Mazda 0000-8G-K01 User manual

AS 090-M11356cmc1105RevA
Page 1 of 4
Genuine Accessories
Installation Instructions
Part Number
0000-8G-K01
Applicable Models:
2004 Mazda RX8 Base
Package Contents
Front Mask
U-Nut (Qty. 8)
Tools Required
Stubby Phillips
Screwdriver
Hood Cover (Qty. 1)
Snap Head Screw (Qty. 8) Front End Cover (Qty. 1)
0Before Installation
A. Area to be covered by mask must be clean. It is recommended that you wash and wax vehicle prior to installation.
B. Both vehicle and mask must be completely dry prior to installation. If moisture under mask is allowed to dry on
vehicle, paint may cloud.
C. Any repainted surfaces in contact with mask must be allowed to cure completely. Consult paint manufacturer or
repair facility if you are not sure.
1Install Hood Cover
A. With hood open, stretch hood cover (A)
onto hood, pulling each side one or two
inches at a time, until corners fit snugly.
Install hooks on ends of straps (B) into
corresponding holes in hood. Pull
evenly on ends of adjustable straps (B)
until tight. Secure loose ends in elastic
loops.
Washer (Qty. 8)
2
1
3
A
BB

Page 2 of 4
AS 090-M11356cmc1105RevA
2Remove wheel well fasteners
A. Using stubby phillips screwdriver, remove five plastic
fasteners along front edge of both front wheel wells.
A. In both front wheel wells, lift wheel well liner to reveal holes.
B. Slip u-nuts (C) over top two and bottom two holes in metal edge,
making sure that holes are aligned.
C. Release liner to its original position. Using a stubby phillips
screwdriver, install washer (D) and snap head screws (E) into top
two and bottom two holes in each wheel well. Reinstall
original fastener into unoccupied middle hole.
3Install wheel well hardware
C
C
D
D
E
E
E
4Install upper attachments
A. With hood open, lay front end cover over
front of vehicle. On both sides of vehicle,
slide pockets (F) over front corners
of fenders. Care should be taken
to prevent ripping of pockets (F).
B. Attach clips (G) to edge of fender
rails.
C. On both sides of vehicle, insert
pads (H) in slot under headlights.
D. Attach clips (J) to back inside
edge of metal at center of vehicle
under hood.
HH
F
J
GFG

Page 3 of 4
AS 090-M11356cmc1105RevA
5
6Install bottom attachments
7Post Installation Inspection
A. Close hood and check alignment between hood
cover and front end cover along seam (between
fender and hood). If adjustment is necessary, adjust
the hood cover by adjusting the hood cover straps.
Refer to step 1.
B. If mask should flap due to high speed or wind
conditions, adjust or remove mask completely.
8Care and Cleaning
A. Always remove mask before washing vehicle.
B. Hand clean mask using mild soap, rinse thoroughly with
clean water and line dry completely. Do not machine dry!
C. Use Mazda Vinyl/Leather Protectant (or equivalent) to
preserve color and finish.
D. WARNING: Running up on curb will damage this product.
Manufacturer will not be responsible for damage to product
due to accident or misuse.
Place in vehicle glove compartment.
A. Insert pads (L) into slot located between edge of front facia and top edge of grille area. Attach clips (M) to back edge of facia in
fog light area. Attach clips (N) to underside edge of bumper facia. Insert velcro loop (O) into nearby hole in grille area and
attach to velcro hook (P) located at underside edge of bumper facia.
Install wheel well
attachments
A. Press snaps (K) onto snap head
screws (E) in both front wheel wells.
P
N
O
N
M
MLLL
K
KE
4x
3x
6x
O