MetaSystem 900000358 User manual

5040327800 06/14 Man.Inst.Gen.PDC STD -EN-
Dedicated system for LAMBORGHINI cars.
Parking Sensor Installation Technical Sheet
Part number 900000358
The technical information included in the following manual must be considered strictly approximate and the manufacturing company will not be
held liable in relation to said information. The technical sta appointed to installation is required to check, with due diligence and under their own
responsibility, the information provided herein based on the type of vehicle (ex. specic connection points for the model).
Part number 900000359
To achieve precise installation, we recommend the use of the tool kit

INSTALLATION REGULATIONS
• Before performing any operation, disconnect the negative pole on the battery.
• The electronic control units of the kits must be installed exclusively inside the car
cabin.
• To attach them we recommend using velcro or straps, avoid drilling holes in the
sheet metal on the car.
• For position and connections it is good practice to refer to the instructions.
• To avoid vibrations, we recommend wrapping the system cables with fabric tape.
• Strictly avoid quick electrical couplings.
• To set up connections to the vehicle’s system, crimp the wire using splices and insu-
late the joint with insulating tape.
SYSTEM PROGRAMMING
Before installing the system, it will be necessary to congure the parking sensor kit modules correctly. Using
the programmer included in tool kit 90000359 and referring to the relative programming manual, set the
parameters as illustrated in the images below. The number beside the description identies the function re-
quiring programming.
Before disconnecting the module, press the READ key and make sure the settings are correct. The CAN BUS
module must not be programmed.
Rear Parking Sensor Control Unit
Front Parking Sensor Control Unit
2

ELECTRICAL CONNECTIONS
The required electrical connections described in the general installation manual must be set up on the 40-
pole QUADLOCK connector installed behind the stereo.
3
BLACK
RED PURPLE/
BLACK
RED/
BLACK

REAR CABLE GLAND
4
Using the supplied corrugated cable duct and silicone sheath, follow the existing route for the light cables to
reach the cabin.
NOTE: The templates provided at the end of the manual must be printed out making sure they are the correct
size.
CAPSULE INSTALLATION POINTS
Using the dedicated templates, mark the distances on the rear and front bumpers.
CABRIO COUPE’COUPE’

5
TAKING DOWN THE REAR BUMPER
Proceed with taking down the rear bumper by following the instructions provided in procedure LB715
08 07 03.
Also remove the black plastic support.
REAR CAPSULE INSTALLATION
We recommend preventively drilling a centring hole of 2.5mm Ø.
Then, with a suitable 19 mm mill (included in the tool kit for Category 900000359) drill a hole in the bumper
from the outside in.
For this installation use capsule supports without locking rings “O” (see General installation manual).
The sensors must be painted beforehand, in the same colour as the car.
Near the sensors measurement, drill a hole in the rear plastic support using a 35 mm mill.

6
REAR SENSOR CABLING
Wrap the cables with the heat-resistant sheath, cat. 470 827 222, and secure the cabling to the crosspiece on
the car.
REAR BUMPER RE-ASSEMBLY
Proceed with re-assembling the rear bumper by following the instructions provided in procedure LB715
08 07 03.

7
FRONT CABLE GLAND
Using the supplied corrugated cable duct, follow the existing cable route to reach the cabin.
TAKING DOWN THE FRONT BUMPER
Proceed with taking down the front bumper by following the instructions provided in procedure LB715
08 07 03.
Also take down the polyurethane vibration-damper support.
Near the sensors measurement, drill a hole in the vibration-damper support using a 35 mm mill.

8
FRONT CAPSULE INSTALLATION
We recommend preventively drilling a centring hole of 2.5mm Ø.
Then, with a suitable 19 mm mill (included in the tool kit for Category 900000359) drill a hole in the bumper
from the outside in.
For this installation use capsule supports without locking rings “O” (see General Installation manual).
The sensors must be painted beforehand, in the same colour as the car.
FRONT SENSOR CABLING
Attach the cables to the crosspiece on the car.
NOTE: prior to installation it is necessary to remove the sensor’s support tabs as illustrated below.

9
FRONT BUMPER RE-ASSEMBLY
Proceed with re-assembling the front bumper by following the instructions provided in procedure LB715
08 07 03.

10
POSITIONING THE PARTS
The rear management control unit must be set up in the module compartment behind the backrest on the
passenger’s side.
The front management control unit and the CAN BUS utility module must be set up over the GFA control unit
located under the glove compartment, on the passenger’s side.

The front on/o button must be set up inside the plastic cover on the ceiling of the car, near the rear-view
mirror.
BUTTON INSTALLATION
Cut the template out being careful to use a ruler with millimetre scale to make sure it has printed out with
zoom at 100%.
Attach the paper template with masking tape and, as described, use a 5 mm
bit to drill the four corners and a 3 mm bit to drill the sides.
Use cutters to remove the part inside the rectangle and then use a le to smo-
oth down the edges of the newly cut rectangle.
Place button support B in hole D being careful that the four retaining hooks lock it onto the hole.
Place button A in the support, securing it by the two clip fasteners C.
Connect the 2-pin connector of the wire to the button.
11
CABRIO COUPE’

FRONT MASKING
OFF
OFF
12
Mask the front system with the engine running.

REAR MASKING
13
Mask the rear system with the engine running.

14
01020304050
01020304050
FRONT PARKING SYSTEM: LH FRONT SIDE SENSOR

01020304050
01020304050
15
FRONT PARKING SYSTEM: RH FRONT SIDE SENSOR

16
01020304050
01020304050
FRONT PARKING SYSTEM: LH FRONT CENTRAL SENSOR
350 mm from the centre of the side capsule

17
FRONT PARKING SYSTEM: RH FRONT CENTRAL SENSOR
01020304050
01020304050
350 mm from the centre of the side capsule

01020304050
01020304050
18
FRONT PARKING SYSTEM:
LH REAR SIDE SENSOR

19
01020304050
01020304050
REAR PARKING SYSTEM:
RH REAR SIDE SENSOR

20
01020304050
01020304050
REAR PARKING SYSTEM: LH REAR CENTRAL SENSOR
470 mm from the centre of the side capsule