Makita KP001G User manual

KP001G
EN Cordless Planer INSTRUCTION MANUAL 11
ZHCN 充电式电刨 使用说明书 27
ID Mesin Serut Tanpa Kabel PETUNJUK PENGGUNAAN 43
MS Pengetam Tanpa Kord MANUAL ARAHAN 60
VI Máy Bào Cầm Tay Hoạt Động
Bằng Pin TÀI LIỆU HƯỚNG DẪN 77
TH   93

2
1
2
3
1
Fig.1
1
2
Fig.2
1
2
3
Fig.3
12
Fig.4
1 2 3 4
Fig.5
1
Fig.6
1
2
3
4
Fig.7
1
2
3
Fig.8

3
1
2
3
4
Fig.9
1
3
2
4
5
6
Fig.10
1
2
3
4
5
6
7
Fig.11
2
1
Fig.12
1
2
4
3
Fig.13
1
3
2
4
6
5
Fig.14

4
1
2
3
4
Fig.15
1
2
3
Fig.16
2
3
4
1
5
6
7
Fig.17
1
3
2
4
5
6
Fig.18
1
2
3
4
5
6
7
Fig.19

5
1
3
2
4
6
5
Fig.20
1
2
3
4
Fig.21
1
2
Fig.22
1
2
3
4
5
Fig.23
1
2
Fig.24
7
6
3
2
1
8
4
5
Fig.25
1
2
Fig.26

6
1
2
Fig.27
1
2
3
Fig.28
1
2
Fig.29
1
Fig.30
1
Fig.31
1
Fig.32
Fig.33
Fig.34

7
Fig.35
Fig.36
4
3
1
2
2
Fig.37
A
B
1
2
3
Fig.38
1
2
34
Fig.39
2
1
Fig.40
Fig.41
3
2
1
Fig.42

8
1
2
3
Fig.43
1
2
2
3
3
Fig.44
Fig.45
1
Fig.46
1
3
2
4
Fig.47
1
3
2
Fig.48
1
Fig.49

9
12
1
2
Fig.50
Fig.51
1
Fig.52
1
2
Fig.53
1
Fig.54
1
Fig.55

10
12
1
2
Fig.56
1
2
Fig.57
4
1
2
3
5
6
Fig.58
Fig.59

11 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: KP001G
Planing width 82 mm
Planing depth 4 mm
Shiplapping depth 25 mm
No load speed 15,000 min-1
Overall length (with BL4040) 385 mm
Rated voltage D.C. 36 V - 40 V max
Net weight 3.7 - 4.9 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
withoutnotice.
• Specicationsandbatterycartridgemaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombinations,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Batterycartridge BL4020*/BL4025*/BL4040*/BL4050F/BL4080F
*:Recommendedbattery
Charger DC40RA/DC40RB/DC40RC
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Symbols
Thefollowingsshowthesymbolswhichmaybeused
fortheequipment.Besurethatyouunderstandtheir
meaningbeforeuse.
Readinstructionmanual.
Wearsafetyglasses.
Ni-MH
Li-ion
OnlyforEUcountries
Duetothepresenceofhazardouscom-
ponentsintheequipment,wasteelectrical
andelectronicequipment,accumulators
andbatteriesmayhaveanegativeimpact
ontheenvironmentandhumanhealth.
Donotdisposeofelectricalandelectronic
appliancesorbatterieswithhousehold
waste!
InaccordancewiththeEuropeanDirective
onwasteelectricalandelectronicequip-
mentandonaccumulatorsandbatteries
andwasteaccumulatorsandbatteries,
as well as their adaptation to national law,
wasteelectricalequipment,batteriesand
accumulatorsshouldbestoredseparately
anddeliveredtoaseparatecollectionpoint
formunicipalwaste,operatinginaccor-
dancewiththeregulationsonenvironmen-
talprotection.
Thisisindicatedbythesymbolofthe
crossed-outwheeledbinplacedonthe
equipment.
Intended use
Thetoolisintendedforplaningwood.

12 ENGLISH
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm“powertool”inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless)powertool.
Work area safety
1. Keep work area clean and well lit.Clutteredor
darkareasinviteaccidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust.Powertoolscreatesparks
whichmayignitethedustorfumes.
3. Keep children and bystanders away while
operating a power tool.Distractionscancause
youtolosecontrol.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduceriskofelectricshock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.Thereisanincreasedriskofelec-
tricshockifyourbodyisearthedorgrounded.
3. Do not expose power tools to rain or wet con-
ditions.Waterenteringapowertoolwillincrease
theriskofelectricshock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.Damagedorentangledcords
increasetheriskofelectricshock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use.Useof
acordsuitableforoutdoorusereducestheriskof
electricshock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.UseofanRCDreduces
theriskofelectricshock.
7. Power tools can produce electromagnetic
elds (EMF) that are not harmful to the user.
However,usersofpacemakersandothersimilar
medicaldevicesshouldcontactthemakeroftheir
deviceand/ordoctorforadvicebeforeoperating
this power tool.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication.Amomentofinattentionwhileoperating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection.Protectiveequipmentsuch
asadustmask,non-skidsafetyshoes,hardhator
hearingprotectionusedforappropriateconditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.Carryingpowertoolswith
yourngerontheswitchorenergisingpowertools
thathavetheswitchoninvitesaccidents.
4. Remove any adjusting key or wrench before
turning the power tool on.Awrenchorakeyleft
attachedtoarotatingpartofthepowertoolmay
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times.Thisenablesbettercontrol
ofthepowertoolinunexpectedsituations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
longhaircanbecaughtinmovingparts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.Useof
dustcollectioncanreducedust-relatedhazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.Acarelessaction
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.

13 ENGLISH
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application.Thecorrect
powertoolwilldothejobbetterandsaferatthe
rateforwhichitwasdesigned.
2. Do not use the power tool if the switch does
not turn it on and o󰀨.Anypowertoolthatcannot
becontrolledwiththeswitchisdangerousand
mustberepaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools.Suchpreventivesafetymeasuresreduce
theriskofstartingthepowertoolaccidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.Powertoolsaredangerousinthe
handsofuntrainedusers.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Manyaccidentsarecausedbypoorlymaintained
power tools.
6. Keep cutting tools sharp and clean.Properly
maintainedcuttingtoolswithsharpcuttingedges
arelesslikelytobindandareeasiertocontrol.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.Useofthepowertool
foroperationsdi󰀨erentfromthoseintendedcould
resultinahazardoussituation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease.Slippery
handlesandgraspingsurfacesdonotallowfor
safehandlingandcontrolofthetoolinunexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled.Theentangle-
mentofclothworkglovesinthemovingpartsmay
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer.Achargerthatissuitablefor
onetypeofbatterypackmaycreateariskofre
whenusedwithanotherbatterypack.
2. Use power tools only with specically desig-
nated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatterytermi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritationorburns.
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
mayexhibitunpredictablebehaviourresultingin
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
peratureabove130°Cmaycauseexplosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions.Chargingimproperlyorattemperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts.Thiswillensurethatthesafetyofthepower
tool is maintained.
2. Never service damaged battery packs.Service
ofbatterypacksshouldonlybeperformedbythe
manufacturerorauthorizedserviceproviders.
3. Follow instruction for lubricating and chang-
ing accessories.
Cordless Planer Safety Warnings
1. Wait for the cutter to stop before setting the
tool down.Anexposedrotatingcuttermay
engagethesurfaceleadingtopossiblelossof
controlandseriousinjury.
2. Use clamps or another practical way to secure
and support the workpiece to a stable plat-
form.Holdingtheworkpiecebyyourhandor
againstthebodyleavesitunstableandmaylead
tolossofcontrol.
3. Rags, cloth, cord, string and the like should
never be left around the work area.
4. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
5. Use only sharp blades. Handle the blades very
carefully.
6. Be sure the blade installation bolts are
securely tightened before operation.
7. Hold the tool rmly with both hands.
8. Keep hands away from rotating parts.
9. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
10. Make sure the blade is not contacting the
workpiece before the switch is turned on.
11. Wait until the blade attains full speed before
cutting.
12. Always switch o󰀨 and wait for the blades to
come to a complete stop before adjusting
depth of cut.
13. Never stick your nger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
14. Do not leave the tool running. Operate the tool
only when hand-held.

14 ENGLISH
15. When replace the blades or some parts on the
drum, make sure to replace the parts on both
sides of the drum as a set. Otherwise,theresult-
ingimbalancewillcausevibrationandshortentool
life.
16. Use only Makita blades specied in this
manual.
17. Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
18. Operate the tool on stable condition. Operation
onunstableconditionmaycauseadamageinjury.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper with the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge.Suchconductmayresultina
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwardingagents,specialrequirementonpack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
inganexpertforhazardousmaterialisrequired.
Pleasealsoobservepossiblymoredetailed
nationalregulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
aroundinthepackaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita.Installingthebatteriesto
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge.Itmaycauseheating,catchingre,
burstandmalfunctionofthetoolorbatterycar-
tridge,resultinginburnsorpersonalinjury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec-
trical power lines.Itmayresultinamalfunction
orbreakdownofthetoolorbatterycartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.

15 ENGLISH
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wire-
less unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3. Use the wireless unit only with Makita tools.
4. Do not expose the wireless unit to rain or wet
conditions.
5. Do not use the wireless unit in places where
the temperature exceeds 50 °C (122 °F).
6. Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are nearby.
7. Do not operate the wireless unit in places
where automated devices are nearby.Ifoper-
ated,automateddevicesmaydevelopmalfunction
or error.
8. Do not operate the wireless unit in places
under high temperature or places where
static electricity or electrical noise could be
generated.
9. The wireless unit can produce electromagnetic
elds (EMF) but they are not harmful to the
user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doingsomaycauseamalfunctionofthewireless
unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged.Water,dust,anddirtcomeintotheslotmay
causemalfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary.Restorethelidifitcomeso󰀨
fromthetool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipo󰀨yourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
►Fig.1: 1.Redindicator2.Button3.Batterycartridge
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoras
showninthegure,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen.Ifnot,
itmayaccidentallyfalloutofthetool,causinginjuryto
youorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.

16 ENGLISH
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutso󰀨powertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placedunderoneofthefollowingconditions:
Overload protection
Whenthetool/batteryisoperatedinamannerthat
causesittodrawanabnormallyhighcurrent,thetool
automaticallystops.Inthissituation,turnthetoolo󰀨
andstoptheapplicationthatcausedthetooltobecome
overloaded.Thenturnthetoolontorestart.
Overheat protection
Whenthetool/batteryisoverheated,thetoolstops
automatically.Inthissituation,letthetool/batterycool
beforeturningthetoolonagain.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automatically.Inthiscase,removethebatteryfromthe
toolandchargethebattery.
Protections against other causes
Protectionsystemisalsodesignedforothercauses
thatcoulddamagethetoolandallowsthetooltostop
automatically.Takeallthefollowingstepstoclearthe
causes,whenthetoolhasbeenbroughttoatemporary
halt or stop in operation.
1. Turnthetoolo󰀨,andthenturnitonagainto
restart.
2. Chargethebattery(ies)orreplaceit/themwith
rechargedbattery(ies).
3. Letthetoolandbattery(ies)cooldown.
Ifnoimprovementcanbefoundbyrestoringprotection
system,thencontactyourlocalMakitaServiceCenter.
Indicating the remaining battery
capacity
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
lightupforafewseconds.
►Fig.2: 1.Indicatorlamps2.Checkbutton
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE:Dependingontheconditionsofuseandthe
ambienttemperature,theindicationmaydi󰀨erslightly
fromtheactualcapacity.
NOTE:Therst(farleft)indicatorlampwillblinkwhen
thebatteryprotectionsystemworks.
Adjusting depth of cut
CAUTION: Always switch o󰀨 and wait for the
blades to come to a complete stop before adjust-
ing depth of cut.
NOTE:Whenturningthedepthadjustmentknob,be
suretoholdthehandlermlywiththeotherhand.
Thecuttingdepthcanbeadjustedbyturningthedepth
adjustmentknobonthefrontofthetool.Turntheknob
toalignthepointerwithyourdesiredcuttingdepthon
thedepthscale.
►Fig.3: 1.Depthadjustmentknob2. Pointer 3. Depth
scale

17 ENGLISH
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
WARNING: NEVER defeat the lock-o󰀨 button
by taping down or some other means.Aswitchwith
anegatedlock-o󰀨buttonmayresultinunintentional
operationandseriouspersonalinjury.
WARNING: NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-o󰀨 button.Aswitchinneedofrepair
mayresultinunintentionaloperationandserious
personalinjury.ReturntooltoaMakitaservicecenter
forproperrepairsBEFOREfurtherusage.
NOTICE: Do not pull the switch trigger hard
without pressing in the lock-o󰀨 button.Thiscan
causeswitchbreakage.
Topreventtheswitchtriggerfrombeingaccidentally
pulled,thelock-o󰀨buttonisprovided.Tostartthetool,
depressandholdthelock-o󰀨button,andthenpullthe
switchtrigger.Releasetheswitchtriggertostop.
►Fig.4: 1.Switchtrigger2.Lock-o󰀨button
Foot
Thefootspringsoutoftherearbasewhenyouliftthe
toolupfromworksurfacestoavoidtheplanerblades
touchingtheworkpiecedirectly.Itpreventstheplaner
bladesfromaccidentaldamageswhennotinuse.
Thefootspringsbackintotherearbasewheneveryou
placethetoolbaseoverworksurfaces.
►Fig.5: 1.Planerblade2.Rearbase3.Foot4. Work
surface
Accidental restart preventive
function
Ifyouinstallthebatterycartridgewhilepullingthe
switchtrigger,thetooldoesnotstart.Tostartthetool,
releasetheswitchtrigger,andthenpulltheswitchtrig-
geragainwhiledepressingthelock-o󰀨button.
Electronic function
Thetoolisequippedwiththefollowingelectronicfunc-
tionsforeasyoperation.
Electric brake
Thetoolisequippedwithanelectricbrake.Ifthetool
consistentlyfailstoquicklystopafterreleasingthe
switchtrigger,havethetoolservicedatyourlocal
MakitaServiceCenter.
Soft start feature
Thesoft-startfunctionminimizesstart-upshock,and
makesthetoolstartsmoothly.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
Box wrench storage
Whennotinuse,storetheboxwrenchasshowninthe
guretokeepitfrombeinglost.
►Fig.6: 1.Boxwrench
Removing and installing planer
blades
CAUTION: Tighten the blade installation bolts
carefully when attaching the planer blades to
the tool. Always check to see they are tightened
securely.Alooseinstallationboltcanbedangerous.
CAUTION: Handle the planer blades very
carefully. Use gloves or rags to protect your n-
gers or hands when removing and installing the
planer blades.
CAUTION: Use only the Makita wrench pro-
vided to remove and install the planer blades.
Failuretodosomayresultinovertighteningorinsuf-
cienttighteningoftheinstallationbolts.Thiscould
causeaninjury.
NOTICE: To install planer blades, clean out all
chips or foreign matter adhering to the drum or
the planer blades. Use planer blades of the same
dimensions and weight, otherwise drum oscilla-
tion/vibration, causing poor planing action, and
tool breakdown will result.
For tool with conventional planer
blades
NOTE:Apairofplanerbladesareassembledin
thedrum.Repeatthefollowingproceduresforeach
planerblade.
Removing conventional planer blades
1. Unscrewtheinstallationboltsfromthedrumusing
theboxwrenchprovided.
2. Disassemblethedrumplateandconventional
planerblade(withadjustingplate)fromthedrum.
►Fig.7: 1.Installationbolt2.Drumplate
3.Conventionalplanerblade(withadjusting
plate) 4.Drum
3. Untightenthescrewsfromtheconventionalplaner
blade,andthenremovetheadjustingplate.
►Fig.8: 1.Screws2.Conventionalplanerblade
3.Adjustingplate

18 ENGLISH
Installing conventional planer blades
1. Setaconventionalplanerbladeontotheblade
gauge,aligningitscuttingedgealongtheguidewallon
thebladegaugehorizontally.
►Fig.9: 1.Conventionalplanerblade2.Bladegauge
3.Cuttingedge4.Guidewall
2. Placetheadjustingplateovertheconventional
planerblade,andthenslightlytightenthescrews.
3. Pushtheadjustingplateforwardsuntilitsposition-
ingguideneatlyandentirelytsalongtherearsidewall
ofthebladegauge.
4. Holdtheadjustingplatewhereitisandtightenthe
screwstosecureitinplace.
►Fig.10: 1.Adjustingplate2. Conventional planer
blade3.Screw4.Positioningguide5. Rear
side wall 6.Bladegauge
5. Cleanoutallthewoodchipsandforeignmatters
adheringtothedrumandconventionalplanerblade.
6. Slipthepositioningguideoftheadjustingplate
intotheguidegrooveinthedrum,andthenplacethe
drumplateovertheconventionalplanerblade(with
adjustingplate).
7. Cross-tightenalltheinstallationboltsevenlywith
theboxwrench.
►Fig.11: 1.Positioningguide2.Adjustingplate
3.Guidegroove4.Drum5.Drumplate
6.Conventionalplanerblade7. Installation
bolt
For tool with mini planer blades
NOTE:Apairofplanerbladesareassembledin
thedrum.Repeatthefollowingproceduresforeach
planerblade.
Removing mini planer blades
1. Loosentheinstallationboltsoneturnusingthe
boxwrenchprovided.
►Fig.12: 1.Installationbolt2.Boxwrench
2. Slidetheminiplanerbladeoutofthedrumby
pushingoneendofthebladeoutwardsfromthebelt
coverside.
►Fig.13: 1.Miniplanerblade2.Drum3.Beltcover4.
T-handleofboxwrench
NOTE:UsetheendsofT-handleoftheboxwrenchto
slidetheminiplanerbladeoutforsaferoperationand
maintenance.
Installing mini planer blades
1. Cleanoutallthewoodchipsandforeignmatters
adheringtothedrumandminiplanerblade.
2. Slideaminiplanerbladealongbetweenthedrum
andsetplatebypushingoneendofthebladeinwards
fromthesideoppositetothebeltcover.
3. Cross-tightenalltheinstallationboltsevenlywith
theboxwrench.
►Fig.14: 1.Miniplanerblade2.Drum3. Set plate
4.Beltcover5.Installationbolt6. Box
wrench
Mini planer blade calibration
Performacalibrationonplannerbladesatregularinter-
valstooptimizeworke󰀩ciency.
1. Loosentheinstallationboltsoneturnusingthe
boxwrenchprovided.
2. Slidetheminiplanerbladeoutofthedrumby
pushingoneendofthebladeoutwardsfromthebelt
coverside.
3. Unscrewtheinstallationboltsfromthedrumusing
theboxwrench.
4. Disassemblethedrumplateandsetplate(with
adjustingplate)fromthedrum.
►Fig.15: 1.Installationbolt2.Drumplate3. Set plate
(withadjustingplate)4.Drum
5. Loosenthescrewsonthesetplateoneturnto
disengagetheadjustingplate.
►Fig.16: 1.Screws2. Set plate 3.Adjustingplate
6. Cleanoutallthewoodchipsandforeignmatters
adheringtothesetplate(withadjustingplate)andmini
planerblade.
7. Settheminiplanerbladeontothebladegauge,
aligningitscuttingedgealongtheguidewallonthe
bladegaugehorizontally.
8. Placethesetplate(withadjustingplate)overthe
miniplanerblade,aligningtheguideridgesontheset
platewithguidegroovesontheminiplanerblade.
►Fig.17: 1.Miniplanerblade2.Bladegauge
3.Cuttingedge4.Guidewall5. Set plate
(withadjustingplate)6.Guideridge
7.Guidegroove
9. Pushtheadjustingplateforwardsuntilitsposition-
ingguideneatlyandentirelytsalongtherearsidewall
ofthebladegauge.
10. Holdtheadjustingplatewhereitisandtightenthe
screwstosecureitinplace.
►Fig.18: 1.Adjustingplate2. Set plate 3.Screw
4.Positioningguide5. Rear side wall
6.Bladegauge
11. Slipthepositioningguideoftheadjustingplate
intotheguidegrooveinthedrum,andthenplacethe
drumplateoverthesetplate(withadjustingplate).
►Fig.19: 1.Positioningguide2.Adjustingplate
3.Guidegroove4.Drum5.Drumplate
6. Set plate 7.Installationbolt
12. Slightlytightentheinstallationbolts,andslidethe
miniplanerbladealongbetweenthedrumandsetplate
bypushingoneendofthebladeinwardsfromtheside
oppositetothebeltcover.
13. Cross-tightenalltheinstallationboltsevenlywith
theboxwrench.
►Fig.20: 1.Miniplanerblade2.Drum3. Set plate
4.Beltcover5.Installationbolt6. Box
wrench

19 ENGLISH
Planer blade settings
Yourplaningsurfacewillenduproughanduneven,unlesstheplanerbladesaresetproperlyandsecurely.
Installplanerbladescorrectlysothecuttingedgessitinarightangle,onanabsolutelevelwiththerearbaseline,and
exactlyparalleltothesoleoftheplane.Readtheexamplesinthetableforpropersettings.
Planingsurface Blade setting Cause
Correctsetting
(A) (B)
(C)
Cuttingedgessitonalevelwith
therearbaselineandrunside
tosideparalleltothesoleof
the plane.
Gougingatstart
(A) (B)
(C)
Cuttingedgesunderreachthe
rearbaseline.
Gougingatend
(B)
(A) (C)
Cuttingedgesoverpassthe
rearbaseline.
Aslopeinsurface
(B)
(B)
(A)
(C)
Cuttingedgessitsidetoside
unparalleledtothesoleofthe
plane.
(A):Frontbase(Adjustableshoe)
(B):Rearbase(Fixedshoe)
(C):Planerblade
Installing guide rule
1. Laythetooldownwiththebeltcoverfacing
upwards.
2. Mounttheguideruleinplacebysecuringitwith
thethumbscrewintothemountingholeonsideofthe
tool head.
►Fig.21: 1.Beltcover2.Guiderule3.Thumbscrew
4.Mountinghole
3. Slidetheedgefenceinandouttoyourdesired
planingwidth,andthentightenthethumbscrewto
secureitintherequiredposition.
►Fig.22: 1.Edgefence2.Thumbscrew
Installing depth guide
1. Laythetooldownwiththebeltcoverfacing
downwards.
2. Mountthedepthguideinplacebysecuringitwith
thewasherandthumbscrewintothemountingholeon
sideofthetoolhead.
►Fig.23: 1.Beltcover2.Depthguide3. Washer
4.Thumbscrew5.Mountinghole
3. Slidethedepthguideupanddowntoyourdesired
planingdepth,andthentightenthethumbscrewto
secureitintherequiredposition.
►Fig.24: 1.Depthguide2.Thumbscrew
Installing chamfering rules
Optional accessory
1. Laythetooldownwiththefrontbasefacing
upwards.
2. Attachtheedgefencestothemountingarms,
aligningtheprojectionsonthearmswiththeguideslits
intheedgefences,andsecurethemwiththewashers
andthumbscrews.
3. Mountthechamferingrules(setsofedgefences
andmountingarms)inplacebysecuringthemwiththe
thumbscrewsintothemountingholesonbothsidesof
the tool head.
►Fig.25: 1.Frontbase2.Edgefence3.Mounting
arm 4.Projection5.Guideslit6. Washer
7.Thumbscrew8.Mountinghole
4. Slidetheedgefencesinandouttoyourdesired
chamferingrange,andthentightenthethumbscrewsto
securethemintherequiredposition.
►Fig.26: 1.Edgefence2.Thumbscrew

20 ENGLISH
Dust and wood chip extraction
Dustandwoodchipcanbereleasedfromeitherleftor
rightsideofdischargeopenings.Coveroneofthedis-
chargeopeningsonthesideopposedtoyourpreferred
dustextractiondirectionwiththestopper.
Todetachthestopperfromthedischargeopening,turn
thestoppertowardsthehandleslightlytodisengagethe
lock,andthenpullitapart.
►Fig.27: 1. Stopper 2. Handle
Asforinstallation,insertthestopperstraightintoone
oftheopeningsaligningthelockingslotinthestopper
withtheguideprojectionontheopeninguntilitlocksin
place.
►Fig.28: 1. Stopper 2.Lockingslot3.Guide
projection
Dust bag
Optional accessory
Attachthedustbagontooneofthedischargeopenings
andpushrmlyasfarasitwillgo.Makesurethedust
bagissecurelyplacedoverthetaperedopeningsoas
nottocomeo󰀨duringoperation.
►Fig.29: 1.Dustbag2.Dischargeopening
Whenthedustbagisabouthalffull,removethedust
bagfromthetoolandpullthefastenerout.Emptythe
dustbag.Tapthedustbaglightlytoremoveparticles
adheringinside,whichmighthamperfurthercollection.
►Fig.30: 1.Fastener
NOTE:IfyouconnectaMakitavacuumcleanerto
thistool,moree󰀩cientandcleaneroperationscanbe
performed.
Connecting a vacuum cleaner
Whenyouwishtoperformcleanplaningoperation,
connectaMakitavacuumcleanertoyourtool.Connect
ahoseofthevacuumcleanertooneofthedischarge
openingsasshowninthegure.
►Fig.31: 1.Vacuumcleaner
Elbow
Optional accessory
Useadustextractorelbowtocondenseextractionair
owatpreferredanglesforcleanerworkingenviron-
ment.Attachtheelbowintooneofthedischargeopen-
ingsandpushrmlyasfarasitwillgo.
►Fig.32: 1.Elbow
OPERATION
CAUTION:Holdthetoolrmlywithonehandon
theswitchhandleandtheotherhandonthedepth
adjustmentknobwhenoperatingthetool.
Planing operation
1. Holdthetoolrmlywithyourbothhands,one
handontheswitchhandleandtheotheronthedepth
adjustmentknob.
2. Placethefrontbaseofthetoolatuponthework-
piecesurfacewithouttheplanerbladesmakingany
contact.
3. Turnthetoolonandwaituntilitattainsfullspeed.
4. Gentlymovethetoolforwards,applyingslightly
moredownwardspressureonthedepthadjustment
knobatthestartsoastokeeptheentireplanerbase
levelandevenwiththeworkpiecesurface.
►Fig.33
5. Usecaretoapplypressureevenlyoverthework-
piecesurfaceinthemiddleofoperation,andpushthe
toolsteadilyforwards.
►Fig.34
NOTE:Balancehandpressurebetweentheswitch
handleanddepthadjustmentknobasboththefront
andrearbasescontacttheworkpiecesurface.
6. Applygreatercontrolontheswitchhandletoavoid
overreachingattheendofapasssincethefrontbase
willdropo󰀨theworkpiecesurface.
►Fig.35
NOTE:Planingcanbeeasierifyoupositionthework-
pieceataslightforwardtiltsoyoueaseuponthe
pressuretoholdthetoolduringoperation.
NOTE:Adjustthecuttingspeedanddepthforyour
desiredsurfacenishes.
Forroughnish,setthecuttingdepthsu󰀩ciently
deepenoughonworkpiece.
Forneatandnenish,pushthetoolslowlywith
shallowcuttingdepthandmakemorepasses.
Shiplapping (Rabbeting)
►Fig.36
Usetheguideruletomakeasteppedcutasshownin
thegure.
1. Installtheguideruleanddepthguideinthetool
andsecurethemwiththewashersandthumbscrews.
2. Adjustthedepthguidetotheshiplappingdepth
andsecureitinplacewiththethumbscrew.