luminii Optic Arts CH-MD-LS-SF Series User manual

4”
every 30”
fixture
surface
CH-MD-LS-SF & CH-MD-TL-SF Channel - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 1 of 2
1.1 Snap the lens into the channel, then align & center the channel to the
determined location. Then make any reference marks if needed to install
the channel, reference step 3 for mounting options.
Note: Prior to install, 24VDC power must be present for wiring. Also
review and account for all parts necessary to install properly.
REV0.0 03092020
Caution: Safety equipment is recommended, when modifications are being
made to the channel & lens.
2.1 Extrusion & lens can be cut in the field. Using the proper blade for
aluminum, cut to the desired length.
channel
1.1
miter saw
Models CH-MD-LS-SF-XX & CH-MD-TL-SF
channel
STEP A STEP B STEP C
tighten screws below
channel surface
before installing LineLED
drill through
channel for
mounting
holes
countersink
the holes
3.1 Secure the channel to the surface by either mounting directly with screws or using mounting brackets.
Make counter sunk holes through the channel followed by screwing directly to the surface.a. If mounting channel with screws:
b. If mounting channel with brackets : fixed mounting brackets For , install a bracket 4” from each end, followed by installing one every 30”. Then secure, by
screwing through the bracket to the surface. For , install a bracket 4” from each end, followed by installing one every 30”. adjustable mounting brackets
Secure in place by screwing through the bracket to the surface. If necessary loosen the screw on the side & rotate to the desired position, followed by
tightening the screws.
channel
4.0” 30.0”
30.0” 4.0”
MOUNT CHANNEL
WITH SCREWS
install #4 flat head wood
screws a maximum 30"
apart minimum of 2
screws per channel.
a
mounting
bracket
1
4”
adjustable mounting
bracket
2lens
channel
2.1
2.1
3
fixed mounting
bracket
adjustable
mounting bracket
MOUNT EXTRUSION WITH FIXED OR
ADJUSTABLE BRACKETS
b
b

Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
7.1 Remove the protective film from the diffuser lens.
7.2 Align the edge of the lens to the inside of the channel. Followed by
carefully pushing and snapping into the other side little by little until its
completely installed.
5
5.1 Extrusion are not waterproof. If it is going to be installed Optional:
facing up and in a wet location, drainage holes should be drilled
along the inner corner of the channel every 12". Drill 1/16" to 1/8"
diameters holes before installing LED strip.
12.00"
corner drainage hole
corner
drainage
hole
5.1
4.1 F.OT. Flex or LineLED can be shortened by cutting along the dashed lines
in between the solder pads. Make sure the cut is made on the side of the
F.OT. Flex or LineLED without the wire leads. F.OT. Flex or LineLED cannot
touch the metal endcap which will shorten the circuit.
wire leads
4
3.1
channel
9.1 Ensure the correct (wattage & voltage) power supply is used to power
LineLED. Then proceed to connect LineLED wires from channel to power
supply. For more information please refer to power supply and LineLED
wiring instructions.
9
line voltage wires low voltage wires
class II power
supply
LineLED of
channel
9.1
8.1 add silicone to the endcaps & If channel is going to be installed outside,
the full length of the lens. To help avoid getting water inside the channel,
but will not make waterproof.
endcap
silicone
dispenser
Note: Reference step 8 first if installing outdoors. Then return
back to this step to install lens properly.
lens
7.1
7
7.2
channel
protective
film
lens
CH-MD-LS-SF & CH-MD-TL-SF Channel - Installation Instructions
Models CH-MD-LS-SF-XX & CH-MD-TL-SF
Page 2 of 2
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV0.0 03092020
solder pads
F.O.T. FLEX
cut
4.1
6
6.1 Prior to installing LineLED to channel, clean channel from any debris.
Gently push LineLED onto aluminum channel and then install endcaps at
both ends.
feed wire leads F.OT. Flex or LineLED
through the endcap opening
remove paper backing on the
adhesive tape of the LineLED
before installing to the channel
6.1
endcap
8
9.1
9.1
9.1
silicone
dispenser