Ltech LT-995 User manual

www.ltech-led.com
Short circuit / Over current / Overheat protection
8 bit / 16 bit
3 kinds of DMX interfaces
CHANNELS
LT-995
Photoelectric
isolation
006

Short circuit
protection
Overheat
protection
Over current
protection
4. With RDM remote management protocol, the operations can be completed
via the RDM master console, such as parameters browsing & settings, DMX
address settings, equipment recognition, etc.
2. Easy operation with digital display and the touch buttons.
1. Designed with 5 channels output, and Max. 6A current per channel, up to
720W output power.
6. With short circuit / overheat / over current protection, as well as warning
function when a fault occurs.
9. 16bit (65536 levels) / 8bit (256 levels) grey level available.
3. 3-pin XLR, RJ45 DMX and green terminal interface with photoelectric
isolation, improve signal transmission efficiency and anti-interference
ability, the green terminal also has signal amplifier function.
Product Introduction
www.ltech-led.com
1
3-pin XLR RJ45 RDM
7. With fast self-testing function.
5. With firmware upgrade function.
8. High/low PWM frequency available.
Photoelectric
isolation

TechnicalSpecs
www.ltech-led.com
2
LT-995
DMX512/RDM
12~24Vdc
6A × 5CH Max. 30A
(0~72W...144W) × 5CH Max. 720W
3-pin XLR, RJ45, green terminal
8bit (256 levels) / 16bit (65536 levels)
Yes
Short circuit / Overheat / Over current
protection, recover automatically.
-30°C~65°C
169×80×39mm(L×W×H)
182×91×41mm(L×W×H)
550g
Model:
Input Signal:
Input Voltage:
: Current Load
Output Power:
DMX Interfaces:
Grey Level:
Photoelectric Isolation:
Protection:
Working Temperature:
Dimensions:
Package Size:
Weight (G.W.):
5-Year
Warranty
E500585

0 0 6
39
3
169
157
80
59
www.ltech-led.com
Product Size
Main Component Descripition:
Unit: mm
RJ45
3-pin XLR
Green terminal
DMX/RDM
input & output
Digital
display
Dip
switch
Green terminal
LED lamp connection
12-24Vdc
Power input
Digital display Dip switch
High Smooth
Low Std
PWM Hz DIM
16
Bit
8
M
<
<
Digital display will enter the locked
mode without operating after 15S.
Long press “M” key to unlock.
Short press “M” key to switch numbers.
Press “ ””v” key to adjust value.
^
006
Screen
30S off
Enable

4
1
3
2
PUSH
1
3
2
PUSH
GND
DATA+
DATA-
12-24Vdc 12-24Vdc 12-24Vdc
LT-995 LT-995 LT-995
www.ltech-led.com
Wiring Diagram
LT-995 is equipped with 3 kinds of DMX terminals for
users’ selection. The following diagram takes 3-pin
XLR as an example, same connecting method for the
rest two: RJ45 & green terminal (with amplifier
function).
1. DMX console onnectionc :
DMX
console
DMX signal
DMX signal DMX signal
Resistor
terminal
If the recoil effect occurs because of longer signal line or bad line quality,
please try to connect 0.25W 90-120Ω terminal resistor at the end of each line.

LT-995
5
RGBWY LEDs
RGBWY LEDs
2 Connecting LED lights:
DMX/RDM Signal DMX/RDM Signal
12-24Vdc
LED driver
V+
V+
1
2
3
4
5
www.ltech-led.com

LT-995 LT-995 LT-995
6
LT-995 LT-995 LT-995
LT-995
LT-995
LT-995 LT-995
LT-995 LT-995 LT-995
These 3 terminals can be connected in a mixed way.
Resistor
terminal
Resistor
terminal
Resistor
terminal
Terminal
Resistor
4. The connection diagram of AMP signal amplifier terminal:
3. The connection diagram of 3 kindsofDMX/RDM terminals:
Connecting with green terminal or an extra amplifier will be needed when more than 32
decoders are connected or use overlong signal wire (as shown below).
Signal amplifier should not be more than 5 times continuously.
AMP
LT-995
LT-995
www.ltech-led.com
3-pin XLR
connected
in parallel
RJ45
connected
in parallel
Green terminal
connected
in parallel

www.ltech-led.com
7
LT-995
LT-995 LT-995
Work with RDM Editor
LT-995 can work with LTECH RDM editor (Model: WiFi-RDM01) to realize changing
the parameters by long-range setting, wiring diagram as below:
5-24Vdc
Power
input
WiFi-RDM01

www.ltech-led.com
8
RDM Editor App Interface Instructions
Download the App, setting LT-995 parameters (dimming range, brightness, boot
fade time etc.) after well connecting the RDM editor, more details, please check
the manual of WiFi-RDM01.
Well installation of products first, then working with WiFi -RDM01 to realize setting
parameters and firmware upgrade by App.
a: Click”Add”, edit the address in corresponding box.
b: Click”ID”, get more product details.
c: Click” ”, enter edited interface.
d: Click”No.”, issue the recognizing command.
WiFi-RDM01
upgrade
DMX device
upgrade
ac
b
d
Supporting WiFi-RDM01
upgrade and DMX driver
upgrade.

Update Time: 06/01/2021_A2
9
Attentions
Warranty agreement
Warranty exclusions below:
No any contract signed by LTECH.
Warranty labels and barcodes have been damaged.
Damage caused by natural disasters and force majeure.
Products with severe physical damage.
Beyond warranty periods.
Warranty periods from the date of delivery : 5 years.
Free repair or replacement services for quality problems are provided within warranty periods.
Any artificial damage caused by high voltage, overload, or improper operations.
1. Repair or replacement provided is the only remedy for customers. LTECH is not liable for
any incidental or consequential damage unless it is within the law.
2. LTECH has the right to amend or adjust the terms of this warranty, and release in written
form shall prevail.
This manual is subject to changes without further notice. Product functions depend on the goods.
Please feel free to contact our official distributors if you have any question.
Products shall be installed by qualified professionals.
LTECH products are non-waterproof (special models excepted). Please avoid the sun and
rain. When installed outdoors, please ensure it is mounted in a water proof enclosure.
Good heat dissipation will extend the working life of products. Please ensure good ventilation.
Please check if the working voltage used complies with the parameter requirements of products.
The diameter of wire used must be able to load the light fixtures you connect and ensure the
firm wiring.
Before you power on products, please make sure all the wiring is correct in case of incorrect
connection that causes damage to light fixtures.
If a fault occurs, please do not attempt to fix products by yourself. If you have any question,
please contact your suppliers.
www.ltech-led.com