Mercedes-Benz BLU-MBCD User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
BLU-MBCD
QUICK START INSTALLTION GUIDE FOR MERCEDES BENZ WITH CD CHANGER

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and may
require additional steps. We do not accept responsibility for third party labor charges or
modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from the
installation of this product.
•Careless installation and operation can result in equipment damage
Requirement
Mercedes BENZ with ANALOG CD CHANGER
Introduction
With Bluetooth Technology and your Smartphone's voice recognition application (Siri
or Google Now); users can initiate hands-free calls, launch navigation, streaming or
any other application. One button (conveniently installed on the dash) does it all. The
microphone captures your voice commands and allows your phone to make calls and
launch important applications. The BLU-MBCD works in 1994-98 Mercedes Benz with
analog CD changer. Band and does not interfere with normal radio operation.
Notes:
1. A working 6-disc CD changer must be present otherwise this kit does not apply.
2, 1999+ vehicles with digital optical audio CD changer are not compatible.
Installation
Installing this module requires radio removal
Remove radio from dashboard to gain access to connectors. A pair of removal tools
(See Fig. 1) required (sold separately).
Fig. 1
removal tools
this radio does not apply.
1. Slide tools into radio slots (left and right) with straight edge facing away
until detent position. Withdraw radio by pulling tools. See Fig. 2
Click here for more detailed radio removal instructions.

Fig. 2
2. Disconnect 10-pin plug (See Fig. 3) from radio (C) socket (See Fig. 4) and
connect it to harness 10-pin socket in Fig. 5
Fig. 3
Fig. 4
radio sockets
Fig. 5
3. Connect harness 10-pin plug (See Fig. 6) to radio (C) socket vacated in step
2 (See Fig. 4)
Fig. 6
4. Disconnect solid BLACK plug from radio A & Bsockets (See Fig. 4/7)
and connect it to harness matting sockets on power harness (See Fig. 8)
Fig. 7
5. Connect harness 8-pin BROWN plug to the radio (B) socket (See Fig. 4).
6. Connect harness 8-pin BLACK plug to the radio (A) socket (See Fig. 4)

Fig. 8
harness
Fig. 9
connecting diagram
7. Connect harness 16-pin plug (See Fig. 10) to Bluetooth module (See Fig. 11)
Fig. 10
installation harness
Fig. 11
Module
8. Secure/Install microphone to visor or headliner (See Fig. 12 & 13) using visor
clip
Fig. 12
Microphone
Fig. 13
Visor clip
9. Carefully route microphones cable 1/8” plug behind the dash and plug into the
“MIC” jack as seen in Fig. 14
Fig. 14
Module
10. Remove tape backing from control button and secure to dash area within drivers
reach

Fig. 15
Control button
11. Route control button PINK and BLACK wires (See Fig. 16) behind the dash and
mate with (2) matching wires on installation harness (See Fig.10).
Fig. 16
terminals
Pairing and connection
This process is required upon initial install. After initial pairing, the BLU-MBCD will
automatically reconnect with paired device upon entering the vehicle.
1. Turn vehicle ignition to “ON”.
2. Press and hold control button for 2-4 seconds (red/green LED inside
module will begin to flash
3. Access smart device Bluetooth menu settings, and search for new devices.
4. Select “TranzIt BLU HF”. Choose “Connect”
For specific instructions or in case of difficulty, please see “Phone Setup” on
page 4 on the included ISfM2351 manual.
Radio must be in “AUX” or CD changer mode when using the BLU-MBCD.
Warning! Caller ID and text display are not possible in CD mode. Operating
Bluetooth device is by pressing green control button and Voice Recognition
application. Use radio volume button to control playback level

Operation
Phone Calls Incoming call mode (phone ringing)
1) Single press: Answer
2) Press and hold (2 seconds but less than 4 seconds): to reject call
Call mode (during a hands-free call)
1) Single press to End call
2) Press and hold (2 seconds but less than 4 seconds): Toggle privacy/Hands-free
mode
Streaming Music
1) Single press: Next track
2) Press and Hold (2 seconds but less than 4 seconds): Launch VR
3) Press and Hold (more than 4 seconds): Disengage (turn module off)
1. See operating manual Included in Kit for specific steps required to stream
audio or to make/receive calls and for troubleshooting.
2. If successful go ahead and reinstall radio
Congratulations, you’ve just updated your vehicle to support new technology while
preserving the original radio and dash components.
Enjoy!
Frequent Asked Questions
1. My vehicle has the required CD Changer. Do I have to disconnect it for this
kit to work?
NO; The required CD changer remain connected but will no longer play. To retain
CD changer usage purchases our MBCD-HF or A2DIY-MBCD
2. Does the BLU-MBCD work on all Mercedes radios?
NO; This Bluetooth receiver kit works in 1994-98 Mercedes with Becker BE1492,
BE1692, BE2210, BE1350 or Alpine CM2296, CM2396 and a functioning CD
changer. 1999+ use digital CD changers and are not compatible
3. Can I control Smartphone music from radio buttons?
NO; you must continue to use audio device built-in controls or control
button and/or voice commands to operate audio device. Use the radio
volume control button to set playback level.
4. Where is the best place to install the control button?
We found that having the control button placed high on the dash works helped to
keep eyes on the road while performing these functions.
5. Will radio mute when I receive or make a phone call?
This system will mute only if radio is in Bluetooth mode (CD). If in any other
mode (e.g., AM/FM), radio will not mute. In addition, user must switch the radio
to “CD “(Bluetooth Mode) to connect with caller.
6. Why is a second phone not able to pair with Bluetooth receiver?
In order to pair a second phone make sure no other phone is connected. Once
the device is free, it will be ready to pair. To force module into pairing mode
press and hold control button for 2-4 seconds.
Disclaimer
• This product has no affiliation with Porsche, Becker or Apple
• There are no warranties expressed or implied by purchase of this product
• We’re not liable for misuse of this product.
Email [e-mail]
© 1995-Mar-22 Discount Car Stereo, Inc. All rights reserved. Information in this document is subject
to change without notice. Other products and companies referred to herein are trademarks or
registered trademarks of their respective companies or mark holders.