Meanwell MP450 User manual

MP450 / 650 / 1K0
Instruction Manual

MP450,650,1K0 Instruction Manual
0. Introduction................................................................................................................
1
1
1
1
1
2
2
5
5
8
8
5
8
9
10
9
10
9
10
9
5
5
5
5
5
5
6
6
6
7
7
3
1. Order Information.......................................................................................................
2. Mechanical Specification and Output Terminals.......................................................
3. Functions...................................................................................................................
4. .....................................................................................................Notes On Operation
6.Specification...............................................................................................................
5.Series Parallel Connection Accessory/......................................................................
1.1 Explanation for Encoding .............................................................................................
2.1 Mechanism of the Whole Power System ..........................................................................
3.1 Input Voltage Range ....................................................................................................
4.1 Requirement for Assembly ............................................................................................
3.2 Inrush Current Limiting ................................................................................................
4.2 ...................................................................................................... Installation Method
4.3
.................................................................................................................... Derating
6.1 Front End
.........................................................................................................................
5.1 Series Connection Accessory ...........................................................................................
6.2 Output Module ..................................................................................................
5.2 Parallel Connection Accessory .............................................................................
3.3 Output Voltage Adjustment Range ..................................................................................
3.4 Short Circuit Protection & Over Current Protection (O.C.P.) ................................................
3.5 Over Voltage Protection (O.V.P.) .....................................................................................
3.6 Over Temperature Protection (O.T.P.) ..............................................................................
3.7 Fan Alarm. .................................................................................................................
3.8 Remote Sense - Output Modules ....................................................................................
3.9 Auxiliary Output. .........................................................................................................
3.10 Remote ON/OFF Control - Whole Power System ..............................................................
3.11 Remote ON/OFF Control - Output Modules .....................................................................
3.13 Parallel Operation ......................................................................................................
3.14 Series Operation ..............................................................................................
2.2 Mechanism of Output Modules ......................................................................................
1.3 Marking .....................................................................................................................
1.2 Notes on Encoding ......................................................................................................
6
3.12 Remote Margin V Program / - ...............................................................................
May. 2021 Version 9

0. Introduction
MP450,650,1K0 Instruction Manual
1. Order Information
Modular Series are switching power supplies with modular design that consist of two stages: front-end PFC and output modules.
Using ZVS (Zero Voltage Switching) technology to realize the power factor correction, the line input is rectified into high DC voltage
(around 390VDC) by the front-end PFC stage, and then the DC output modules will transfer the operating voltage into all kinds of
DC output voltages. Right now we offer six-categories totally 57 different kinds of models - 75W(MS-75), 150W(MS-150), 210W(MS-210)
300W(MS-300), 360W(MS-360) single output modules and 100W(MD-100) dual output modules - to fulfill all kinds of applications.
◎Please map out output modules that need to be connected in series or parallel at adjoining slots.
◎Total wattage usage of all output modules should be less than the rated power of front-end PFC stage.
◎Please refer to the marking on the safety label in front of the machine before using it.
1.1 Explanation for Encoding
1.2 Notes on Encoding
1.3 Marking
Figure 1-1 Safety labels
1
MP --
Parallel or option code
(See Table 1.)
450/650/1K0(450W/650W/1000W)
Modular Power with PFC
※450W/650W(5SLOT)
※1000W(7SLOT)
SLOT1 SLOT2 SLOT3 SLOT4 SLOT5 SLOT6 SLOT7
Table 1. Parallel code(For MS-210 MS-300 MS-360 only)、、
CodeModel
MS-300/360
MS-210
X
1
2
3
4
5
6
7
8
9
◎
◎
◎
◎
◎
◎
◎◎◎
◎◎◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
SLOT1 SLOT2 SLOT3 SLOT4 SLOT5 SLOT6 SLOT7
-----
-----
-----
-----
-----
-----
※Code X,1,2,7,8,9 for MP450, MP650
※Code X,1,2,3,4,5,6,7,8,9 for MP1K0
※Maximum number of units for parallel function : 5 for MS-210, 3 for MS-300/360
Example: MP1K0- 1C 2 2EK#S
SLOT1 O/P:5V@35A
SLOT2,3 O/P:12V@25A
SLOT4 Blank Slot
SLOT5 O/P:5V@10A
[email protected]
SLOT6,7 O/P:[email protected]
MP450-EKLMO
48V
3.2A
12V
13A
3.3V
15A
15V
5A
5V
15A
SLOT1 SLOT2 SLOT3 SLOT4 SLOT5
-
+
-
+
-
+
-
+
-
+
S/N:
INPUT: 100-240VAC
TOTAL OUTPUT POWER 450W( ax.)
6.3A 50/60Hz
MADE IN TAIWAN
MP650-CCEHH
5V
25A
5V
25A
12V
13A
24V
6.5A
24V
6.5A
SLOT1 SLOT2 SLOT3 SLOT4 SLOT5
-
+
-
+
-
+
-
+
-
+
S/N:
INPUT: 100-240VAC
TOTAL OUTPUT POWER 650W( ax.)
9.0A 50/60Hz
MADE IN TAIWAN
MP1K0-CDEHIJK
INPUT: 100-240VAC
5V
25A
7.5V
18A
12V
13A
24V
6.5A
27V
5.8A
33V
4.7A
48V
3.2A
SLOT1 SLOT2 SLOT3 SLOT4 SLOT5 SLOT6 SLOT7
13.5A 50/60Hz
TOTAL OUTPUT POWER 1000W( ax.)
MADE IN TAIWAN
-
+
-
+
-
+
-
+
-
+
-
+
-
+
S/N:
MEAN WELL ENTERPRISES CO.,LTD. MEAN WELL ENTERPRISES CO.,LTD.
No. 28 Wuquan 3rd Rd., Wugu Dist., New Taipei City 24891, Taiwan,No. 28 Wuquan 3rd Rd., Wugu Dist., New Taipei City 24891, Taiwan,
MEAN WELL ENTERPRISES CO.,LTD.
No. 28 Wuquan 3rd Rd., Wugu Dist., New Taipei City 24891, Taiwan,
E183223
Bauar
Sicherheit
egel gema
tgepru ft
od
be
www.
ID 2000000000
tuv.com
wac g
os
E183223
Bauar
Sicherheit
egel gema
tgepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os
E183223
Bauar
Sicherheit
egel gema
tgepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os

2. Mechanical Specification and Output Terminals
2.1 Mechanism of the Whole Power System
Unit:mm
CN4(PFC-450/650/1K0) : JST B3B-XH or equivalent
Pin No.
1
3
2
Assignment
-RC: -Remote ON/OFF
VCC: 12V/0.1A auxiliary output
+RC: +Remote ON/OFF
Mating Housing
JST XHP
or equivalent
Terminal
JST SXH-001T-P0.6
or equivalent
Pin No.
1
3
2
Assignment
AC/L
FG
AC/N
TB1(PFC-450/650/1K0)
2
◎MP450
◎MP650
◎MP1K0
4-M4
19 16 max.
12.5
38
63.5
147.5
254
19
101.5
127
12.25
147.5
8-M4(Both Sides)
12 max.
10 8.2
TB1
321
Air flow
direction
CN4
3
1
2
101.5
19
38
19
278
171.5
10 8.2
171.5
127 63.5
32
2
1
3
CN4
1
TB1
12.5
4-M4
12.25
direction
Air flow
8-M4(Both Sides)
12 max.
16 max.
direction
Air flow
TB1
321
2
3
1CN4
19
12.5
38
63.5
171.5
278
8.2 10
4-M4
19
177.8
152.4
15.65
171.5
8-M4(Both Sides)
12 max.
16 max.

2.2 Mechanism of Output Modules
3
Unit:mm
◎MS-150
◎MS-210
◎MS-75
3
4
2JSTXHP
or equivalent
JST SXH-001T-P0.6
or equivalent
+S: +Remote sensing
-S: -Remote sensing
+RC: +Remote ON/OFF
-RC: -Remote ON/OFF
Output Connector(CN51) : JST B4B-XH or equivalent
Pin No.
1
Assignment Mating Housing Terminal
Output Connector(CN20) : JST B4B-XH or equivalent
Pin No.
1
3
4
2
Assignment Mating Housing
JST XHP
or equivalent
Terminal
JST SXH-001T-P0.6
or equivalent
+S: +Remote sensing
-S: -Remote sensing
+RC: +Remote ON/OFF
-RC: -Remote ON/OFF
NOTE: 1.The voltage difference among each output should be minimized that less than 2% is required.
2.The total output current must not exceed the value determined by the following equation.
(Output current at parallel operation) = (The rated current per unit) (Number of unit) 0.9××
Output Connector(CN7) : HRS DF11-8DP-2DS or equivalent
Pin No. Pin No.
15
37
48
26
Assignment Assignment Mating Housing
HRS DF11-8DS
or equivalent
Terminal
DRS DF11-**SC
or equivalent
+S: +Remote sense CS: Current sharing
-S: -Remote sense G: GND
+RC: +Remote ON/OFF ML: Remote margin low control
-RC: -Remote ON/OFF M: Remote margin control
SVR1
+V
-V
60
21 max.
16 max.
CN51
1
4
138
3 max.
4
1
SVR2
CN20
21 max.
138
60
-V
+V
16 max.
3 max.
8
7
2
1
CN7
SVR2
21 max.
138
60
-V
-V
+V
+V
16 max.
3 max.

4
◎MD-100
NOTE: 1.Remote ON/OFF of CN4 turn ON/OFF the entire power system
2.Remote ON/OFF of CN20,CN33,CN41,CN51 turn ON/OFF the individual output module
3.SVR1~5: DC output voltage adjustment(SVR4 for CH2 of MD-100,SVR5 for CH1 of MD-100)
Output Connector(CN41) : JST B2B-ZR or equivalent
Pin No.
1
2
Assignment
+RC
-RC
Mating Housing
JST ZHR-2
or equivalent
Terminal
JST SZH-002T-P0.5
or equivalent
◎MS-300
◎MS-360
Output Connector(CN33) : JST B6B-XH or equivalent
Pin No.
1
3
5
4
6
2
Assignment Mating Housing
JST XHP
or equivalent
Terminal
JST SXH-001T-P0.6
or equivalent
+S: +Remote sensing
-S: -Remote sensing
+RC: +Remote ON/OFF
-RC: -Remote ON/OFF
CS:Current sharing
G:GND
NOTE: 1.The voltage difference among each output should be minimized that less than 2% is required.
2.The total output current must not exceed the value determined by the following equation.
(Output current at parallel operation) = (The rated current per unit) (Number of unit) 0.9××
Pin No. Pin No.
15
37
48
26
Assignment Assignment Mating Housing
JST XHP
or equivalent
Terminal
JST SXH-001T-P0.6
or equivalent
+S: +Remote sense CS: Current sharing
-S: -Remote sense G: GND
+RC: +Remote ON/OFF ML: Remote margin low control
-RC: -Remote ON/OFF M: Remote margin control
3 max.
Output Connector(CN7) : JST B8B-XH or equivalent
NOTE: 1.The voltage difference among each output should be minimized that less than 2% is required.
2.The total output current must not exceed the value determined by the following equation.
(Output current at parallel operation) = (The rated current per unit) (Number of unit) 0.9××
SVR3
+V
CN7
18
-V
+V
60
-V
138 16 max. 42 max.
3 max.
SVR3
+V
CN33
16
-V
+V
60
-V
138 16 max. 42 max.
3 max.
2
SVR5
CN41
1
SVR4
21 max.
138
60
+V1
GND1
+V2
GND2
16 max.

3. Functions
3.1 Input Voltage Range
3.2 Inrush Current Limiting
3.3 Output Voltage Adjustment Range
3.4 Short Circuit Protection & Over Current Protection (O.C.P.)
3.5 Over Voltage Protection (O.V.P.)
3.6 Over Temperature Protection (O.T.P.)
3.7 Fan Alarm
3.8 Remote Sense - Output Modules
◎Nominal input voltage range is AC 85~264V or DC 120~370V.
◎To insure proper operation, AC input should be within the pre-specified range. The wrong input will cause the power supply to
operate improperly, lose the PFC function or even be damaged.
◎Since the Modular Series have built-in active PFC circuit, there will be lower efficiency and output derating is required when
operating at lower input voltage (<100VAC).
◎Built-in inrush current limiting circuit.
◎Minor adjustments can be made to the output voltage of all channels by using a potentiometer. Turning clockwise will increase
output voltage and counterclockwise will decrease output voltage.
◎Built-in short circuit and over current protection function in each output module. O.C.P. comes into effect at >116% of output rated
current and the output module will automatically recover once the over current condition is removed. (MS-75/150/210/300/360
are constant current type while MD-100 is shut-off type)
◎Built-in over voltage protection circuit for each output channel.
◎Built-in 2 sets of over temperature protection circuit. When the internal temperature exceeds the threshold value, the power supply
will shut down automatically. You should switch off V and remove all possible causes of overheating, and then let the power supply
AC
cool down to normal working temperature (needs about 10 minutes~1hour) before turning it back on.
◎Built-in fan malfunction protection circuit. When the DC fan stop operating (fan lock, wire broken, or connector loosed), all output
modules will be shut down. Please switch off V and send back to our local distributor or MEAN WELL for repair.
AC
◎When using this function, the sensing wires should either be twisted or shielded to prevent external noise interference.
(refer to figure 3-1)
◎Built-in remote sense circuit in MS-75, MS-150, MS-210, MS-300 and MS-360.
◎When Remote Sense is not in use, +S should be shorted to +V and -S to -V. Or +S and -S can be left unconnected.
◎The voltage drop across the output wires must be limited to less than 0.5V. Also heavy wires with adequate current rating should be used
between +V/-V and the load. Please firmly connect the output wires to prevent them from loosing, or the power supply may be out of order.
◎If long sensing wires are necessary, then Noise Filtering Capacitors C1,C2 and C3 need to be added as figure 3-1.
◎The power supply unit may become unstable due to the difference in wire impedance and load current. The addition of C1, C2, C3 and
R1 shown in figure 3-1 may help improve output voltage stability. Please contact MEAN WELL for more detail specification of these
components.
◎The O.V.P. triggering points are different for different output modules. Please refer to the specification sheet for details.
◎The output module shuts down when O.V.P. is triggered. To restart power supply, please switch off V first and then wait for 10
AC
seconds before switching it back on.
◎When the output is tuned to a higher voltage, please notice that the load current should be decreased accordingly. The output
wattage of each module should not exceed its rated value under any circumstances.
◎The external switch, if needed, should have a current rating exceeding the maximum inrush current.
◎Since the inrush current limiting circuit mainly consists of thermistor and relay, after turning off the power supply, a 10 second
cool down period is recommended before turning it back on. Inrush current will be much higher than the specified value if input
thermistor is not allowed sufficient time to cool down.
5
-V
Output
C2C1
+V
TWISTED R1
LOAD C3
-RC
+RC
-S
+S
TWISTED
Figure 3-1 Connection for using the remote sense function
CN33 of MS-300
CN7 of MS-360
CN7 of MS-210
CN20 of MS-150
CN51 of MS-75

+RC
-RC
Vcc
12V/0.1A
SW
1
2
3
CN4
Vcc
12V/0.1A
3
-RC 2
+RC 1
TTL Level Signal
TTL Level Signal
Figure 3-2 Connection for the remote ON/OFF control function of the whole power system
Output
Module
Figure 3-3 Connection for the remote ON/OFF control function of output modules
Vcc
-RC
CN4 CN4
Front End Front End
+RC
Module
Output
+RC
-RC
Vcc
12V/0.1A12V/0.1A
-RC
+RC
+RC
1KΩ
-RC
CN4
3.9 Auxiliary Output
3.10 Remote ON/OFF Control - Whole Power System
◎Built-in 12V/0.1A auxiliary output that can be used as the voltage source of remote ON/OFF control application for individual
output modules or the whole modular system. Please refer to figure 3-2 and 3-3 for wiring methods.
◎Built-in remote ON/OFF control circuit for the whole power system.
◎The remote control circuit (+RC and -RC) has electric isolation from V and V .
in out
◎When there's a 4~12V voltage difference or open circuit between +RC & -RC, the whole power system will be turned off. The power
supply will be turned on if the voltage difference between +RC & -RC is less than 0.8V or short circuit. ( The whole power system will
have no output if the shorting connector is not assembled between +RC & -RC on CN4.)
◎The auxiliary output on the power supply can be used as the external control source of the remote ON/OFF control function.
Please refer to figure 3.2 for connecting methods.
3.11 Remote ON/OFF Control - Output Modules
◎Built-in remote ON/OFF control circuit for each output module. All output modules can be turned ON/OFF independently by using
the remote ON/OFF control function.
◎The remote control circuit (+RC and -RC) has electric isolation from V and V .
in out
◎The auxiliary output on the power supply can be used as the external control source of the remote ON/OFF control function on each
output module. Please refer to figure 3.3 for connecting methods.
◎When there's a 4~12V voltage difference between +RC & -RC, the output module will be turned off. The power supply will be turned
on if the voltage difference between +RC & -RC is less than 0.8V or open circuit.
6
CN33 of MS-300 CN33 of MS-300
CN7 of MS-360 CN7 of MS-360
CN7 of MS-210 CN7 of MS-210
CN20 of MS-150 CN20 of MS-150
CN51 of MS-75 CN51 of MS-75
CN41 of MD-100 CN41 of MD-100
3.12 Remote Margin V Program/-
◎Remote Margin / V- Program is available for MS-210 and MS-360 to fine tune the output voltage. Hereunder is the instruction,
assuming no voltage adjustment is applied via the built-in potentiometer.
(1) Connecting PIN CN7-6 with PIN CN7-8 will increase the output voltage by approximately 5% of the rated voltage.
Figure 3-4
Figure 3-5
(2)Connecting PIN CN7-6 with PIN CN 7-8 will reduce the output voltage by approximately 5% of the rated voltage.
CN7-6
CN7-7
CN7-8
CN7-8

7
Figure 3-7 Operating in parallel connection
◎Please connect the +S,-S,CS and G of each output module in parallel as well.
V- V-
V+ V+
MS-300 MS-360CN33 CN7
CN33 CN7
MS-300 MS-360
V- V-
LOAD LOAD
G G
G
ML
ML
M
M
CS CS
CS
+RC +RC
+RC
-RC -RC
-RC
-S -S
-S
+S +S
+S
-RC
CS
G
+RC
+S
-S
V+ V+
◎Please adjust the output voltages to the required value before wiring the output modules. The voltage difference among output
modules should be minimized that less than 2% is required.±
◎All wirings should be properly connected before turning on. The power supply can not be hot swapped.
◎Please connect the output terminal of each output module in parallel first and then connect to the load as shown in Figure 3-7.
Don't connect to the load separately.
3.13 Parallel Operation
◎MS-210, MS-300 and MS-360 are allowed to work in parallel.
◎Only same output modules adjoining one another inside the same power supply are recommended to connect in parallel.
◎The total output current should not exceed 90% of the sum of rated currents.
For example: MP650-2C2CO-1
Parallel code "1" means that the two MS-300-2C(5V/50A) located at SLOT 1,2 & SLOT 3,4 should be connected in parallel and the
maximum output current is 90A [(50A+50A)*0.9].
Figure 3-8 Operating in series connection
3.14 Series Operation
◎Higher output voltage can be acquired by using MS-75, MS-150, MS-210, MS-300 or MS-360 in series connection.
◎Only output modules with the same output wattage and adjoining one another are recommended to connect in series
◎Output current for series connection should not exceed the smallest rated current of all series connecting modules.
◎The difference in rise times of individual output module will lead to steps/stairs like turn on.
◎The output voltage after series connection should be less than 60Vdc [the requirement of SELV(Safety Extra Low Voltage) of IEC60950-1].
LOAD LOAD LOAD
V- V-V-
V+ V+V+
MS-300 MS-360MS-210
MS-300 MS-360MS-210
V- V-V- G
P
+RC
-RC
S-
S+
-RC
P
G
+RC
S+
S-
V+ V+V+
+S
+S
-S
-S
-RC
-RC
+RC
+RC
V+ V-
MS-75
MS-150
V+ V-
LOAD
M
M
ML
ML
G
G
CS
CS
-S
-S
+S
+S
-RC
-RC
+RC
+RC
G
G
ML
ML
M
M
CS
CS
+RC
+RC
-RC
-RC
-S
-S
+S
+S
Figure 3-6
(3)Connecting an additional 100K potentiometer to PIN CN7-6, PIN CN7-7 and PIN CN7-8 will provide an adjustment for theΩ
output voltage in a range of -5% to +5% of the rated voltage (ex: -3%, +2.5% and etc.)
Note The remote margin V program function cannot be used when units are connected in parallel:/- .
CN7-8
CN7-7
CN7-6
V-
V+
CN7
CN7
MS-210
MS-210
V-
LOAD
M
M
ML
ML
G
G
CS
CS
-S
-S
+S
+S
-RC
-RC
+RC
+RC
V+

8
Figure 4-2 Mounting alternatives
Figure 4-3 Mounting screw
Chassis of Customer's system
Screw M4
Hold rack
CN4
TOP
L=6mm max.
P.S.U. Case
CN4
TOP
CN4 TOP CN4
◎This is a power supply with built-in DC fan and please make sure that the ventilation is not blocked. It is suggested that there should
be no barriers within 10cm of the ventilating holes.
◎The power supply unit should be mounted on a holding rack for extra support as shown in Figure 4-2.
◎In order to maintain a safe isolation distance from internal components, please use screws with length less than 6mm measured
from the case as shown in Figure 4-3.
Figure 4-1 System assembly diagram
EMI Board
Bottom
SLOT5
SLOT1
Left
Right
Output Module
FAN
PFC Board
Label
Cover
4.2 Installation Method
4.1 Requirement for Assembly
4.Notes On Operation
◎The assembly diagram of the PFC front-end and output modules is shown in Figure 4-1.
◎Based on safety considerations, the assembly task should be executed in factories certified by the safety organizations and
should be authorized by MEAN WELL in advance as well.

9
AMBIENT TEMPERATURE ( )℃
RATED POWER (%)
-2001020304050
20
40
50
60
80
100
Figure 4-4 Output derating curves for Modular Series
INPUT VOLTAGE (V) 60Hz
100
90
80
85
70
60
RATED POWER (%)
60 70 (HORIZONTAL)
85 90 100 120 140 160 180 200 220 240 264
◎The Modular Series consists of PFC front-end and output modules. The electrical specification of each output module should be
carefully checked before operating and the total output power of all modules that is actually used should be less than the rated
power of its PFC front-end.
◎Output load derating is required for proper operation in high ambient temperature or at low AC input. Please refer to the output derating
curves of MP450, MP650, and MP1K0 shown in Figure 4-4.
4.3 Derating
Series Connection Accessory
FAS 001-
(- :For 1 slot modules
-/ , - )MS 75 150 MD 100
FAS 002-
(- :For 2 slot modules
-)MS 300
FAS 003-
(- :For 1 slot modules
-)MS 210
FAS 004-
(- :For 2 slot modules
-)MS 360
5.1 Series Connection Accessory
5.Series Parallel Connection Accessory/
Parallel Connection Accessory
FAP 001-
()For MS-300, 2 units
FAP 005-
()For MS-210, 4 units
FAP 002-
()For MS-300, 3 units
FAP 006-
()For MS-210, 5 units
FAP 003-
()For MS-210, 2 units
FAP 007-
()For MS-360, 2 units
FAP 004-
()For MS-210, 3 units
FAP 008-
()For MS-360, 3 units
5.2 Parallel Connection Accessory

6.Specification
10
6.1 Front End
■1 SLOT Single Output (150W):MS-150
6.2 Output Module
OUTPUT
(MS-150)
DC VOLTAGE
OUTPUT VOLTAGE CODE MS-150A
2V 3.3V 5V 7.5V 12V 15V 18V 24V 27V 33V 48V
25A 25A 25A 18A 13A 10A 8.5A 6.5A 5.8A 4.7A 3.2A
0 ~ 25A 0 ~ 25A 0 ~ 25A 0 ~ 18A 0 ~ 13A 0 ~ 10A 0 ~ 8.5A 0 ~ 6.5A 0 ~ 5.8A 0 ~ 4.7A 0 ~ 3.2A
30A 30A 30A 20.7A 15A 11.5A 9.8A 7.5A 6.7A 5.4A 3.68A
50W 82.5W 125W 135W 156W 150W 153W 156W 156.6W 155.1W 153.6W
50mVp-p 80mVp-p 80mVp-p 100mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 250mVp-p 250mVp-p
1.6 ~ 2.6V 2.6 ~ 4V 4 ~ 6V 6 ~ 9V 9 ~ 13.2V
13.2 ~ 16.8V 16.8 ~ 20V 20 ~ 26.4V 25 ~ 31V 30 ~ 40V 40 ~ 53V
±3.0% ±2.0% ±2.0% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0%
±0.5% ±0.5% ±0.5% ±0.5% ±0.3% ±0.3% ±0.3% ±0.2% ±0.2% ±0.2% ±0.2%
±2.0% ±1.0% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
MS-150B MS-150C MS-150D MS-150E MS-150F MS-150G MS-150H MS-150I MS-150J MS-150K
1500ms, 50ms, 20ms at full load
RATED CURRENT
CURRENT RANGE
PEAK LOAD Note.4
RATED POWER
RIPPLE & NOISE (max.) Note.2
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
OVER LOAD
OVER VOLTAGE
PROTECTION
121 ~ 150% rated output power 116 ~ 150% rated output power
2.7 ~ 4V 4.1 ~ 5V 6.1 ~ 7.5V
9.1 ~ 11.2V 13.3 ~ 18V 16.9 ~ 22V 20.1 ~ 26V 26.5 ~ 35V 31.1 ~ 39V 40.1 ~ 48V 53.1 ~ 60V
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Constant current limiting, recovers automatically after fault condition is removed
REMOTE INHIBIT CONTROL RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
FUNCTION
PFC-450 PFC-650 PFC-1000
MODEL
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY Note.1
AC CURRENT
INPUT
INRUSH CURRENT
LEAKAGE CURRENT
85 ~ 264VAC 120 ~370VDC
47 ~ 63Hz
PF>0.95/230VAC PF>0.98/115VAC at full load
82.5% typ. 84% typ. 84% typ.
9A/115VAC 4.5A/230VAC
25A/115VAC 40A/230VAC
6.3A/115VAC 3.2A/230VAC
30A/115VAC 50A/230VAC 20A/115VAC 40A/230VAC
13.5A/115VAC 6.7A/230VAC
<1.5mA/240VAC
650W max. 1000W max.
REMOTE CONTROL
AUXILIARY POWER(AUX)
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
FUNCTION
UL62368-1, TUV BS EN/EN62368-1 EAC TP TC 004 approved ,
-20 ~ +70 (Refer to "Derating Curve")℃
20 ~ 90% RH non-condensing
RC+/RC-: 0 ~ 0.8V or Short, Power ON RC+/RC-: 4 ~ 12V or Open, Power OFF
[email protected](only for Remote ON/OFF Control)
-40 ~ +85 , 10 ~ 95% RH non-condensing℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ENVIRONMENT
SAFETY &
OUTPUT 450W max.TOTAL OUTPUT POWER
PROTECTION
FAN ALARM
OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down
Output shutdown when FAN is malfunction
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
EMC
(Note 5)
Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
EMC EMISSION
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55024, BS EN/EN61000-6-1, light industry level, criteria A, EAC TP TC 020
EMC IMMUNITY
OTHERS DIMENSION
PACKING
254*127*63.5mm (L*W*H) 278*127*63.5mm (L*W*H) 278*177.8*63.5mm (L*W*H)
1.8Kg(typ.); 6pcs / 11.8Kg / 1.25CUFT 2.16Kg(typ.); 6pcs / 14Kg / 1.34CUFT 3Kg(typ.); 6pcs /19Kg / 1.74CUFT

11
OUTPUT
(MS-300)
OUTPUT
(MS-360)
DC VOLTAGE
DC VOLTAGE
OUTPUT VOLTAGE CODE
OUTPUT VOLTAGE CODE
1500ms, 50ms, 20ms at full load
1500ms, 50ms, 20ms at full load
■2 SLOT Single output (300W) MS-300
■2 SLOT Single output (360W) MS-360
RATED CURRENT
RATED CURRENT
CURRENT RANGE
CURRENT RANGE
PEAK LOAD Note.4
PEAK LOAD Note.4
RATED POWER
RATED POWER
RIPPLE & NOISE (max.) Note.2
RIPPLE & NOISE (max.) Note.2
VOLTAGE ADJ. RANGE
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LINE REGULATION
LOAD REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
SETUP, RISE, HOLD UP TIME
OVERLOAD
OVERLOAD
OVER VOLTAGE
OVER VOLTAGE
PROTECTION
PROTECTION
116 ~ 150% rated output power
116 ~ 150% rated output power
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Constant current limiting, recovers automatically after fault condition is removed
OUTPUT
(MS-210)
DC VOLTAGE
OUTPUT VOLTAGE CODE
MS-210-1A MS-210-1B MS-210-1C MS-210-1D MS-210-1E MS-210-1F MS-210-1G MS-210-1H MS-210-1IMS-210-1J MS-210-1K
MS-300-2A
MS-360-3A
MS-300-2B
MS-360-3B
MS-300-2C
MS-360-3C
MS-300-2D
MS-360-3D
MS-300-2E
MS-360-3E
MS-300-2F
MS-360-3F
MS-300-2G
MS-360-3G
MS-300-2H
MS-360-3H
MS-300-2I
MS-360-3I
MS-300-2J
MS-360-3J
MS-300-2K
MS-360-3K
2V
2V
2V
3.3V
3.3V
3.3V 5V
5V
5V
7.5V
7.5V
7.5V
12V
12V
12V
15V
15V
15V
18V
18V
18V
24V
24V
24V
27V
27V
27V
33V
33V
33V
48V
48V
48V
35A
50A
60A
50A
60A
50A
60A
35A 35A 28A
40A
48A
17.5A
25A
30A
14A
20A
24A
11.6A
16.7A
20A
8.75A
12.5A
15A
7.8A
11.2A
13.4A
6.4A
9.1A
11A
4.4A
6.3A
7.5A
0 ~ 35A
0 ~ 50A
0 ~ 60A
0 ~ 50A
0 ~ 60A
0 ~ 50A
0 ~ 60A
0 ~ 35A 0 ~ 35A 0 ~ 28A
0 ~ 40A
0 ~ 48A
0 ~ 17.5A
0 ~ 25A
0 ~ 30A
0 ~ 14A
0 ~ 20A
0 ~ 24A
0 ~ 11.6A
0 ~ 16.7A
0 ~ 20A
0 ~ 8.75A
0 ~ 12.5A
0 ~ 15A
0 ~ 7.8A
0 ~ 11.2A
0 ~ 13.4A
0 ~ 6.4A
0 ~ 9.1A
0 ~ 11A
0 ~ 4.4A
0 ~ 6.3A
0 ~ 7.5A
38.5A
57.5A
69A
57.5A
69A
57.5A
69A
38.5A 38.5A 32.2A
46A
55.2A
20.1A
29A
34.5A
16.1A
23A
27.6A
13.4A
19.2A
23A
10.1A
14.4A
17.3A
9A
12.9A
15.5A
7.4A
10.5A
12.7A
5.1A
7.2A
8.7A
70W
100W
120W
165W
198W
115.5W 175W
250W
300W
210W
300W
360W
210W
300W
360W
210W
300W
360W
208.8W
300.6W
360W
210W
300W
360W
210.6W
302.4W
361.8W
211.2W
300.3W
363W
211.2W
302.4W
360W
50mVp-p
80mVp-p
80mVp-p
80mVp-p
100mVp-p
80mVp-p 80mVp-p
80mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
200mVp-p
200mVp-p
250mVp-p
250mVp-p
250mVp-p
250mVp-p
300mVp-p
300mVp-p
1.6 ~ 2.6V
1.6 ~ 2.6V
1.6 ~ 2.6V
2.6 ~ 4V
2.6 ~ 4V
2.6 ~ 4V 4 ~ 6V
4 ~ 6V
4 ~ 6V
6 ~ 9V
6 ~ 9V
6 ~ 9V
9 ~ 13.2V
9 ~ 13.2V
9 ~ 13.2V
13.2 ~ 16.8V
13.2 ~ 16.8V
13.2 ~ 16.8V
16.8 ~ 20V
16.8 ~ 20V
16.8 ~ 20V
20 ~ 26.4V
20 ~ 26.4V
20 ~ 26.4V
25 ~ 31V
25 ~ 31V
25 ~ 31V
30 ~ 40V
30 ~ 40V
30 ~ 40V
40 ~ 53V
40 ~ 53V
40 ~ 53V
±3.0%
±3.0%
±3.0%
±2.0%
±2.0%
±2.0% ±2.0%
±2.0%
±2.0%
±2.0%
±2.0%
±2.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5% ±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.3%
±0.3%
±0.3%
±0.3%
±0.3%
±0.3%
±0.3%
±0.3%
±0.3%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±0.2%
±2.0%
±2.0%
±2.0%
±1.5% ±1.0%
±1.0%
±1.0%
±1.0%
±1.5%
±1.0%
±1.0%
±1.0%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±0.5% ±0.5% ±0.5%
1500ms, 50ms, 20ms at full load
■1 SLOT Single output (210W) MS-210
RATED CURRENT
CURRENT RANGE
PEAK LOAD Note.4
RATED POWER
RIPPLE & NOISE (max.) Note.2
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
OVERLOAD
OVER VOLTAGE
PROTECTION
110 ~ 135% rated output power 116 ~ 150% rated output power
2.7 ~ 4V
3 ~ 4V
3 ~ 4V
4.1 ~ 5V
4.1 ~ 5V
4.1 ~ 5V
6.1 ~ 7.5V
6.1 ~ 7.5V
6.1 ~ 7.5V
9.1 ~ 11.2V
9.1 ~ 11.2V
9.1 ~ 11.2V
13.3 ~ 18V
13.3 ~ 18V
13.3 ~ 18V
16.9 ~ 22V
16.9 ~ 22V
16.9 ~ 22V
20.1 ~ 26V
20.1 ~ 26V
20.1 ~ 26V
26.5 ~ 35V
26.5 ~ 35V
26.5 ~ 35V
31.1 ~ 39V
31.1 ~ 39V
31.1 ~ 39V
40.1 ~ 48V
40.1 ~ 48V
40.1 ~ 48V
53.1 ~ 60V
53.1 ~ 60V
53.1 ~ 60V
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Constant current limiting, recovers automatically after fault condition is removed
REMOTE INHIBIT CONTROL
REMOTE INHIBIT CONTROL
RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
FUNCTION
FUNCTION
Protection type : Shut down o/p voltage, re-power on to recover
REMOTE INHIBIT CONTROL RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
FUNCTION

12
24V
5A 3.2A
3.7A
OUTPUT
(MD-100)
DC VOLTAGE
OUTPUT VOLTAGE CODE MD-100R MD-100S MD-100T MD-100U MD-100V MD-100X
5V 5V 5V 15V5V 12V 15V 24V 15V
10A 10A 10A 4A8A 4.2A 3.4A 2.5A 2.7A
2 ~ 10A 2 ~ 10A 2 ~ 10A 0 ~ 4.7A
1 ~ 4.7A 0 ~ 8A 0 ~ 5.8A 0.5 ~ 3A 0 ~ 4.7A
90W 100.4W 101W 100W 100.5W
100mVp-p 150mVp-p 150mVp-p 200mVp-p 150mVp-p100mVp-p 100mVp-p 100mVp-p 150mVp-p
4.75 ~ 5.5V 4.75 ~ 5.5V 4.75 ~ 5.5V 4.75 ~ 5.5V 14.2 ~ 16.5V 14.2 ~ 16.5V 11.4 ~ 13.2V 14.2 ~ 16.5V 22.8 ~ 26.4V 4.75 ~ 5.5V
±3.0%±3.0% ±3.0% ±3.0% ±3.0%±3.0% ±3.0% ±3.0% ±3.0%±2.0%
±1.0%±1.0% ±1.0% ±1.0% ±1.0%±1.0% ±1.0% ±1.0% ±1.0%±0.5%
±2.0%±2.0% ±2.0% ±2.0% ±2.0%±2.0% ±2.0% ±2.0% ±2.0%±1.0%
1500ms, 50ms, 20ms at full load
■1 SLOT Isolated Dual output (100W) MD-100
RATED CURRENT
CURRENT RANGE
RATED POWER Note.6
RIPPLE & NOISE (max.) Note.2
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
105 ~ 150% rated output power
5V
8A
0 ~ 10A
100mVp-p
12V
3.4A
0 ~ 4.7A
100.8W
120mVp-p
11.4 ~ 13.2V
±3.0%
±2.0%
±1.0%
±0.5%
±2.0%
±1.0%
24V
2.5A
0.6 ~ 3A
240mVp-p
22.8 ~ 26.4V
12V 12V
5A 3.4A
1 ~ 5A 0 ~ 5.8A
100.8W
120mVp-p 120mVp-p
11.4~ 13.2V 11.4~ 13.2V
±3.0%±2.0%
±1.0%±0.5%
±2.0%±1.0%
MD-100W
OVERLOAD
OVER VOLTAGE
PROTECTION
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Shut down o/p voltage, re-power on to recover
5.6 ~ 7.2V 5.6 ~ 7.2V 5.6 ~ 7.2V 5.6 ~ 7.2V 13.3 ~ 17V 16.6 ~ 22V 16.6 ~ 22V 16.6 ~ 22V 26.5 ~ 34V 5.6 ~ 7.2V 13.3 ~ 17V 26.5 ~ 34V 13.3 ~ 17V 13.3 ~ 17V
REMOTE INHIBIT CONTROL RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
FUNCTION
±0.5% ±0.5% ±0.3% ±0.3% ±0.2% ±0.2%
±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5%
1500ms, 50ms, 20ms at full load
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
OVERLOAD
OVER VOLTAGE
PROTECTION
116 ~ 150% rated output power
Protection type : Shut down o/p voltage, re-power on to recover
4.1 ~ 5V 6.1 ~ 7.5V 13.3 ~ 18V 16.9 ~ 22V 26.5 ~ 35V 53.1 ~ 60V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
REMOTE INHIBIT CONTROL RC+/RC-: 0 ~ 0.8V or OPEN, POWER ON RC+/RC-: 4 ~ 12V POWER OFF
FUNCTION
OUTPUT
(MS-75)
DC VOLTAGE
OUTPUT VOLTAGE CODE
3.3V 5V 12V 15V 48V
15A 15A 6.3A 1.6A
0 ~ 15A 0 ~ 15A 0 ~ 6.3A 0 ~ 5A 0 ~ 3.2A 0 ~ 1.6A
17.3A 17.3A 7.3A 5.8A 1.8A
49.5W 75W 75.6W 75W 76.8W 76.8W
80mVp-p 80mVp-p 150mVp-p 150mVp-p 150mVp-p 250mVp-p
2.6 ~ 4V 4 ~ 6V 9 ~ 13.2V
13.2 ~ 16.8V 20 ~ 26.4V 40 ~ 53V
±2.0% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0%
MS-75L MS-75M MS-75N MS-75O MS-75P MS-75Q
■1 SLOT Single output (75W) MS-75
RATED CURRENT
CURRENT RANGE
PEAK LOAD Note.4
RATED POWER
RIPPLE & NOISE (max.) Note.2
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3
NOTE 1. MP450:The value changed by installing different output odules. The efficiency in specification eans output odules are co posed by following odules.
5V(Voltage code C)*1, 12V(Voltage code E)*1, 24V(Voltage code H)*1, 5V(Voltage code M)*1.
MP650:The value changed by installing different output odules. The efficiency in specification eans output odules are co posed by following odules.
5V(Voltage code C)*2, 12V(Voltage code E)*1, 24V(Voltage code H)*2.
MP1K0:The value changed by installing different output odules. The efficiency in specification eans output odules are co posed by following odules.
5V(Voltage code C)*2, 12V(Voltage code E)*2, 24V(Voltage code H)*3.
The hold-up ti e of above co bination is 20 s(typ.)
2. Ripple & noise are easured at 20MHz of bandwidth by using a 12" twisted pair-wire ter inated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. 35% Duty cycle axi u within every 10 seconds. Average output power should not exceed the rated power.
5. The power supply is considered a co ponent which will be installed into a final equip ent. All the EMC tests are been executed by ounting the unit on
a * etal plate with 1 of thickness. The final equip ent ust be re-confir ed that it still eets EMC directives.720 360 For guidance on how to
perfor these EMC tests, please refer to EMI testing of co ponent power supplies. (as available on http://www. eanwell.co )
6. If the output voltage adjust to higher level, the rated current should be derated to eet the total rated power for both outputs(For MD-100 only).
7.The a bient te perature derating of 3.5 /1000 with fanless odels and of 5 /1000 with fan odels for operating altitude higher than 2000 (6500ft).℃℃