luminii QUE Channel User manual

6
6.1
6.1 Prior to installing LineLED to extrusion, clean extrusion from any debris.
Gently push LineLED onto aluminum extrusion.
remove paper backing from the
adhesive tape of the LineLED
before installing the extrusion
extrusion
LED
1
QUE Channel - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 1 of 2
1.1 Snap lens into the extrusion, then align & center the extrusion to the
determined location. Make all necessary markings to install to the surface.
extrusion measure & then mark
reference points
Note: Complete fixture must be built prior to installing, to properly make all
necessary reference marks & to ensure all parts are included. Then it can be
taken apart for installation.
lens
measure
reference mark
1.1
REV0.1
aluminum
extrusion
Caution: Safety equipment is recommended, when modifications are being
made to the extrusion & lens.
2.1 If necessary extrusion with the lens installed can be cut in the field.
Use the proper blade for aluminum, and then cut to the desired length.
extrusion
with lens
2
miter saw
2.1
extrusion
4.1 Ensure appropriate drill bit is used
to drill in the aluminum extrusion.
Drill location for mounting holes every
30” or at least 2 screws per extrusion
from within the center groove of the
extrusion. Drill another hole to either the
extrusion or endcap for LineLED wires to
feed through to power supply.
solder pads
3.1 LineLED can be shortened by cutting along the dashed lines in between
the solder pads. Make sure the cut is made on the side of the LineLED
without the wire leads. LineLED cannot touch the metal endcap which will
shorten the circuit.
cut
LineLED
cut
3.1
wire leads
LineLED
3
3.1
STEP A STEP B STEP C
tighten at head screws below
extrusion surface before
installing LineLED
drill locations
for mounting
holes
countersink
holes for
at head
screws
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
lens
extrusion
4
2.1
4.1
aluminum
extrusion
5.1 Secure extrusion directly to wall with #4 flat head wood screws.
5
5.1
extrusion
screw
4.1

*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 2 of 2
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
9.1 Ensure the correct (wattage & voltage) power supply is used to
power LineLED. Then proceed to connect LineLED wires from
SlimLine extrusion to power supply. For more information please
refer to power supply and LineLED wiring instructions.
9
line voltage wires low voltage wires
class II power
supply
LineLED
extrusion
9.1
7.1 Snap the lens onto the extrusion.
7
lens
extrusion
7.1
8.1 Snap the endcaps onto the extrusion ends and secure using the 2 screws.
8
lens
extrusion
8.1
endcap
extrusion/lens
screw
REV0.1
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
QUE Channel - Installation Instructions