 mm air ducts.
Due to constant improvements the design of some models may slightly differ from those ones described in
this manual.
OPERATION GUIDELINES
The fan is rated for connection to 220...240 V/ 50-60 Hz AC single-phase power supply source.
supply via a step-down transformer, for example, TRF 220/12-25 (not included in the delivery, available upon
separate order).
The fan is designed for continuous operation always connected to power mains.
Air flow direction in the system must match the pointer direction on the fan casing.
Ingress protection rating against access to hazardous parts and water ingress is IP 34.
The fan is rated for operation at the ambient temperature ranging from +1 °C up to +45 °C.
The fan requires no grounding.
4

EN
MOUNTING
READ THE USER’S MANUAL CAREFULLYBEFORE PROCEEDING WITH INSTALLATION WORKS.
COMPLIANCE WITH THE MANUAL REQUIREMENTS ENSURES RELIABLE OPERATIONAND LONG
SERVICE LIFE OF THE PRODUCT.
KEEPTHE USER’S MANUALAVAILABLEAS LONGASYOU USE THE PRODUCT. YOU MAY NEED TO
RE-READ THE INFORMATION ON THE PRODUCT SERVICING.
The fan is designed for vertical or horizontal installation and connection to a ventilation shaft or a round air duct
of a matching diameter, Fig. 1.
Fan mounting steps:
Step 1. Cut offpower supply and prepare a premise for installation of the fan, Fig. 2-3.
Step 2. Remove the front panel from the fan, Fig.4 .
Step 3. Mark and drill the holes for fasteners, insert the fasteners and fix the fan, Fig. 5-7.
Step 4. Connect the fan to power supply and adjust the timer and humidity set points if required, Fig. 8-14.
Step 5. Cover the fan with a front panel, Fig. 15.
Step 6. Connect the fan to power supply, Fig. 16.
TERMINAL DESIGNATION KEY
L
live wire (applicable for 220-240 V/ 50-
60 Hz)
ATTENTION! THE FAN RATED FOR 12V
N
neutral wire (applicable for 220-240 V/
POWER SUPPLY (MARKED ON THE FAN
50-60 Hz)
CASING) MUST BE CONNECTED TO 12 V
POWER SUPPLY SOURCE ONLY!
~
12 V/50 Hz power supply
LT (ST)
timer control circuit
QF
automatic circuit breaker
S
external on/off switch
5

EN
FAN OPTIONS
V - The fan is turned on and off with an integrated pull cord switch.
T - The fan is turned on with an external switch, for example, a light switch. After the fan is turned off with a switch, for
example, a light switch, the fan keeps operating for a set turn-off delay time, adjustable from 2 to 30 minutes.
T1 - After the fan is turned on with an external switch, for example, a light switch, the fan activates in a set turn-on delay
time, adjustable from 10 to 90 seconds. After the fan is turned off the fan keeps operating for a set turn-off delay time
period, adjustable from 2 to 30 minutes. The turn-on and turn-off delay time are set by means of the jumper on the control
circuit board.
TH - The fan is turned on with an external switch, for example, a light switch or it is activated by the humidity sensor as the
indoor humidity exceeds set level, adjustable from 60% up to 90%. After the fan is turned manually off with a light switch
or after the humidity level drops down below the set point the fan keeps operating for a set turn-off delay time period,
adjustable from 2 to 30 minutes.
To adjust the humidity set point turn the control knob H clockwise to increase and counter-clockwise to decrease the
humidity sensor set point, Fig. 13. To set the maximum humidity setpoint 90% set the potentiometer to Hmax position.
TP - The fan is turned on in case of activation of the motion sensor.
The motion sensor has a reach distance 1-4 m and horizontal viewing angle up to 100°. After no motion more is detected
the fan keeps operating for a set turn-off delay time period, adjustable from 2 to 30 minutes.
To adjust the fan turn-on delay time, turn the control knob Tz clockwise to increase and counter-clockwise to decrease the
turn-on delay time respectively, Fig. 12.
To adjust the fan turn-off delay time, turn the control knob T clockwise to increase and counter-clockwise to decrease the
turn-off delay time respectively, Fig. 12-13.
Warning! The timer circuit is live! Disconnect the fan from power supply prior to any adjustment operations. The fan de-
livery set includes a specially designed plastic screwdriver for fan settings adjustments. Use it to change the turn-on and
turn-off delay time and the humidity set point.
Do not use a metalscrewdriver, knife, etc. for adjustment operations not to damage the control circuit board.
6

EN
MAINTENANCE
The fan maintenance periodicity is at least once per 6 months.
Maintenance steps:
• Disconnect the fan from power supply. Fig. 17.
• Remove the front panel, Fig. 18.
• Wipe the fan with a dry cloth or a brush wetted in a mild detergent solution.
• Flush the front panel and rinse it with running water, Fig. 19-21.
• Wipe the fan surfaces dry.
• Cover the fan with the front panel, Fig. 22.
• Connect power supply to the fan, Fig. 16.
WARNING! Avoid water dripping on the electric components.
TRANSPORTATION AND STORAGE RULES
Store the product in the manufacturer’s original packing box in a dry ventilated premise at ambient temperatures from
+5°C up to + 40°C. Storage environment must not contain aggressive vapours and chemical mixtures provoking corrosion,
insulation and sealing deformation.
The unit can be carried in the original packing by any mode of transport provided proper protection against precipitation
and mechanical damage.
Avoid sharp blows, scratches or rough handling during loading and unloading.
MANUFACTURER’S WARRANTY
«We hereby declare that the product complies with the essentialprotection requirements ofElectromagnetic
CouncilDirective 2004/108/EC, 89/336/EEC and Low Voltage Directive 2006/95/EC, 73/23/EEC and CE-marking
Directive 93/68/EEConthe approximationofthe laws ofthe MemberStates relating toelectromagnetic compatibility.
This certificate is issued following test carried out on samples of the product referred to above.»
The manufacturer sets forth the warranty period of the fan within 60 months after the sale via retail network
subject to the customer’s ensuring compliance with the transportation, storage, mounting and operation rules.
In case of any malfunction of the fan through the manufacturer’s fault within the warranty period the
7

EN
customer is entitled to free elimination of the defects by means of warranty repair.
The warranty repair means performing works specific to elimination of faults in the fan operation to ensure its
intended use by the user within the warranty period.
The defects are eliminated by means of replacement or repair of the complete fan or a faulty part thereof.
The warranty repair does not include:
• Routine maintenance;
• Fan installation / dismantling;
• Fan setup.
To benefit from warranty repair the user must provide the fan, the user’s manual with stamped sale date and
the payment document to confirm the purchase.
The fan model must comply with the one stated in the user’s manual.
Contact the product seller for warranty service, repair or replacement.
The manufacturer’s warranty does not apply to the following cases:
• user’s failure to provide the fan in the entire delivery package as stated in the user’s manual, including
missing component parts previously dismounted by the user;
• mismatch of the fan model and make with the respective details stated on the fan packing and in the user’s
manual;
• user’s failure to ensure timely technical maintenance of the fan;
• external damage to the casing (excluding external modifications of the fan as required for its installation) and
the internal components of the fan;
• alteration of the fan design or engineering changes of the fan;
• replacement and use of the assemblies, parts and components not approved by the manufacturer;
• not intended use of the fan;
• user’s violation of the fan control regulations;
• fan connection to power pains with a voltage other than the one stated in the user’s manual or on the sticker
on the fan casing;
• fan breakdown due to voltage surges in the power mains;
• user’s discretionary repair of the fan;
• repair performed by any persons without the manufacturer’s authorization;
• expiry of the warranty period;
• user’s violation of the established regulations specific to the fan transportation;
• user’s violation of the fan storage regulations;
• wrongful acts against the fan committed by third persons;
• fan breakdown due to circumstances ofinsuperable force (fire, flood, earthquake, war, hostilities ofany kind,
8

EN
blockade, etc.);
• missing seals if provided by the user’s manual;
• failure to submit the user’s manual with the sale date stamp;
• failure to submit the warranty card;
• failure to submit a payment document certifying the fan purchase. .
FOLLOWING THE REGULATIONS STIPULATED HEREIN WILL ENSUREALONGAND
TROUBLE-FREE OPERATION OF THE FAN.
USERS’CLAIMS SHALL BE SUBJECT TO REVIEW ONLY UPON SUBMISSION OF THE
FAN, THE PAYMENT DOCUMENT AND THE USER’S MANUAL WITH THE SALES DATE
STAMP.
9

EN
1
10

EN
L N
QF
2
3
4
5
6
7
11

EN
QF
N
N
M
L
L
- / V/ TP
8
QF
N
N
LT
M
L
L
VT/VTH
9
QF
N
N
S
LT
M
L
L
T / T1 / TH
10
12

НТ
30 min
EN
ATTENTION!
*— The fan rated for 12 Vpower supply (marked
Т
on the fan casing) must be connected to 12 V
power supply source only!
2 min
30 min
Н
60%
90%
11
12
Тz
Jumper
10 sec
2 min
90 sec
30 min
Т
2 min
13
14
15
16
13

EN
L N
QF
17
18
19
20
21
22
14

EN
Approval mark
Sold
(name and stamp of the seller)
Manufacturing date
Sales date
15

ACCEPTANCE CERTIFICATE
V
turbo
100
T
press
125
AGF
T1
K
12
150
TH
Б
TP
Л
The fan is recognized as serviceable.
F01(М2)EN-01