luminii Level User manual

mounting
bracket canopy
#8-32 screw
wood screw
Page 1 of 2
Level - Installation Instructions
REV1.1
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. All 120VAC wires must be present in junction box.
4. More than one person is recommended for this installation.
1.1 Lay the fixture next to the wall. Use a level to align & center the
fixture to the junction box. Make any necessary markings to
install the canopy & mounting bracket to the drywall.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
2
2.1 Align and then tap each anchor onto the marks until the
threaded section. Followed by tightening the anchors with a
Phillips screw driver.
level
fixture
junction box
markings
1.1
wall
wall
2.1
anchor
wall
mark
1
mounting
bracket
junction box
markings
anchors
3.1 While holding the mounting bracket slide the canopy through
the driver wires.
3.2 Connect the white (neutral) & black (hot) driver wires to the
white & black power wires (120VAC).
3.3 Connect the ground wire in accordance with local electrical
codes.
canopy
3.2
wall
3
mounting
bracket
junction
box
3.1
3.2
4.1 Insert the wire nut connections into the junction box. Align the
canopy/mounting bracket to the junction box holes & anchors
and secure by using the provided screws.
Note: Use the provided universal crossbar if canopy does not align
to the junction box holes
4
mounting
bracket
55.1 Pull out the terminals from the inside of the mounting bracket.
5.2 Connect each pair of terminal blocks(24VDC) to the nearest set
of fixture red & black wires. Repeat for the remaining terminal
blocks.
5.3 Insert the terminal block connections back into the mounting
bracket to avoid any interference.
terminal
fixture
wires
5.1
5.2
fixture
Note: There are two anchor holes for the 78" version 76" spaced
apart, and two for the 48" version spaced 46" apart.
canopy
4.1
- Conforms to UL STD 1598
- Certied to CAN/CSA STD C22.2
No. 250.0-08
4002302 7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com

Page 2 of 2
Level - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. All 120VAC wires must be present in junction box.
4. More than one person is recommended for this installation.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
wall
6.1 Insert the fixture lower flange into the mounting bracket lip. Then push the fixture threaded slot to the mounting bracket holes and secure using the
provided self tapping screws, refer to diagram above for reference.
A B C D
fixture
mounting
bracket
lower
flange bracket lip
threaded
slot
mounting
bracket hole self tapping
screw
6
CERTAIN PARTS NOT SHOWN FOR CLARITY
7.1 From the top & bottom of the fixture, remove the protective film
from both of the diffuser lens.
7
fixture mounting
bracket
7.1
film 7.1
lens
- Conforms to UL STD 1598
- Certied to CAN/CSA STD C22.2
No. 250.0-08
4002302
REV1.1
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com