Makita 4341T User manual

1
GB Jig Saw INSTRUCTION MANUAL
UA    
PL Wyrzynarka INSTRUKCJA OBSUGI
RO Ferstru pendular MANUAL DE INSTRUCIUNI
DE Stichsäge BEDIENUNGSANLEITUNG
HU Szúrófrész HASZNÁLATI KÉZIKÖNYV
SK Lupienková píla NÁVOD NA OBSLUHU
CZ
Elektronická pímoará pila s pedkyvem NÁVOD K OBSLUZE
4341T
4341CT
4341FCT

2
1
1 001931
1
2 001932
1
3 001933
1
4 001934
12
3
5 001935
1
6 001936
12
7 001937
1
2
8 001938 9 001939
1
2
3
10 001940
123
4
5
6
11 001941
1
2
3
12 001942
1
13 001943 14 001944 15 001945

3
1
2
16 001946 17 001947
1
2
18 001948
1
19 001949
1
2
3
20 001950 21 001951
1
2
3
22 001952 23 004449
1
2
24 004447
1
2
3
25 004448
1
2
26 001953
1
2
27 001954

4
ENGLISH
Explanation of general view
1-1. Cutting action changing lever
2-1. Switch lever
3-1. Speed adjusting dial
4-1. Tool opener
5-1. Blade clamp
5-2. Jig saw blade
5-3. Protrusions
6-1. Jig saw blade
7-1. Base
7-2. Hex wrench
8-1. Cutting line
8-2. Base
10-1. Base
10-2. Bolt
10-3. Hex wrench
11-1. Graduations
11-2. Bevel slot
11-3. Base
11-4. Bolt
11-5. Gear housing
11-6. V-notch
12-1. Base
12-2. Bolt
12-3. Hex wrench
13-1. Starting hole
16-1. Dust nozzle
16-2. Base
18-1. Dust nozzle
18-2. Hose for vacuum cleaner
19-1. Rip fence
20-1. Bolt
20-2. Fence guide
20-3. Hex wrench
22-1. Fence guide
22-2. Threaded knob
22-3. Circular guide pin
24-1. Bolt
24-2. Rule bar
25-1. Guide rail adapter
25-2. Screw
25-3. Guide rail
26-1. Cover plate
26-2. Base
27-1. Base
27-2. Anti-splintering device
SPECIFICATIONS
Model 4341T 4341CT 4341FCT
Length of stroke 26 mm 26 mm 26 mm
Wood 135 mm (* 110 mm) 135 mm 135 mm
Max. cutting capacities Steel 10 mm 10 mm 10 mm
Strokes per minute (min-1) 2,800 800 - 2,800 800 - 2,800
Overall length 271 mm 271 mm 271 mm
Net weight 2.4 kg 2.4 kg 2.4 kg
Safety class /II
* For European countries
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
END201-2
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
󻜎 Read instruction manual.
󻜎 DOUBLE INSULATION
󻜎 Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE019-1
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials. As a result of the extensive accessory
and saw blade program, the tool can be used for many
purposes and is very well suited for curved or circular
cuts.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
ENG004-2
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 85 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is 7 m/s2.
These values have been obtained according to
EN60745.

5
ENH101-5
Model; 4341T,4341CT,4341FCT
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki CE2005
000087
Director
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
GEB016-1
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to jig saw safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal
injury.
1. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3. Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the
workpiece before cutting so that the blade will
not strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
12. Do not touch the blade or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
13. Do not operate the tool at no-load
unnecessarily.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
15. Always use the correct dust mask/respirator
for the material and application you are
working with.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Selecting the cutting action
Fig.1
This tool can be operated with an orbital or a straight line
(up and down) cutting action. The orbital cutting action
thrusts the blade forward on the cutting stroke and
greatly increases cutting speed.
To change the cutting action, just turn the cutting action
changing lever to the desired cutting action position.
Refer to the table to select the appropriate cutting action.
Position Cutting action Applications
For cutting mild steel,
stainless steel and plastics.
For clean cuts in wood
and plywood.
Small orbit
cutting action
For cutting mild steel,
aluminum and hard wood.
For cutting wood and
plywood.
For fast cutting in aluminum
and mild steel.
Large orbit
cutting action
For fast cutting in wood
and plywood.
0Straight line
cutting action
Medium orbit
cutting action
006582
Switch action
Fig.2
CAUTION:
• Before plugging in the tool, always be sure that the
tool is switched off.
To start the tool, slide the switc h lever to the "I " positi on.
To stop the tool, slide the switch lever to the "O" position.

6
Speed adjusting dial
For 4341CT, 4341FCT
Fig.3
The tool speed can be infinitely adjusted between 800
and 2,800 strokes per minute by turning the adjusting
dial. Higher speed is obtained when the dial is turned in
the direction of number 5; lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
may differ with the type or thickness of the workpiece. In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Workpiece to be cut Number on adjusting dial
Wood 4 - 5
Mild steel 3 - 5
Stainless steel 3 - 4
Aluminum 3 - 5
Plastics 1 - 4
006581
CAUTION:
• The speed adjusting dial can be turned only as far
as 5 and back to 1. Do not force it past 5 or 1, or
the speed adjusting function may no longer work.
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Safety and soft start because of suppressed starting
shock.
Lighting up the lamps
For 4341FCT only
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing or removing saw blade
Fig.4
CAUTION:
• Always clean out all chips or foreign matter
adhering to the blade and/or blade holder. Failure
to do so may cause insufficient tightening of the
blade, resulting in a serious personal injury.
• Do not touch the blade or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
• Tighten the saw blade securely. Failure to do so
may cause a serious injury.
• When you remove the saw blade, be careful not to
hurt your fingers with the top of the blade or the tips
of workpiece.
To install the blade, open the tool opener to the position
shown in the figure.
Keeping that situation, insert the saw blade into the
blade clamp as far as the two protrusions of the blade
can not be seen.
Fig.5
Return the tool opener to its original position.
After installing, always make sure that the blade is
securely held in place by trying to pull it out.
CAUTION:
• Do not open the tool opener excessively, or it may
cause tool damage.
To remove the blade, open the tool opener to the
position shown in the figure. Pull the saw blade out
toward the base.
Fig.6
NOTE:
• Occasionally lubricate the roller.
Hex wrench storage
Fig.7
When not in use, the hex wrench can be conveniently
stored.
OPERATION
Fig.8
CAUTION:
• Hold the tool firmly with one hand on the switch
handle and the other hand on the front grip when
performing the tool.
• Always hold the tool base flush with the workpiece.
Failure to do so may cause blade breakage,
resulting in a serious injury.
Turn the tool on and wait until the blade attains full
speed. Then rest the tool base flat on the workpiece and
gently move the tool forward along the previously
marked cutting line. When cutting curves, advance the
tool very slowly.

7
Bevel cutting
Fig.9
CAUTION:
• Always be sure that the tool is switched off and
unplugged before tilting the base.
With the base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right).
Loosen the bolt on the back of the base with the hex
wrench. Move the base so that the bolt is positioned in
the center of the bevel slot in the base.
Fig.10
Tilt the base until the desired bevel angle is obtained.
The V-notch of the gear housing indicates the bevel
angle by graduations. Then tighten the bolt firmly to
secure the base.
Fig.11
Front flush cuts
Fig.12
Loosen the bolt on the back of the base with the hex
wrench and slide the base all the way back. Then tighten
the bolt to secure the base.
Cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole:
Fig.13
For internal cutouts without a lead-in cut from an
edge, pre-drill a starting hole 12 mm or more in
diameter. Insert the blade into this hole to start your
cut.
B) Plunge cutting:
Fig.14
You need not bore a starting hole or make a lead-in
cut if you carefully do as follows.
(1) Tilt the tool up on the front edge of the base
with the blade point positioned just above the
workpiece surface.
(2) Apply pressure to the tool so that the front
edge of the base will not move when you
switch on the tool and gently lower the back
end of the tool slowly.
(3) As the blade pierces the workpiece, slowly
lower the base of the tool down onto the
workpiece surface.
(4) Complete the cut in the normal manner.
Finishing edges
Fig.15
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear.
The underside of the workpiece can be greased instead
of using a coolant.
Dust extraction
Fig.16
Fig.17
The dust nozzle (accessory) is recommended to perform
clean cutting operations.
To attach the dust nozzle on the tool, insert the hook of
dust nozzle into the hole in the base.
The dust nozzle can be installed on either left or right
side of the base.
Then connect a Makita vacuum cleaner to the dust
nozzle.
Fig.18
CAUTION:
• If you try to remove the dust nozzle forcibly, the
hook of the dust nozzle can be diminished and
removed unintentionally during operation.
Rip fence set (optional accessory)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing
accessories.
1. Straight cuts
Fig.19
Fig.20
When repeatedly cutting widths of 160 mm or less, use
of the rip fence will assure fast, clean, straight cuts. To
install, insert the rip fence into the rectangular hole on
the side of the tool base with the fence guide facing
down. Slide the rip fence to the desired cutting width
position, then tighten the bolt to secure it.
2. Circular cuts
Fig.21
Fig.22
When cutting circles or arcs of 170 mm or less in
radius, install the rip fence as follows.
Insert the rip fence into the rectangular hole on the
side of the base with the fence guide facing up.
Insert the circular guide pin through either of the
two holes on the fence guide. Screw the threaded
knob onto the pin to secure the pin.
Now slide the rip fence to the desired cutting radius,
and tighten the bolt to secure it in place. Then
move the base all the way forward.
NOTE:
• Always use blades No. B-17, B-18, B-26 or B-27
when cutting circles or arcs.

8
Guide rail adapter set (accessory)
Fig.23
When cutting parallel and uniform width or cutting
straight, the use of the guide rail and the guide rail
adapter will assure the production of fast and clean cuts.
To install the guide rail adapter, insert the ru le ba r into
the square hole of the base as far as it goes. Secure the
bolt with the hex wrench securely.
Fig.24
Install the guide rail adapter on the rail of the guide rail.
Insert the rule bar into the square hole of the guide rail
adapter. Put the base to the side of the guide rail, and
secure the bolt securely.
Fig.25
CAUTION:
• Always use blades No. B-8, B-13, B-16, B-17 or 58
when using the guide rail and the guide rail
adapter.
Cover plate
Fig.26
Use the cover plate when cutting decorative veneers,
plastics, etc. It protects sensitive or delicate surfaces
from damage. Fit it on the back of the tool base.
Anti-splintering device
Fig.27
For splinter-free cuts, the anti-splintering device can be
used. To install the anti-splintering device, move the tool
base all the way forward and fit it from the back of tool
base. When you use the cover plate, install the
anti-splintering device onto the cover plate.
CAUTION:
• The anti-splintering device cannot be used when
making bevel cuts.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
To maintai n product SAFETY and RE LI AB ILIT Y, repa ir s,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Jig saw blades
• Hex wrench 4
• Rip fence (guide rule) set
• Guide rail adapter set
• Guide rail set
• Anti-splintering device
• Dust nozzle
• Cover plate
• Hose (For vacuum cleaner)

9

   
1-1.   
2-1.  
3-1.   
4-1.   

5-1.  
5-2.  
5-3. 
6-1.  
7-1. 
7-2.  
8-1.  
8-2. 
10-1. 
10-2. 
10-3.  
11-1. 
11-2.  
11-3. 
11-4. 
11-5.  
11-6. V- 
12-1. 
12-2. 
12-3.  
13-1.  
16-1.   
16-2. 
18-1.   
18-2.  
19-1.  
20-1. 
20-2.  
20-3.  
22-1.  
22-2.    

22-3.   
24-1. 
24-2. 
25-1.   
25-2. 
25-3.  
26-1. 
26-2. 
27-1. 
27-2.   
 
 4341T 4341CT 4341FCT
  26  26  26 
 135  (* 110 ) 135  135 
.    10  10  10 
    (.-1) 2800 800 - 2800 800 - 2800
  271  271  271 
  2,4  2,4  2,4 
  /II
*   
•  ,        ,       
 .
• .        .
END201-2

  ,   
 .  
,     .
󻜎    .
󻜎  
󻜎    
  
   
!
  
 2002/96/EC  
  
   
   
, ,
   ,  
    
,   
 .
ENE019-1

    ,
  .     
     
  ,  
     
    .
ENF002-1
 
     
,   ,    
 ,   
    
 .   
     , ,
     
.

10
ENG004-2
   
  
      
85  (A).
 3 (A).
       85
 (A).
   .
   
 7 /2.
      
EN60745.
ENH101-5
; 4341T,4341CT,4341FCT
  
     ,
      
  ;
EN60745, EN55014, EN61000   
   89/336/EEC, 98/37/EC.
  CE2005
000087

   .
-, , -, 
 MK15 8JD, 
 :
    
GEB016-1
  

     
    (
   ), 
    
   .  
   
 ,   
.
1.   ,   
    
   , 
    
 .    
      
     
  .
2.      
     
  .  
       
   .
3.      
.     
      
.
4.    . 
     
  .
5.      .
6.    '
,     
  ,     
,   ..
7.   .
8. ,    
  .
9.       .
10.    .
    , 
   .
11. '   
    
,      
.
12.      
 ,    
     .
13.      
   
14.      
  .  ,
      
.   
   .
15.   
/   
  ,  
.
  
:
   ,
     , 
   .