Mazda 0000-8C-Z02 User manual

GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
PART NUMBERS: APPLICABLE MODELS:
0000-8C-Z02 Electrochromic Mirror w/ Compass/ HomeLink® 2006 >Mazda3
0000-8C-L07 Compass / HomeLink® Installation Kit (non-rain sensor models)
REQUIRED COMPONENTS:
ITEM QTY DESCRIPTION SERVICE PART NUMBER
1 1 Mirror Assembly with Compass 0000-8C-Z02
INSTALLATION KIT COMPONENTS:
2 1 Harness Assembly – Power and Ground 0000-8C-H12
3 2 Wire Tap 000-8C-H09
4 4 Tie Wrap (Short) --
5 1 Wire Cover 000-8C-H11
6 1 Installation Instructions --
7 1 User Guide --
HOMELINK®AND THE HOMELINK HOUSE®ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC.
TOOLS REQUIRED:
Clean Rag Wire Cutters Ratchet
Fiberstick Electrical Tape 10mm Socket
Pliers #T20 Torx 4mm Flat Screwdriver
4
5
Page 1 of 8 Revision A 550-0336

INSTALLATION PRECAUTIONS / NOTES:INSTALLATION PRECAUTIONS / NOTES:
•Do not use excessive force when removing OE mirror from windshield.•Do not use excessive force when removing OE mirror from windshield.
•Do not place wire harness against objects with sharp edges that may cause electrical
shorting.
•Do not place wire harness against objects with sharp edges that may cause electrical
shorting.
•On vehicles equipped with “A” pillar air bag, verify mirror harness path remains clear of
air bag. Harness should follow, and be tied to existing OEM wiring with tie wraps.
•On vehicles equipped with “A” pillar air bag, verify mirror harness path remains clear of
air bag. Harness should follow, and be tied to existing OEM wiring with tie wraps.
•Verify that power harness path will not interfere with brake, clutch, emergency brake or
air bag operation. Use tie wraps to hold the wiring away from critical locations.
•Verify that power harness path will not interfere with brake, clutch, emergency brake or
air bag operation. Use tie wraps to hold the wiring away from critical locations.
1
Pe
rform the following pre-installation steps:
1
PP . Place kit components on a clean, padded
surface and inspect for damage or defects.
2. Record customer’s programmed radio stations (if
applicable).
1. Disconnect negative battery terminal.
a) Remove relay cover by grasping rear of
cover and pulling upwards. Disengage the
locking tab at the front of cover. (Fig. 1-1)
b) Remove two (2) 10mm bolts from
battery cover. Disengage locking tabs and
remove cover. (Fig. 1-2)
c) Disconnect negative battery terminal.
2. Remove driver-side scuff plate.r-side scuff plate.
a) Use fiberstick to disengage clips. (Fig. 1-3)a) Use fiberstick to disengage clips. (Fig. 1-3)
1 Preparation
Fig. 1-1
Fig. 1-2
10mm Bolts
Fig. 1-3
Page 2 of 8 Revision A 550-0336

3. Remove driver-side kick plate.
a) Use 4mm screwdriver to release center
of plastic push-pin.
b) Grasp kick plate at rear and pull out
towards passenger-side of vehicle.
(Fig. 1-4)
4. Loosen driver-side door seal past top
of A-pillar. (Fig. 1-5)
5. Remove A-pillar trim.
a) Pull out top of A-pillar trim towards
passenger-side of vehicle until A-pillar push-pin
connector is fully extended. (Fig. 1-6)
b) Pull A-pillar trim towards the rear of the
vehicle to release the base and to slide upwards
and off from A-pillar push-pin connector.
(Fig. 1-6)
6. Remove OE mirror.
a) Insert fiberstick between bottom of mirror mount
and windshield glass. (Fig. 1-7)
b) Push fiberstick up into mount to disengage
locking tab. Pull up while gently wiggling mirror
to remove.
Push-pin
Fig. 1-4
Fig. 1-5
CAUTION
!
A-pillar
Push-pin
Connector
Fig. 1-6
CAUTION
!
Do not use excessive force.
A
-pillar connector could be damaged.
Fig. 1-7
Page 3 of 8 Revision A 550-0336

1. Plug 10-pin connector into back of EC mirror.
(Fig. 2-1)
2. Attach EC mirror.
a) Hold the mirror head and slide the mount
downwards as far as possible over the windshield
button, until fully seated.
b) Using a #T20 Torx, tighten the mirror mounting
bracket screw to 1.3 ft-lbs (17.8 kg-cm).
(Fig. 2-2)
Fig. 2-1
2 EC Mirror Installation
NOTE
!
1. Route EC harness from mirror to headliner.
a) Route power harness into groove of wire
cover and attach wire cover to mirror base.
(Fig. 3-1)
b) Slide upper portion of wire cover up to headliner
so the “forks” are held by the headliner.
(Fig. 3-1)
2. Route EC harness to driver-side A-pillar.
a) Route power harness between vehicle headliner
and roof to top of driver-side A-pillar area.
(Fig. 3-2)
3 Route EC Mirror Harness to Vehicle Power
Fig. 3-2
1.3 ft-lbs
Fig. 2-2
Fig. 3-1
Slide harness sleeve as close to mirror connector as
p
ossible.
Page 4 of 8 Revision A 550-0336

3. Route EC harness down driver-side A-pillar.
a) Route power harness along factory harness in
driver-side A-pillar. (Fig. 3-3)
b) Secure power harness to factory harness with
three (3) tie wraps. (Fig. 3-3)
c) Cut excess material off tie wraps.
4. Route power harness to driver-side kick-plate area.
a) Route power harness through driver-side
instrument panel and into kick-plate area.
(Fig. 3-4)
1. Attach wire tap connectors to B+ and +12V ignition.
a) Locate the wire bundle in the driver-side kick
plate area. (Fig. 4-1)
b) Remove electrical tape wrapping as required
to access wires.
c) Locate Orange / Black-stripe wire (B+) in the
kick plate wire bundle.
d) Using pliers, secure wire tap to
Orange / Black-stripe wire. (Fig. 4-2)
e) Locate the Orange / Yellow-stripe wire (+12V)
in the bundle.
f) Using pliers, secure wire tap to
the Orange / Yellow-stripe wire. (Fig. 4-2)
Fig. 4-2
Fig. 3-4
Fig. 3-3
CAUTION
!
Tie
Wraps
CAUTION
!
Verify mirror harness path is clear of air bag (if equipped).
CAUTION
!
Do not tie wrap harness to sunroof drain tube (if equipped).
4 Connect Harness Power and Ground
Fig. 4-1
Remove
Tape
Orange /
Black-stripe
Wire
Orange /
Yellow-stripe
Wire
Page 5 of 8 Revision A 550-0336

Fig. 4-3
2. Connect EC power harness to ground.
a) Locate 10mm ground bolt, upper left of wire
bundle in driver-side kick-plate area. (Fig. 4-3)
b) Using 10mm socket, remove bolt.
c) Place ground ring from EC power harness, over
bolt and re-install bolt. (Fig. 4-3)
d) Tighten bolt to 80-90 in. lbs.
3. Connect EC power harness to B+ wire tap.
Ground
Wire
Fig. 4-4
Black /
White-stripe
to
Orange /
Yellow-stripe
Solid Black
to
Orange /
Black-stripe
a) Insert male spade terminal of solid black
harness wire into opening of wire tap on the
Orange / Black-stripe wire. (Fig. 4-4)
4. Connect EC power harness to +12V ignition.
a) Insert male spade terminal of black / white-stripe
harness wire into opening of wire tap on
the Orange / Yellow-stripe wire. (Fig. 4-4)
1. Bundle excess power harness and secure.
a) Bundle any excess power harness wires.
b) Secure bundled harness wires to factory wire
bundle with one (1) tie wrap. (Fig. 5-1)
1. Reconnect negative battery cable.
2. Turn the ignition switch ON/ACC position.
3. With the vehicle in a fairly well-lit area, perform the
following:
a) To make sure the auto-dimming feature is on,
verify that the green LED to the left of the
center switch is on. If it is not on, push the
switch to turn the green LED on.
b) Cover the forward looking photocell on the
back of mirror with a dark cloth or towel.
(Fig. 6-1)
NOTE
Fig. 5-1
!
Ensu
r
e male s
p
ade connectors are full
y
inserted into wire ta
p
s.
5 maining Harness WiresSecure Re
Tie Wrap
6 Testing
Dark Cloth or Towel
Rearward
Photocell
Green LED
Compass
Display Window
Fig. 6-1
Page 6 of 8 Revision A 550-0336

In a few seconds, the mirror will
begin to darken.
c) Remove the cover from the forward looking
photo cell and the mirror will begin to clear.
d) Verify that either a direction, such as NE, or
“C” is displayed in the display window. If not,
ensure the feature is turned ON by pressing the
button.
4. Turn the ignition key to the OFF position.
5. Push each HomeLink® button, one at a time, and
NOTE
verify that LED indicator to the left of the center
switch illuminates with a red LED. (Fig. 6-2)
6. Testing is now complete.
1. Trim excess off all wire ties.
2. Reinstall in reverse order, all trim pieces removed
during installation.
3. Place User Guide in vehicle glove-box.
(Fig. 7-1)
4. Remove fingerprints, smudges, dirt, etc. from mirror.
5. Verify each reinstalled component for proper fit and
function.
1. Adjust compass zone after EC mirror installation.
a) The zone setting is factory preset to Zone 8.
Refer to Compass Calibration Zone Map
(Fig. 8-1) to find correct compass zone setting
for your geographical location. Use same map
from User Guide.
b) To change the zone setting, push and hold the
right button until a number appears in the display.
Press button repeatedly until desired compass
zone number is reached.
!
Time to darken will var
y
with ambient li
g
ht level.
Red LED
HomeLink Buttons
Fig. 6-2
7 Installation of Removed Components
Fig. 7-1
User Guide
8 Compass Zone Adjustment (Dealer Install ONLY)
1
2
3
4
5
678
9
10
11
12
13
14
15
2
3
4
5
678910 11 12 13
14
Fig. 8-1
Page 7 of 8 Revision A 550-0336

1. Calibrate compass.
a) Drive to an open, level area, away from large
metallic objects or structures.
b) Hold the right button for approximately 9 seconds
until “C” text appears in the display. Release
the right button to enter the calibration mode.
c) Drive slowly in up to 3 circles until the “C”
disappears, and a directional heading is
displayed. The compass is now calibrated.
9 Compass Calibration (Dealer Install ONLY)
Page 8 of 8 Revision A 550-0336