Mercia Garden Products 07PORCOR0909-V1 User manual

07PORCOR0909-V1
N/A
Overlap
Cladding
Shiplap
Cladding
Solid Sheet
Roof
T&G Roof
Solid Sheet
Floor
T&G Floor
Fixed
Windows
Opening
Windows
No
Windows
9x9 Corner summerhouse portabase
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be erected by two
adults
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to
protect the product during transit and for upto 3 months against mould. To
validate your guarantee and ensure longevity of the product, it is ESSENTIAL the
building is treated with a wood preserver within the rst three months of
assembly and thereafter in accordance with the manufactures recommenda-
tions. Care must be taken to ensure the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Whilst all products manufactured are made to the
highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot
accept responsibility for your safety whilst erecting or
using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
**Protim Fentex E5**
Biocidal Product Regulation (EU 528/2012) Article 58 Information
Protim Fentex E2 preserved wood is a “treated article” which incorporates biocidal products.
Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.
Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.
Wear gloves when handling freshly treated wood.
Avoid breathing dust when cutting treated or untreated wood.
Dispose of o-cuts responsibly – do not burn.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer
to diagrams for the base dimensions, The base should be slightly smaller than
the external measurement of the building, i.e. The cladding should overlap the
base, creating a run o for water. It is also recommended that the oor be at
least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Please retain product label and instructions for future reference
P 1
General Instructions
Refer to the instructions pages for you specic product code

1
2
3
4
5
6
7
8
9
40mm Screw x64
70mm Screw x35
100mm Screw x50
*If the portabase is to be located onto a hard standing surface, only the “L” shaped base feet are needed. Position &
identify the high and low spots, securing the feet in place so that the portabase is rm and level in all directions.
On soft ground we recommend the use of post-mix concrete to further secure the groung spikes.
80mm Screw x15
1
2
3
4
Angled Section
Step 1
Arrange the framing as shown in
the illustration and secure together
using 2x100mm screws at each
connecting point.
8x100mm Screws
Pre drill
hole
100mm
screw
Step 2
Place the remaining angled
framing into the base assembly
as shown in the illustration and
secure in place with 4x100mm
screws per angled framing.
12x100mm Screws
Pre drill
hole
100mm
screw
P 2
07PORCOR0909-V1
Overall Dimensions:
Length = 2808mm
Width = 2803mm
Height = 90mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Contents: Angled Section
Framing - 2757mm
Framing - 1206mm
Framing - 1602mm
Angled Framing - 1635mm
Angled Framing - 2450mm
Angled Framing - 2160mm
Angled Framing - 1872mm
Framing - 244mm QTY 2
Contents: Square Section
Framing - 1602mm QTY 2
10 Framing - 2713mm QTY 5
Base Feet QTY 10 Ground Spike QTY 8
11 12
Nail Bag
5
6
7

8
8
8
Step 3
Insert the two smallest pieces of
framing into the base assembly
and secure in place with 4x100mm
screws per framing.
8x100mm Screws
Pre drill
hole
100mm
screw
9
9
10
10
Step 4
Following the same method
outlined in step 1, arrange the
framing as shown in the
illustration and x together using
8x100mm screws.
8x100mm Screws
Square Section
Pre drill
hole
100mm
screw
10
10
10
Step 5
Place the remaining framing into
the base assembly, spacing the
framing equally apart.
Once in place secure to the base
using 4x100mm screws per
framing.
12x100mm Screws
Pre drill
hole
100mm
screw
Step 6
Position the assembled base sections
side by side, ensuring the two sections
are ush, and secure together using
13x80mm screws
13x80mm Screws
Pre drill
hole
80mm
screw
P 3
Please retain product label and instructions for future reference

Step 7
With the portabase in the desired location,
x the “L” shaped feet to the inside of the
framework.
*Position the feet to match the ground,
ensuring the base is level.
Either of the two faces can be used for
securing the feet as this allows for a
greater range of height dierence.
30x40mm Screws
Pre drill
hole
40mm
screw
11
12
Step 8
To secure the portabase to the
ground, hammer the ground
spikes at each corner until
level with the top of the base.
*Use a piece of scrap wood to
prevent damaging the ground
spike.
Step 9
Once the ground spikes are in
position, secure to the frame
using 4x40mm screws per
spike as shown in the illustration.
32x40mm Screws
Pre drill
hole
40mm
screw
*Before beginning assembly of your building ensure the oor bearers run the opposite
way to the portabase.
Once checked and the portabase is rm and level, secure the oor to the base using 70mm
screws. Ensuring to x through the oor bearers into each cross member of the portabase.
P 4
Please retain product label and instructions for future reference