Maxon SD-270 Series User manual

SD-270 Series Data Radio
User Manual
January 2017

1
FCC RF Exposure Compliance Requirements
The Federal Communications Commission (FCC), with its action in General Docket
93-62, November 7, 1997, has adopted a safety standard for human exposure to
Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment.
Friendcom subscribes to the same safety standard for the use of its products. Proper
operation of this radio will result in user exposure far below the Occupational Safety
and Health (OSHA) and Federal Communications Commission limits.
About your SD-270 Series Data Radio
The SD-270 Series is a PLL synthesized 5-watt FM transceiver module, which is
designed for data transmission and voice communication. It can support
pre-emphasis, squelch CTCSS/DCS and audio amplifier. Two-point modulation
technology provides a good low frequency response and POCSAG protocol is
optional. The radio has a fast start-up time, low power consumption, and the
optional modem boards from 1200-19200 bps add extra applications for its use. The
die cast aluminum cabinet and lid provides resistance to RF interference with the
most requested mechanical footprint in the industry.
Should you have questions regarding the operation of the radio, please consult us at:
Maxon America, Inc. Phone: [phone]
11535 W. 83rd Terrace Email: [e-mail]
L e n e x a , KS 66214 Website: www.maxonamerica.com

2
Features
C E , F C C , MRC & AS/NZS 4295: 2015 certified
Programmable 16 channels (Dip Switch Select)
External Software Channel Steering
Configurable Power Save Feature
FSK, 4FSK& GMSK Modem Options; Supports 19200 bps
Frequency Step 6.25KHz
CTCSS/DCS Encode/Decode
Fast start-up time: 5ms
SQ Programmable via PC (6 Levels)
POCSAG Modulation (Optional)
PC Programmable & Software Tune & Calibration
Applications
Industrial telemetry & wireless remote control or Paging system
Gas and oil flow monitoring
Electricity, water and gas utilities
Earthquake, weather, environmental protection
Vehicle tracking and asset tracking systems
Water monitoring, waste water management and irrigation control
Railway, police, army automation system
Aerial defense and fire alarm system
Urban lighting control

3
Specifications
GENERAL
Working Frequency
V: 136-174 MHz
U0: 400-440 MHz
U1: 430-470 MHz
U2: 450-490 MHz
Channel Spacing
12.5KHz/25KHz Programmable
Modulation Type
F3D/F3E
Number of Channels
16
Nominal Working Voltage
12V DC
Extreme Working Voltage
9.6 V～16V DC
Storage Temperature
-40℃～+80℃
Operating Temperature
-30℃～+65℃
Current
Consumption
Standby
＜100mA (65 mA @ 12V)
Transmit 5 watts RF Power
＜1.5A
Transmit 1 watt RF Power
＜1A
TX to RX Attack Time
＜5ms
RX to TX attack time
＜5ms
Frequency Error
＜2.5ppm
Antenna Connector
BNC 50Ω
External interface
DB15 Female

4
TRANSMITTER Specification
R F P o w e r
1W/2W/3W/4W/5W Programmable
Frequency
Deviation
25KHz Channel Spacing
＜5KHz
12.5KHz Channel Spacing
＜2.5KHz
Subsonic
0.5KHz
Audio Response
25KHz Channel Spacing
300Hz～3KHz+1/-3dB
12.5KHz Channel Spacing
300Hz～2.55KHz +1/-3dB
Adjacent
Channel Power
25KHz Channel Spacing
＜-70dBc
12.5KHz Channel Spacing
＜-65dBc
Conducted Spurious Emission
＜1GHz,＜-36dBm
＞1GHz,＜-30dBm
Modulation
Sensitivity
V o i c e
8~15mV
Data
80~130mV
TX SNR
25KHz Channel Spacing
＞45dB
12.5KHz Channel Spacing
＞40dB
RECEIVER Specification
RX Sensitivity
(12dB SINAD)
25KHz Channel Spacing
＜-119dBm Extreme＜-115dBm
12.5KHz Channel Spacing
＜-119dBm Extreme＜-115dBm
Adjacent Channel
Selectivity
25KHz Channel Spacing
＞70dB
12.5KHz Channel Spacing
＞60dB
Image Rejection
＞70dB

5
IF Rejection
＞70dB
Spurious Rejection
＞70dB
Intermodulation Suppression
＞65dB
Conducted Spurious Emission
＜-57dBm
Receiving Audio Distortion
＜5%
RX SNR
25KHz Channel Spacing
＞45dB
12.5KHz Channel Spacing
＞40dB
Audio Output Power
0.5W @ 8Ωload
Exterior View
Description of radio components
①DB15 Female connector
②BNC Antenna connector
③LED (Red for TX, Green for RX)

6
SD-270 External DB15 female Pin Assignment
SD-270 Series is manufactured by default with modem,iftheradio doesnot havea
built-in modem; the corresponding pin is defined as empty.
Pin
No.
Function
Description
Note
①
AUDIO_IN
（MOD IN）
Audio input, 3Khz LPF, Modulation
sensitivity is 100mV.
AUDIO_IN is effective only
when Pin7 (MIC)isvacantor
with +5V high level. 3KHz
LPF filter existed in audio
channel.
②
AUDIO_OUT
（AF OUT）
A u d i o o u t p u t , 3 K h z L P F . O u t p u t l e v e l a t
60% frequency deviation is 250±50mV.
This line has an internal pull-up resistor
t o + 5 V .
③
PTT
T X c o n t r o l , a c t i v e l o w , o n l y w h e n P T T i s
active AUDIO_IN and MIC IN are
effective. This line has an internal pull-
u p t o 5 V .
④
B+
(9.6～16V DC)
Positive pole input from DC p o w e r ,
nominal +12V.
⑤
P R O G
( D A T A O U T )
Programming data output, 5V TTL
⑥
BUSY
Logical level output to indicate
whether there is a carrier or not. Low
lever means carrier, high level means
nocarrier.Thislinehasapull-up to
+ 5 V .
⑦
MIC IN/RSSI
MIC IN: Microphone input.
RSSI:Todetecttheairsignalstrength.
Jumper selectable.
Can directly connect to
e l e c t r e t s M I C , t h e D C v o l t a g e
of this pin should lower than
3.5V, then MIC transmission
can be activated.

7
⑧
P R O G
( D A T A I N )
Programming data input, 5V TTL
⑨
SPK/POCSAG
SPK: Audio output from the audio
amplifier, @ 8Ω.
POCSAG: To transmit POCSAG code.
Jumper selectable.
AUDIO_IN is effective only
when PIN7 (MIC) is vacant or
with +5V high level. 3KHz
LPF filter existed in audio
channel.
⑩
RXD
(MODEM)
Theserialdataisinputtomodem
through this pin. Default is RS232.
Thehardwareisoneof
RS232, RS485 or TTL/5V
when delivery.
⑪
TXD
(MODEM)
Serialdataisoutputfrommodemvia
this pin. Default is RS232.
Thehardwareisoneof
RS232, RS485 or TTL/5V
when delivery.
⑫
CD_OUT
(MODEM)
Logical level output to indicated
whetheracarrierornot.Lowleverfor
carrier, high level for no carrier.
⑬
NC
No connection
⑭
GND
Ground
⑮
NC
No connection
Antenna installation
Fasten the antenna to the radio by turning the antenna connector clockwise into the
receptacle on right of radio when looking at front of radio.
Powering the Data Radio
SD-270 accepts variable s o u r c e s o f D C p o w e r t o p e r m i t m o r e v e r s a t i l e u s e . T h i s r a d i o
o p e r a te s f ro m 9 . 6V to 1 6 V DC a n d s t a n d a rd v o l t a ge f o r te s t ing i s 1 2 V D C . T h e 4 th pin
of DB15 female connector is the power input pin.
SD-270 Series Function
Channel Spacing
Theradioiscapableofprogrammablechannelspacing,having12.5KHzor25KHz
channel spacing.

8
SQ (Squelch) Level
Six SQ leve ls are set in the radio and can be selected by PC software.
The audio signal will continuously transmit. Levels are shown as below:
Level 0 is for fully open mute.
Level 1：0.15uV
Level 2：0.25uV
Level 3：0.35uV
Level 4：0.45uV
Level 5：0.55uV
CTCSS/DCS
To help block out unwanted calls to your radio, the SD-270 can be programmed to
set CTCSS/DCS code. When enabled, receiver can only receive RF signal with the
sameCTCSS/DCScodeofthetransmittertoavoidinterference from unwanted
signals. For fast lock times, the CTCSS/DCS is not recommended for high speed data
transmission.
Channel Scan
The radio enables to detect the channels by initiate scanning mode. Scanning mode
is optional and programmable. Four scan modes are provided as shown below:
0 ---------normal scan with carry only
1 ---------normal scan, Carry with tone
2 ---------priority scan, Carry only

9
3 ---------priority scan, carry with tone
Channel Select
16 channels can be selected by inner dip (4) switch (HW)onpowerboardorserial
command inputted from our PC s o f t w a r e ( SW). Only in SW control mode, channel
can be selected by PC software in “Channel” feature.
Channel Dip Sw i t c h Chart
TX Protection
This feature, when enabled, limits the amount of time that the radio can
continuously transmit for p r o t e c t ing theradiofromblockofthechanneland
damageonradiowhichiscausedbysustained transmission. In TX mode, if PTT is
effective all through and exceed set time, radio will stop transmitting automatically
until restart the PPT again. The time is set by programming.
V o l u m e
The radio output voice via SPK Pin with 10 vo lume levels. The choice of appropriate