Sega House Of The Dead 3 DELUXE User manual

420-6742-01UK REV 0
SERVICE MANUAL
DELUXE TYPE
Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein.
After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order
to be able to refer to it whenever necessary.
Manufactured in the UK by

i
CONTENTS
1. BEFORE USING THIS PRODUCT........................................................................................................1
1.1. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION..2
2. INTRODUCTION TO THIS SERVICE MANUAL ...................................................................................4
3. INSTALLATION AND SERVICE INSTRUCTIONS................................................................................5
3.1. HANDLING AND INSTALLATION PRECAUTIONS ..........................................................................5
3.2. COIN HANDLING...............................................................................................................................5
3.3. NAME OF PARTS ..............................................................................................................................6
3.4. ACCESSORIES .................................................................................................................................7
3.5. SHIPPING THE GAME BOARD.........................................................................................................8
3.6. SHIPPING THE MEDIA BOARD......................................................................................................10
3.7. SHIPPING THE GD-ROM DRIVE....................................................................................................11
3.8. ASSEMBLY INSTRUCTIONS ..........................................................................................................12
3.8.1. ASSEMBLE THE MACHINE .....................................................................................................13
3.8.1.1. ASSEMBLE THE PTV .......................................................................................................13
3.8.1.2. ATTACH THE GUARD RAILS...........................................................................................14
3.8.1.3. ATTACH GUN PANELS TO GUN CABINET ....................................................................14
3.8.1.4. ATTACH THE GUN CABINET ..........................................................................................15
3.8.1.5. FIT THE BILLBOARD TO THE PTV..................................................................................16
3.8.2. LEG-LEVELLING PROCEDURE ..............................................................................................17
3.8.3. COIN HANDLING INSTALLATION...........................................................................................18
3.8.3.1. WIRING CONNECTIONS..................................................................................................19
3.8.4. CONNECTION TO THE POWER SUPPLY..............................................................................20
3.8.5. ADJACENT CONTROL INTERFERENCE PREVENTION.......................................................21
3.9. ASSEMBLY CHECK.........................................................................................................................22
3.9.1. MEMORY TEST........................................................................................................................22
3.9.2. C.R.T. TEST .............................................................................................................................23
3.9.3. INPUT TEST .............................................................................................................................24
3.9.4. OUTPUT TEST .........................................................................................................................24
3.9.5. GUN ADJUSTMENT.................................................................................................................25
3.10. MOVING THE MACHINE .............................................................................................................26
3.11. FUSES..........................................................................................................................................27
3.12. REPLACEMENT OF FLUORESCENT LAMP AND OTHER LAMPS...........................................28
3.12.1. FLUORESCENT LAMP REPLACEMENT.............................................................................28
3.12.2. LAMP REPLACEMENT.........................................................................................................29
3.13. TROUBLESHOOTING .................................................................................................................30
3.14. CONTROLLER UNIT (SHOTGUN) ..............................................................................................31
3.15. GAMEBOARD ..............................................................................................................................34
3.15.1. REMOVING THE BOARD.....................................................................................................34
3.15.2. REMOVING THE GD-ROM DRIVE.......................................................................................36
3.16. COMPOSITION OF THE GAME BOARD ....................................................................................37
3.17. PERIODIC CHECK AND INSPECTION .......................................................................................38
4. HOW TO PLAY....................................................................................................................................39
4.1. GAME CONTENTS..........................................................................................................................40
4.1.1. GAME OUTLINE.......................................................................................................................40
4.1.2. ITEMS .......................................................................................................................................43
4.1.3. PLAY HINTS .............................................................................................................................43
5. MAINTENANCE INSTRUCTIONS.......................................................................................................44
5.1. EXPLANATION OF TEST AND DATA DISPLAY ............................................................................44
5.1.1. VTS ASSEMBLY.......................................................................................................................46
5.2. SYSTEM TEST MENU MODE.........................................................................................................47
5.2.1. MEDIA BOARD TEST...............................................................................................................48
5.2.2. SYSTEM INFORMATION .........................................................................................................49
5.2.3. JVS TEST .................................................................................................................................50
5.2.4. INPUT TEST Screen.................................................................................................................51
5.2.5. SOUND TEST...........................................................................................................................52
5.2.6. C.R.T. TEST .............................................................................................................................53
5.2.7. COIN ASSIGNMENTS..............................................................................................................54
5.2.8. CLOCK SETTING .....................................................................................................................57
5.2.9. NETWORK SETTING (CORE).................................................................................................58
5.2.10. NETWORK SETTING (MEDIA) ............................................................................................59
5.3. GAME TEST MODE.........................................................................................................................63
5.3.1. INPUT TEST .............................................................................................................................64

ii
5.3.2. OUTPUT TEST .........................................................................................................................65
5.3.3. GAME ASSIGNMENTS ............................................................................................................66
5.3.4. GUN SETTING .........................................................................................................................67
5.3.4.1. GUN MARK CHECK..........................................................................................................68
5.3.4.2. PLAYER1 GUN ADJUSTMENT/PLAYER2 GUN ADJUSTMENT .....................................69
5.3.4.3. PLAYER1 GUN DEFAULT ADJUSTMENT/PLAYER2 GUN DEFAULT ADJUSTMENT ..72
5.3.5. BOOKKEEPING........................................................................................................................73
5.3.6. BACKUP DATA CLEAR............................................................................................................75
6. COIN MECH INSTALLATION AND CREDIT BOARD SET UP...........................................................76
6.1. INTRODUCTION..............................................................................................................................76
6.1.1. PRICE OF PLAY SETTINGS UK .............................................................................................78
6.1.2. PRICE OF PLAY SETTINGS EURO ........................................................................................79
6.1.3. PRICE OF PLAY SETTINGS Austria-Czech-Denmark-Norway-Israel-France2 ......................80
7. DESIGN RELATED PARTS.................................................................................................................81
8. PARTS LIST ........................................................................................................................................82
8.1. HDT-0000UK - TOP ASSY HOUSE OF THE DEAD3 DX ...............................................................82
8.2. HDT-0500UK - ASSY PTV ...............................................................................................................83
8.3. HDT-0520UK - ASSY BILLBOARD DX............................................................................................84
8.4. SPX-0530UK ASSY MASK .............................................................................................................85
8.5. HDT-1000UK ASSY PTV CABI DX.................................................................................................86
8.6. HDT-1060UK ASSY LID UPPER ....................................................................................................88
8.7. HDT-1070UK ASSY LID LOWER ....................................................................................................89
8.8. HDT-1100UK ASSY CONTROLLER CABINET ...............................................................................90
8.9. HDT-1150UK ASSY FENCE L .........................................................................................................92
8.10. HDT-1160UK ASSY FENCE R....................................................................................................93
8.11. HDT-2000UK ASSY CTRL PANEL DX ........................................................................................94
8.12. HDT-2100 CONTROL UNIT .........................................................................................................95
8.13. SENSOR UNIT (JPT-2030) ..........................................................................................................96
8.14. HDT-2180UK ASSY GUN HOLDER W/TETHER L .....................................................................97
8.15. HDT-2190UK ASSY GUN HOLDER W/TETHER R.....................................................................98
8.16. HDT-4000UK ASSY MAIN BD DX................................................................................................99
8.17. HDT-4200UK ASSY PWR SPLY...............................................................................................101
8.18. HDT-INST-DX ASSY INST KIT HDT DX....................................................................................102
8.19. HOD-1020UK ASSY AC UNIT....................................................................................................103
8.20. HOD-1070UK ASSY SPEAKER .................................................................................................104
8.21. HDT-1530UK ASSY FAN UNIT DC UK.....................................................................................104
9. APPENDIX A - ELECTRICAL SCHEMATIC......................................................................................105
9.1. WIRE COLOURS ...........................................................................................................................105
9.2. ELECTRICAL SCHEMATIC ...........................................................................................................105

1
1. BEFORE USING THIS PRODUCT
To ensure the safe usage, be sure to read the following before using the product. The following instructions are
intended for the use of QUALIFIED SERVICE PERSONNEL ONLY.
If any activity is carried out on the product, this should be done only after carefully reading and sufficiently
understanding the instructions.
Only qualified service personnel should carry out maintenance on the product.
Depending on the potential risk, terms such as” WARNING!” “CAUTION” and “IMPORTANT!” are used where an
explanation is given that requires special attention. SEGA is not responsible for injury or damage caused by use in a
manner contrary to the instructions given in this document.
In order to prevent accidents warning stickers and printed instructions are applied in the places where a potentially
hazardous situation relating to the product could arise. Be sure to comply with these warnings.
Indicates that mishandling the product by disregarding this warning will cause a potentially
hazardous situation that can result in death or serious injury.
Indicates that mishandling the product by disregarding this caution will cause a potentially
hazardous situation that can result in personal injury and or material damage.
This is cautionary information that should be complied with when handling the product.
Indicates that mishandling the product by disregarding this will cause a potentially hazardous
situation that may not result in personal injury but could damage the product.
Be sure to turn off the power and disconnect from the mains supply before working on the machine.
Ensure that the correct fuses are fitted to the machine. Details of these are enclosed in the Service Manual.
Ensure that only qualified Service Engineers perform any maintenance work on the machine.
Specification changes, removal of equipment, conversion and/or additions not designated by SEGA are not permitted
and will invalidate this product’s CE conformity.
Warning labels or safety covers for personal protection etc, are component parts of the product. A potential hazard will
be created if the machine is operated while any parts have been removed. Do not operate the product if any doors, lids
or protective covers become damaged or lost. SEGA is not liable in any whatsoever for any injury and/or damage
caused by specification changes not designated by SEGA.
Before installing the product, check for the Electrical Specification Sticker, SEGA products have a sticker on which the
electrical specifications are detailed. Ensure that the product is compatible with the power supply voltage and
frequency requirements of the location in which the machine is to be installed.
Install and operate the machine only in places where appropriate lighting is available, allowing warning stickers to be
clearly read.
To ensure maximum safety for customers and operators, stickers and printed instructions describing potentially
hazardous situations are applied to potentially hazardous locations. Ensure that the product’s operating location has
sufficient lighting to allow any warnings to be read. If any sticker or printed warning is removed or defaced, do not
operate the machine until an identical item has replaced it.
Exercise great care when handling the monitor (applies only to product with monitor). Some of the monitor (TV) parts
are subject to high-tension voltage. Even after turning the power off some components are liable to high-tension
voltage. Only qualified service engineers should perform monitor repair and replacement.
In cases where commercially available monitors and printers are used, only the items relating to this product are
contained in this manual. Some commercially available equipment will have functions and reactions not referred to in
this manual. This manual should be read in conjunction with the specific manufacturer’s manual for such equipment.
Descriptions contained herein may be subject to change without prior notification.
The contents described herein are fully prepared with due care. However, should any question arise or errors be found
please contact SEGA AMUSEMENTS EUROPE LTD.
Descriptions contained herein may be subject to change without prior notification.

2
The contents described herein are fully prepared with due care. However, should any question arise or
errors be found please contact SEGA.
1.1. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT
TO THE LOCATION
· Only QUALIFIED SERVICE PERSONNEL should carry out inspection.
Normally, at the time of shipment, SEGA products are in a state to allowing usage immediately after
transporting to the location. Nevertheless, an irregular situation may arise during transportation preventing
this. Before turning on the power, check the following points to ensure that the product has been transported
safely.
· Are then any dented parts or defects (cuts, etc.) on the external surfaces of the product.?
· Are castors and leg adjusters present and undamaged?
· Do the power supply voltage and frequency requirements meet with the local supply?
· Are all wiring connectors correctly and securely connected? Unless connected in the correct direction,
connector connections cannot be made successfully. Do not insert connectors forcibly.
· Are all IC’s of each IC BD firmly inserted?
· Does the power cord have any cuts or dents?
· Do fuses meet the specified rating?
· Are such units such as monitors, control equipment, IC BD, etc. firmly secured?
· Are all earth wires connected?
· Are all accessories available?
· Can all doors and lids be opened with the accessory keys and/or tools?

3
CONCERNING THE STICKER DISPLAY CONCERNING WARNING STICKERS
SEGA product has stickers describing the product
manufacture number (Serial Number) and
electrical specification. If you require service
assistance you will require the Serial Number.
Identical machines may have different parts fitted
internally. Only by quoting the Serial Number will
the correct parts be identified.
SEGA product has warning displays on
stickers, labels or printed instructions
adhered/attached to or incorporated in the
places where hazardous situations can arise.
The warning displays are intended for the
accident prevention of customers and service
personnel.
SPECIFICATIONS
Installation Space (cm): 114 x 164.6
Height (cm): 198
Weight (kg): 247
Rated Voltage (V.AC): 230/50Hz
Rated Current: 2A
Operating Temperature Range: 5-30ºC
Note: Descriptions in this manual are subject to change without prior notice.

4
2. INTRODUCTION TO THIS SERVICE MANUAL
SEGA ENTERPRISES LTD. supported by its experience in electronic high technology of VLSI’s,
microprocessors etc. and with a wealth of experience, has for more than 30 years been supplying various
innovative and popular games to the world market. This Service Manual is intended to provide detailed
descriptions together with all the necessary information covering the general operation of electronic
assemblies, electro-mechanicals, servicing controls, spare parts, etc. as regards this new SEGA product.
This manual is intended for those who have knowledge of electricity and technical expertise especially in
IC’s, CRT’s, microprocessors etc. Carefully read this manual to acquire sufficient knowledge before
working on the machine. Should there be any malfunction, non-technical personnel should under no
circumstances touch the internal systems. Should such a situation arise contact our head office.
SEGA AMUSEMENTS EUROPE LTD./ SEGA SERVICE CENTRE
Suite 3a
Oaks House
12 - 22 West Street
Epsom
Surrey
United Kingdom
KT18 7RG

5
3. INSTALLATION AND SERVICE INSTRUCTIONS
· Only QUALIFIED SERVICE PERSONNEL should carry out installation and
commissioning.
3.1. HANDLING AND INSTALLATION PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure
that the player can enjoy the game safely.
The game must NOT be installed under the following conditions:
· Outside, the game is designed for indoor use only.
· In areas directly exposed to sunlight, high humidity, dust, excessive heat or extreme cold.
· In locations that would present an obstacle in the case of an emergency i.e. near fire equipment or
emergency exits.
· On unstable surfaces or surfaces subject to vibration.
· Where liquids, other than routine cleaning, may come into contact with the game.
Important:
· Only Qualified Service Personnel should install this machine.
· Be sure to switch the supply power OFF and remove the mains supply plug from the machine before any
work is carried out on the machine.
· Do not attempt to repair the PCB’s (Printed Circuit Boards) yourself. This will void the warranty. The
PCB’s contain static sensitive devices that could be damaged.
· Always return a faulty part to your distributor with adequate packaging and protection.
· When removing the plug from the mains always grasp the plug not the cable.
· Do not use a fuse that does not meet the specified rating.
· Make sure all connections are secure before applying power.
· Ensure that the mains lead is not damaged. If the mains lead is damaged in any
way there could be a danger of electric shock or a fire hazard.
· Ensure that the power supply is fitted with circuit protection. Using the power
supply without circuit protection is a fire hazard.
3.2. COIN HANDLING
Standard Sega machines are fitted with a SR3 coin mechanism, however, as a service to our customers
Sega machines can be supplied with no coin mechanism or door allowing the customer to fit a coin handling
option from the approved list. Fit only the coin handling arrangements detailed below and follow the
instructions provided in section 3.8. Failure to fit the coin handling options detailed or failure to follow the
installation instructions will render the machine, under the CE marking directive, void.
Approved coin handling options:
· Coin controls SR3
· Generic mechanical
· Mars (MS111B1 and ME115)
· SECI RM4-G20

6
3.3. NAME OF PARTS
Width (cm) Length (cm) Height (cm) Weight (kg)
PTV 114 53 158 91
BILLBOARD 114 40 40 19
MAIN CABI DX 114 96.8 93.9 87
GUN CABI 54.8 101 98.7 40
When Assembled 114 164.6 198 247

7
3.4. ACCESSORIES
The machine is supplied with an installation kit. Please ensure the following parts are supplied:
Item Component Part Qty. Description
1 HDT-0520UK 1 ASSY BILLBOARD DX
2 HOD-0006 2 L BRKT
4 440-CS0186UK 1 STICKER C EPILEPSY MULTI
6 HDT-2180UK 1 ASSY GUN HOLDER W/TETHER L
7 HDT-2190UK 1 ASSY GUN HOLDER W/TETHER R
22 PK0318 1 CARTON BOX INST KIT HDT DX
23 SAECE-XXX 1 DECLARATION OF CONFORMITY
24 HDT-2002UK 1 INST PLATE HDT DX MULTI
101 290094 0.08 WRAP BUBBLE (SM) 600MM X 100M
201 030-000850-SB 4 M8X50 BLT W/S BLK
202 030-000830-SB 8 M8X30 BLT W/S BLK
203 029-F00625-0B 4 M6X25 SKT CSK BLK
205 000-T00420-0B 4 M4X20 MSCR TH BLK
206 068-441616-0B 4 M4 WSHR 16OD FLT BLK
207 030-000840-SB 8 M8X40 BLT W/S BLK
208 068-852216-0B 24 M8 WSHR 22OD FLT BLK
209 030-000860-0B 4 M8X60 BLT BLK
401 420-6620UK 1 SERVICE MANUAL GD ROM SYSTEM
402 OS1019 2 SELF SEAL BAG 9X12.3/4
403 420-6742-01UK 1 SERVICE MANUAL HDT DX
405 390-5160 1 LAMP WG B TYPE 6V 3W (C2R)
406 509-5080 2 SW MICRO TYPE (SS-5GL2)
413 514-5078-5000 1 FUSE 5X20 CERAMIC SB 5000mA

8
3.5. SHIPPING THE GAME BOARD
Replacement or repair of the Game Board (Chihiro) for this product should be undertaken at
the appropriate repair centre. Be sure to follow the specifications below when requesting
repairs/sending the board to the repair centre. Not following the specifications may result in
the board not being accepted or in extra charges being made.
· Put the game board in the carton box as is. Do not carry out any disassembly or part
removal other than that specified.
· Follow the procedure and instructions regarding direction below when placing the Game
Board in the carton box.
· When packing the game board with the Media Board attached, do not remove the Key
Chip.
· When packing the game board with the Media Board detached, be sure to include the
AVIP Cable.
· When packing, attach the accessory stickers in the specified places on the Game Board
and carton box.
INSTRUCTIONS
1. Wrap the Chihiro Board in a plastic bag.
2. Place it on top of the bottom surface cushioning material. Turn the Filter Board to face the side with
the three honeycomb buffers. Packing it in the opposite direction may cause damage to the Filter
Board.
3. Insert corrugated cardboard into the space between the lateral honeycomb buffers of the bottom
surface cushioning material and stow the AVIP cable inside.
4. Place the Chihiro Board wrapped in the bottom surface cushioning material into the carton box. Use
the handles on the bottom surface cushioning material.
5. Place the upper surface cushioning material on top of the Chihiro Board. Be sure to align it in the
right direction, as it will not fit otherwise.
6. Close the top of the carton box and seal it tightly with adhesive tape.

9

10
3.6. SHIPPING THE MEDIA BOARD
When sending the Media Board for repairs, follow the specifications below and
request repairs or send the Board to your retailer/the repair centre.
Not following the specifications may result in the board not being accepted or in extra
charges being made. Also, mistaken handling can damage or result in loss of parts.
· Be sure to use the special purpose carton box included with this product.
· Do not remove the Key Chip. Send the board with the Key Chip attached.
· Undo the 10 screws holding the Media Board to the Main Board and pack the
Media Board. Do not carry out any disassembly or part removal other than that
specified in this manual.
· Pack the Media Board in the special purpose carton box as shown in the
explanatory diagram.
· The packing material in the carton box has a shock absorbing function. Be sure
to use it when packing. Do not bend or fold the material in a direction other than
that shown on the diagram.
· Do not pack any wires, cables, or screws together with the Board.
· Be sure to attach the special purpose carton box accessory sticker
"843-ããããB."

11
3.7. SHIPPING THE GD-ROM DRIVE
· When returning the GD-ROM DRIVE for repair or replacement, be sure to
package it in the original card transit box - THERE ARE NO USER-
SERVICEABLE PARTS INSIDE.
· Ensure the GD-ROM Disk is removed and the GD-ROM Drive Lid is replaced on
the unit, with fixing screw, before packaging. Also, remove the GD-ROM Drive
Bracket and store with the four screws for reuse.
· Failure to return the GD-ROM DRIVE in this manner may invalidate the warranty.

12
3.8. ASSEMBLY INSTRUCTIONS
· Perform the assembly by following the procedure herein stated. Failure to comply
with the instructions, for example, inserting the plug into an outlet at a stage not
mentioned in this manual can cause an electric shock
· Assembling should be performed as per this manual. Since this is a complex
machine, erroneous assembling can cause damage to the machine, or
malfunction to occur.
· Do not attempt to complete this work alone, a minimum of 2 people are required.
· Only QUALIFIED SERVICE PERSONNEL should carry out assembly.
When carrying out the assembly work, follow the procedure in the following sequence:
STEP 1: ASSEMBLE THE MACHINE
STEP 2: LEG-LEVELLING PROCEDURE
STEP 3: COIN HANDLING INSTALLATION.
STEP 4: CONNECTION TO THE POWER SUPPLY
STEP 5: ASSEMBLY CHECK
Note that the parts contained within the installation kit are required for the assembly work.
· Fit all fixings loosely first as detailed in step 1, then position all components before
finally tightening fixings at step 4.

13
3.8.1. ASSEMBLE THE MACHINE
3.8.1.1.ASSEMBLE THE PTV
1. Place the PTV and PTV Cabinet in roughly their
final position, in close enough proximity to make
the connections shown.
It is imperative that the earth eyes are connected
to the plate at the bottom of the PTV.
2. Lift the PTV forwards onto the PTV Cabinet,
using a minimum of four workers to lift the PTV,
plus a further worker to steady the PTV Cabinet.
Use care during this exercise, as the PTV weighs
in excess of 100kg.
3. Ensure the PTV is correctly seated on the PTV
Cabinet.
(Actual machine may differ slightly from the illustration)

14
3.8.1.2.ATTACH THE GUARD RAILS
1. Remove the guardrails from their packaging.
2. Fit the rails to the gun cabinet as shown using the
M8 bolts and the M4 screws provided.
3.8.1.3. ATTACH GUN PANELS TO GUN CABINET
1. Take off from plates via 4 off M4 X 16mm
security screws.
2. Remove the uppermost M6 Bolts either side of
the coin tower.

15
3. Secure Gun HOLSTERS to Bracket using (4)
M6 x 25 Socket Head Countersink Black Bolts
(Pt No.029-F00625-0B)
[2 per Assy]
4. Refit all removed components / fixings
3.8.1.4.ATTACH THE GUN CABINET
1. After fitting the guard rails to the gun
cabinet fit the gun cabinet to the main
cabinet.
2. Slide the gun cabinet into the hole in
the main cabinet as shown.
3. Fix the gun cabinet in position using
the joint brackets and M8 bolts
provided.
4. Once the cabinet is secure connect
the connectors as shown.
5. Fit the cover in place using the M4x30
screws provided.

16
3.8.1.5. FIT THE BILLBOARD TO THE PTV
1. Fix the billboard to the PTV as shown.
2. Be sure to fit the connector from the billboard to
the PTV. It is imperative that the earth eye is
connected to the top plate of the PTV.
3. Place the billboard onto the PTV and slide it
forward under the catches
4. Fix the billboard in position using the 2 off M5x16
screws provided
When fitting the Billboard, be sure to use three people for safety.

17
3.8.2. LEG-LEVELLING PROCEDURE
· This operation requires 2 people. Ensure that all leg adjusters are in contact with
the floor otherwise the machine may move and cause injury.
· Only QUALIFIED SERVICE PERSONNEL should carry out this operation.
This machine has 4 castors and 8 leg adjusters. When the installation position is decided, unscrew the leg
adjusters so that they raise each castor a minimum of 5mm from the floor. Make sure the machine is level.
1. Move the machine to its final position.
2. Adjust the leg adjusters as shown until the
castors are approximately 5mm off the floor and
the machine is level.
Ensure adequate ventilation is maintained as detailed below