Mercia Garden Products 01GRO0606-V1 Instruction manual

N/A
Overlap
Cladding
Shiplap
Cladding
Solid Sheet
Roof
T&G Roof
Solid Sheet
Floor
T&G Floor
Fixed
Windows
Opening
Windows
No
Windows
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be erected by two
adults
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are coated with a water based high quality colorant; this only
helps to protect the product during transit and for up to 3 months against
mould. To validate your guarantee and ensure longevity of the product, it is
ESSENTIAL the building is treated with a wood preserver within the rst three
months of assembly and thereafter in accordance with the manufactures
recommendations. Care must be taken to ensure the product is placed on a
suitable base
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products
independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer
to diagrams for the base dimensions, The base should be slightly smaller than
the external measurement of the building, i.e. The cladding should overlap the
base, creating a run o for water. It is also recommended that the oor be at
least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Please retain product label and instructions for future reference
P 1
General Instructions
Refer to the instructions pages for your specic product code
The images used throughout the instruction manual are generic and for
illustration purposes only; they may vary dependant on your actual product. It is
strongly advised they are read and understood before attempting installation.
01GRO0606-V1
6x6 Groundsman Shed Double Doors Opening Window
01GRO0705-V1
7x5 Groundsman Shed Single Door Opening Window
01GRO0806DD-V1
8x6 Groundsman Shed Double Doors Opening Window
01GRO1006DD-V1
10x6 Groundsman Shed Double Doors Opening Windows
01GRO1008DD-V1
10x8 Groundsman Shed Double Doors Opening Windows
01GRO1208DD-V1
12x8 Groundsman Shed Double Doors Opening Windows

P 2
01GRO0705-V1
Overall Dimensions:
Length = 2208mm
Width = 1650mm
Height = 2043mm
Base Dimensions:
Length = 2082mm
Width = 1479mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Door Gable Plain Gable Plain Side Window Side
Floor Roof
Qty 2
Door Window
Content
2
1
34
56
7
8
Fixing Kit
11
12 13 14 15
16 17
10
Fascia - 12x95x930mm Qty 4
Window Strip - 12x45x1100mm
Cover Trim - 12x30x1652mm Qty 4
Finial
Qty 2
Felt
Rim lock
and Handle
Casement Stay
T-hinge Qty 3
Butt hinge
Qty 2
9
Nail Bag
50mm Screw x 12
40mm Screw x 12
Felt Tacks x 70
20mm Screw x 6
30mm Screw x 66
16mm Screw x 6

P 3
Please retain product label and instructions for future reference
21x30mm screws
Step 1
Fix the T-hinges onto the
door and door gable as
shown. using 30mm
screws. Ensure that each
hinge is fixed to the doors
going through to the
framing.
16
Pre drill
hole
30mm
screw
7
Remove transportation blocks
from the bottom of each panel
before beginning assembly.
Each panel should have two
blocks.
Step 2
5
Place the floor on a firm and
level base, ensure base has
suitable drainage free from
areas where standing water
can collect. (See front page for
base requirements).
Step 3
Fix the corner with 3x
50mm screws as shown in
diagram.
Step 4
50mm
screw
Pre drill
hole
The window panel can be fitted
on either the left or right hand
side of the building.
3x50mm screws
2
3

P 4
Please retain product label and instructions for future reference
Fix the corners with 3x
50mm screws as shown in
diagram.
Step 5
50mm
screw
Pre drill
hole
For buildings with no windows
fix a plain panel here.
9x50mm screws
14
Step 6
Fix the roof panels on either
side of the gables as shown
in the diagram. Ensure the
roof framing fits into the
slots at the top of both
gables.
Fix the panels into position
using 30mm screws frpm
the top of the panel,
straight into the rafter.
Pre-drill holes to prevent
spliting.
Ensure the larger overhang
on both panels are facing
each other at the top point.
22x30mm screws
30mm
screw
Pre drill
hole
6
6
Cut the felt into two sheets
measuring 2284mm. Lay
them onto the building as
shown in the diagram and
fix using felt tacks at
100mm intervals.
Step 7
70 x Felt tacks
Felt
tacks
HANDLE
WITH CARE
12
3
4
13

P 5
Please retain product label and instructions for future reference
Fit the cover trims to the front
and back of the building as
shown in the illustration
using 30mm screws.
Trim the length of the cover
trims to the required size
before fitting if necessary.
Pre drill to avoid splitting.
Step 8 11
11
11
11
30mm
screw
12x30mm Screws
Attach the faiscas to the roof
leaving a slight overhang at
the top. Fit the fascias to the
roof over the felt and secure in
place with 40mm screws as
shown.
Pre drill to avoid splitting.
Step 9
12x40mm Screws
Pre drill
hole
12
12
9
9
9
9
40mm
screw
10
8
30mm
16mm
Opening Window
Fixed Window
30mm
screw
30mm
screw
16mm
screw
30mm
screw
17
Place the opening window strip
11mm above the window gap in the
window panel and fix with 3x30mm
screws.
If you would like the windows to be
opening use the butt hinges to
attach the opening window strip
and the opening window together.
Use 30mm screws to fix the butt
hinge to the Window Strip and
16mm screws to fix it to the
Opening Window.
If you want to fix the opening
windows, instead of fixing butt
hinges to the opening window,
use 4x30mm screws to attach
the opening windows to the
window panel as shown in the
diagram.
3x30mm Screws
6x30mm Screws
6x16mm Screws
4x30mm Screws
Step 10

P 6
Please retain product label and instructions for future reference
Step 11
Rim lock fixing
Fig 1. (internal view)
Place the lock onto internal
horizontal framing ensure
alignment with the pre
drilled holes before fixing.
Align Lock keep with lock
and fix with screws provided.
Do not over tighten the
screws, otherwise the
locking mechanism will not
work.
Fig 2.
Place door handle bar
through the lock as in
diagram, fix door handle
onto bar with the flat headed
grub screw.
fig 3. (External view)
Fir the door handle cover
over the bar and fix with
2x30mm screws provided. Fix
the door handle onto bar
with the flat headed grub
screw as in diagram.
Rim lock
Flat head
Grub Screw
2x30mm screw
2x30mm screws
Screws provided with lock
Do not over tighten the screws
30mm
screw Pre drill
hole
14
Step 12
Fix the casement stay to the
opening window then align
the fixings onto the window
panel frame. Ensure the
casement stay fits into
fixings when closed before
screwing them down using
20mm screws. 15
6x20mm screws
20mm
screw
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back